DatasheetsPDF.com

ATA6562 Datasheet PDF

Microchip
Part Number ATA6562
Manufacturer Microchip
Title High-Speed CAN Transceiver
Description The ATA6562/3 is a high-speed CAN transceiver that provides an interface between a Controller Area Network (CAN) protocol controller and the physi...
Features
• Fully ISO 11898-2, ISO 11898-2: 2016 and SAE J2962-2 Compliant
• CAN FD Ready
• Communication Speed up to 5 Mbps
• ISO 26262 Functional Safety Ready
• Low Electromagnetic Emission (EME) and High Electromagnetic Immunity (EMI)
• Differential Receiver with Wide Common-Mode Range
• ATA6562: Silent Mo...

File Size 1.44MB
Datasheet PDF File ATA6562 PDF File


ATA6562 ATA6562 ATA6562




Similar Ai Datasheet

ATA6020N : The ATA6020N is a member of Atmel’s 4-bit single-chip microcontroller family. It contains ROM, RAM, parallel I/O ports, one 8-bit programmable multifunction timer/counter with modulator function, voltage supervisor, interval timer with watchdog function and a sophisticated on-chip clock generation with external clock input and integrated RC-oscillators. Figure 1-1. Block Diagram VSS VDD OSC1 www.DataSheet4U.com Brown-out protect RESET Voltage monitor External input VMI RC oscillators External clock input UTCM Timer 1 interval- and watchdog timer Clock management ROM 2 K x 8 bit RAM 256 x 4 bit Timer 2 8/12-bit timer with modulator T2I T2O SD Data direction BP20/NTE Port 2 BP21 BP22.

ATA6025 : The ATA6025 is a monolithic circuit based on Atmel’s smart power BCD60-III technology. It is a universal IC for monitoring basic functions of an automotive application. It is possible to monitor the battery voltage (VKL15) and an external 5V voltage regulator. With the independent watchdog the correct function of a microcontroller can be observed. If a failure occurs, the output NOTL switches to high after a time delay. During standby mode the current consumption is reduced to a minimum. ATA6025 Rev. 4716C–AUTO–09/05 Figure 1-1. Block Diagram RREF VB VCC VKL15 VBG Oscillator on chip trimming BIAS current OSC - VCCH + VCC over- and undervoltage detection - + VCCL .

ATA6026 : The ATA6026 is used to drive a continuous-current motor in a full H-bridge configuration. An external microcontroller controls the driving function of the ATA6026 by www.DataSheet4U.com providing a PWM signal and a direction signal, and allows the usage of the ATA6026 in a windshield wiper application, for example. The ATA6026 supports PWM and direction-controlled driving of four external power MOSFETs with two external bootstrap capacitors. The PWM control is performed by the high-side switch. The opposite low-side switch is permanently ON in the driving phase. Motor braking is performed using the low-side switches. A programmable dead time is included to prevent peak currents within the H-.

ATA6140 : The integrated circuit ATA6140 is used in relay-controlled automotive fla.

ATA6264 : With the introduction of the ATA6264, Atmel® introduces a new generation of airbag power supplies for future airbag systems tailored to the needs of the automotive industry. It is designed in Atmel’s 0.8 micron BCDMOS technology. ATA6264 contains all the necessary blocks to supply the microcontroller, the firing capacitors, and peripheral components of the airbag system. The power supply specifically fulfills the power requirements of dual-voltage microcontrollers used in modern ECUs. The integrated watchdog and diagnosis blocks additionally support the safety aspects. The 8-MHz 16-bit SPI enables a high communication speed. Despite the high-level functionality, ATA6264 comes in a space-savi.

ATA6285 : ATA6285 and ATA6286 are highly integrated smart RF micro transmitter ICs for 315 MHz and 433 MHz, suited for ASK and FSK with typically 20 Kbits/s data rate in Manchester mode. The devices combine the functionality of the RF transmitter ICs ATA5756/ATA5757 with the programmable low-power AVR 8-bit Flash microcontroller in a single QFN32 package (5 mm × 5 mm). The ATA6285 and ATA6286 include a dedicated ADC interface for simple capacitive sensors as well as an on-chip temperature sensor. Three sensor interfaces are available for a capacitive range of 2 pF to 16 pF, where one channel can be configured as motion wake-up in the range of 3 pF to 5 pF. The ICs are suited for use in tire pressure m.

ATA6286 : ATA6285 and ATA6286 are highly integrated smart RF micro transmitter ICs for 315 MHz and 433 MHz, suited for ASK and FSK with typically 20 Kbits/s data rate in Manchester mode. The devices combine the functionality of the RF transmitter ICs ATA5756/ATA5757 with the programmable low-power AVR 8-bit Flash microcontroller in a single QFN32 package (5 mm × 5 mm). The ATA6285 and ATA6286 include a dedicated ADC interface for simple capacitive sensors as well as an on-chip temperature sensor. Three sensor interfaces are available for a capacitive range of 2 pF to 16 pF, where one channel can be configured as motion wake-up in the range of 3 pF to 5 pF. The ICs are suited for use in tire pressure m.

ATA6405 : The ATA6405 is a fully integrated system voltage supply IC. The device is designed for the 12/24 V board voltage system in a motor vehicle. In order to minimize power consumption, a switching regulator generates a voltage for supplying the internal linear regulator with a 5 V output voltage for microcontrollers. To monitor the microcontroller, provision has been made for a window watchdog feature incorporating a reset logic function. The voltage system IC has three modes: active, Standby and OFF. One control input serves to facilitate the selection between the active and Standby modes. Another input permits the selection between the Standby and OFF modes. In the OFF mode, a maximum quiescent.

ATA644S28 : YANGZHOU POSITIONING TECH. CO., LTD PSTATA644S28 Asymmetric thyristors Features: . All Diffused Structure . Center Amplifying Gate Configuration . Blocking capabilty up to 2100 volts . Guaranteed Maximum Turn-Off Time . High dV/dt Capability . Pressure Assembled Device ELECTRICAL CHARACTERISTICS AND RATINGS Blocking - Off State VRRM (1) VDRM (1) VRSM (1) 20 2800 2100 VRRM = Repetitive peak reverse voltage VDRM = Repetitive peak off state voltage VRSM = Non repetitive peak reverse voltage (2) Repetitive peak reverse leakage and off state lCeraitkicaaglerate of voltage rise IRRM IDRM dV/dt (4) 1000 mA 200 mA (3) 500 V/sec Conducting - on state Notes: All ratings are specified for .

ATA6560 : ATA6560/1 High-Speed CAN Transceiver with Standby Mode CAN FD Ready Features • Fully ISO 11898-2, ISO 11898-5, and SAE J2284 Compliant • CAN FD Ready • Communication Speed up to 5 Mbps • Low Electromagnetic Emission (EME) and High Electromagnetic Immunity (EMI) • Differential Receiver with Wide Common-Mode Range • ATA6560: Silent Mode (Receive Only) • Remote Wake-Up Capability via CAN Bus • Functional Behavior Predictable under All Supply Conditions • Transceiver Disengages from the Bus when Not Powered Up • RXD Recessive Clamping Detection • High Electrostatic Discharge (ESD) Handling Capability on the Bus Pins • Bus Pins Protected Against Transients in Automotive Environments • Transmit .

ATA6561 : ATA6560/1 High-Speed CAN Transceiver with Standby Mode CAN FD Ready Features • Fully ISO 11898-2, ISO 11898-5, and SAE J2284 Compliant • CAN FD Ready • Communication Speed up to 5 Mbps • Low Electromagnetic Emission (EME) and High Electromagnetic Immunity (EMI) • Differential Receiver with Wide Common-Mode Range • ATA6560: Silent Mode (Receive Only) • Remote Wake-Up Capability via CAN Bus • Functional Behavior Predictable under All Supply Conditions • Transceiver Disengages from the Bus when Not Powered Up • RXD Recessive Clamping Detection • High Electrostatic Discharge (ESD) Handling Capability on the Bus Pins • Bus Pins Protected Against Transients in Automotive Environments • Transmit .

ATA6563 : The ATA6562/3 is a high-speed CAN transceiver that provides an interface between a Controller Area Network (CAN) protocol controller and the physical Two-Wire CAN bus. The transceiver is designed for high-speed (up to 5 Mbps) CAN applications in the automotive industry, providing differential transmit and receive capability to (a microcontroller with) a CAN protocol controller. It offers improved electromagnetic compatibility (EMC) and ESD performance as well as features such as: • Ideal passive behavior to the CAN bus when the supply voltage is off • Direct interfacing to microcontrollers with supply voltages from 3V to 5V (ATA6563) Three operating modes together with the dedicated fail-saf.

ATA6564 : The ATA6564 is a high-speed CAN transceiver that provides an interface between a Controller Area Network (CAN) protocol controller and the physical Two-Wire CAN bus. The transceiver is designed for high-speed (up to 5 Mbit/s) CAN applications in the automotive industry, providing differential transmit and receive capability to (a microcontroller with) a CAN protocol controller. It offers improved electromagnetic compatibility (EMC) and ESD performance as well as features such as: • Ideal passive behavior to the CAN bus when the supply voltage is off • Direct interfacing to microcontrollers with supply voltages from 3V to 5V Two operating modes together with the dedicated fail-safe features m.

ATA6570 : The ATA6570 is a stand-alone, high-speed CAN transceiver with partial networking that interfaces a Controller Area Network (CAN) protocol controller and the physical two-wire CAN bus designed for high-speed CAN applications in the automotive environment. The ATA6570 provides local and enhanced remote wake-up capabilities and is available in 14-lead SOIC and VDFN packages. It has a very low-power consumption in Standby and Sleep mode. Besides local wake-up via the WAKE pin and remote wake-up pattern according to ISO 11898-2:2016, ATA6570 additionally supports ISO 11898-2:2016 compliant CAN partial networking. A CAN frame decoder evaluates the bus traffic and checks for a matching frame that .

ATA6602 : ATA6602/ATA6603 is a single-package dual-chip circuit family for LIN-bus slave node applications. It supports highly integrated solutions for in-vehicle LIN networks. The LIN-system-basis-chip (LIN-SBC) consists of a LIN transceiver, voltage regulator and window watchdog. The second chip is a microcontroller out of Atmel®'s series of AVR 8-bit microcontrollers with advanced RISC architecture. Microcontroller with LIN Transceiver, 5V Regulator and Watchdog ATA6602/ ATA6603 Figure 1-1. Application Diagram LIN Bus www.DataSheet4U.com ATA6602/ATA6603 MCU LIN-SBC 4921C–AUTO–01/07 2. Pin Configuration Figure 2-1. Pinning QFN48, 7 mm × 7 mm PC1 PC0 ADC7 GND AREF ADC6 AVCC PB5 PB4 PB3 PB2 P.

ATA6603 : ATA6602/ATA6603 is a single-package dual-chip circuit family for LIN-bus slave node applications. It supports highly integrated solutions for in-vehicle LIN networks. The LIN-system-basis-chip (LIN-SBC) consists of a LIN transceiver, voltage regulator and window watchdog. The second chip is a microcontroller out of Atmel®'s series of AVR 8-bit microcontrollers with advanced RISC architecture. Microcontroller with LIN Transceiver, 5V Regulator and Watchdog ATA6602/ ATA6603 Figure 1-1. Application Diagram LIN Bus www.DataSheet4U.com ATA6602/ATA6603 MCU LIN-SBC 4921C–AUTO–01/07 2. Pin Configuration Figure 2-1. Pinning QFN48, 7 mm × 7 mm PC1 PC0 ADC7 GND AREF ADC6 AVCC PB5 PB4 PB3 PB2 P.




Since 2006. D4U Semicon,
Electronic Components Datasheet Search Site. (Privacy Policy & Contact)