DatasheetsPDF.com

MP9841 Datasheet PDF


Part Number MP9841
Manufacturer MPS
Title Synchronous Step-Down Converter
Description The MP9841 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. It offers a very compact sol...
Features include over-current protection (OCP), short-circuit protection (SCP), and thermal shutdown. An open-drain power good (PG) signal indicates when the output is within 10% of its nominal voltage. The MP9841 is available in a space-saving QFN-16 (3mmx4mm) package. FEATURES
• 2μA Low Shutdown Supply Cu...

File Size 1.47MB
Datasheet MP9841 PDF File








Similar Ai Datasheet

MP900 : The Photon Counting Head MP 900 series is designed for applications in all fields of single photon detection, e.g. chemoluminescence, bioluminescence, in-vitro assay, environmental measurements or pure research. It is an easy to use module, containing the Channel Photomultiplier, a high voltage power supply, a discrimination amplifier and a pulse shaper for fast output pulses. An installed active quenching systems avoids over-illumination to the detector. It is also possible to apply an external gate function for time correlated photon counting. Strong variations in light levels are possible due to the high dynamic range of the installed CPM. The exceptional low noise and high sensitivity fa.

MP901 : of Sensor Characters Rs/R0 Rs/Rs0 Acetone Alcohol H2 Methanal Toluene Iso-butane Smoke Concentration (ppm) Fig3.Typical Sensitivity Curve Rs means resistance in target gas with different concentration, R0 means resistance of sensor in clean air. All tests are finished under standard test conditions. MP901 measure 10ppmAlcohol Fig4.Typical temperature/humidity characteristics Rs means resistance of sensor in 10ppm alcohol under different tem. and humidity. Rso means resistance of the sensor in 50ppm alcohol under 20℃/55%RH. Voltage Output(V) Acetone Alcohol H2 Methanal Toluene Iso-butane Concentration (ppm) Fig5.Responce and Resume Fig6.Linearity curve Tel: 86-371-67169097/67169670 F.

MP9141 : The MP9141 is a monolithic step-down switch mode converter with a built in internal power MOSFET. It achieves 2A continuous output current over a wide input supply range with excellent load and line regulation. TheMP9141requires a minimum number of readily available standard external components. Current mode operation provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-bycycle current limiting and thermal shutdown. In shutdown mode the regulator draws 25µA of supply current. FEATURES • 2A Output Current • 0.22Ω Internal Power MOSFET Switch • Stable with Low ESR Output Ceramic Capacitors • Up to 95% Efficiency • 25µA Shutdown Mode • Fixed .

MP915 : MP900 and MP9000 Series Kool-Pak® Power Film Resistors TO-126, TO-220 and TO-247 Style Page 1 of 2 Low Cost Heat Sink Mountable Design featuring an Exposed Ceramic Heat Dissipating Mounting Surface Use your thermal design experience with power semiconductors in TO-126, TO-220, and TO-247 style power packages to help you get the most out of this unique family of power resistors. The thermal design issues are the same where power handling capability is based on the case temperature which is maintained in your design. MP915 TO-126 Style Power Package • 15 Watts at +25°C Case Temperature, derated to zero at +150°C. • Exposed Ceramic Heat Dissipating Mounting Surface. • Resistance Range of 0.020.

MP9159A : The MP9159A is a monolithic step-down, switch-mode converter with built-in power MOSFETs. It achieves a 1 A continuous output current from a 2.5 V to 6 V input voltage range with excellent load and line regulation. The output voltage can be regulated as low as 0.6 V. The constant-on-time (COT) control scheme provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. The MP9159A is available in a small TSOT23-8 package and requires a minimum number of readily available, standard, external components. The MP9159A is ideal for a wide range of applications including high-performance DSPs, FPGAs, PDAs, a.

MP916 : MP900 and MP9000 Series Kool-Pak® Power Film Resistors TO-126, TO-220 and TO-247 Style Page 1 of 2 Low Cost Heat Sink Mountable Design featuring an Exposed Ceramic Heat Dissipating Mounting Surface Use your thermal design experience with power semiconductors in TO-126, TO-220, and TO-247 style power packages to help you get the most out of this unique family of power resistors. The thermal design issues are the same where power handling capability is based on the case temperature which is maintained in your design. MP915 TO-126 Style Power Package • 15 Watts at +25°C Case Temperature, derated to zero at +150°C. • Exposed Ceramic Heat Dissipating Mounting Surface. • Resistance Range of 0.020.

MP9161A : The MP9161A is a monolithic, step-down, switch-mode converter with built-in internal power MOSFETs. It achieves a 2A continuous output current from a 2.5V to 6V input voltage range with excellent load and line regulation. The output voltage is regulated as low as 0.6V. The constant-on-time (COT) control scheme provides fast transient response and eases loop stabilization. Fault condition protection includes cycle-by-cycle current limiting and thermal shutdown. The MP9161A is available in a small TSOT23-8 package and requires a minimum number of readily available, standard, external components. The MP9161A is ideal for a wide range of applications including high performance DSPs, FPGAs, PDAs,.

MP9218 : The MP9218 is a high performance, regulated charge pump converter. Its input voltage ranges from 2.8V to Vout. The output voltage is regulated to a fixed 5V. No external inductor is required for simplicity and compactness. Internal soft-start circuit effectively reduces the in-rush current both while start-up and mode change. The MP9218 is available in a compact TQFN-6 (2mmx2mm) package FEATURES  Input Voltage Range: 2.8V to 5V  Internal Soft-Start  Output Maximum Current up to 110mA  Fixed 5V Output Voltage with 30mV Ripple  2X Charge Pump  Fixed 1.35MHz Switching Frequency  Over Current Protection  Short Circuit Protection  In-rush Current limit  TQFN-6 (2mmx2mm) package and Lea.

MP92265 : FEATURES The MP92265 is a high-frequency, synchronous, rectified, step-down, switch-mode converter with built-in power MOSFETs. The MP92265 offers a very compact solution that achieves 5A of output current with excellent load and line regulation over a wide input supply range. The MP92265 uses synchronous mode operation to achieve high efficiency over the output current load range. Current-mode operation provides fast transient response and eases loop stabilization. Full protection features include over-current protection (OCP) and thermal shutdown. The MP92265 requires a minimal number of readily available, standard, external components and is available in a space-saving, 8-pin, TSOT23 pa.

MP925 : MP900 and MP9000 Series Kool-Pak® Power Film Resistors TO-126, TO-220 and TO-247 Style Page 1 of 2 Low Cost Heat Sink Mountable Design featuring an Exposed Ceramic Heat Dissipating Mounting Surface Use your thermal design experience with power semiconductors in TO-126, TO-220, and TO-247 style power packages to help you get the most out of this unique family of power resistors. The thermal design issues are the same where power handling capability is based on the case temperature which is maintained in your design. MP915 TO-126 Style Power Package • 15 Watts at +25°C Case Temperature, derated to zero at +150°C. • Exposed Ceramic Heat Dissipating Mounting Surface. • Resistance Range of 0.020.

MP930 : MP900 and MP9000 Series Kool-Pak® Power Film Resistors TO-126, TO-220 and TO-247 Style Page 1 of 2 Low Cost Heat Sink Mountable Design featuring an Exposed Ceramic Heat Dissipating Mounting Surface Use your thermal design experience with power semiconductors in TO-126, TO-220, and TO-247 style power packages to help you get the most out of this unique family of power resistors. The thermal design issues are the same where power handling capability is based on the case temperature which is maintained in your design. MP915 TO-126 Style Power Package • 15 Watts at +25°C Case Temperature, derated to zero at +150°C. • Exposed Ceramic Heat Dissipating Mounting Surface. • Resistance Range of 0.020.

MP9361 : The MP9361 is a high performance, regulated charge pump converter. Its input voltage ranges from 2.8V to Vout. The output voltage is regulated to a fixed 5V. No external inductor is required for simplicity and compactness. Internal soft-start circuit effectively reduces the in-rush current both while start-up and mode change. The MP9361 is available in a compact TSOT23-6 package MP9361 High Performance Regulated Charge Pump FEATURES  Input Voltage Range: 2.8V to 5V  Internal Soft-Start  Output Maximum Current up to 110mA  Fixed 5V Output Voltage with 30mV Ripple  2X Charge Pump  Fixed 1.35MHz Switching Frequency  Over Current Protection  Short Circuit Protection  In-rush Current li.

MP9459 : The MP9459 is a fully integrated, highfrequency, synchronous, rectified, step-down, switch-mode converter with internal power MOSFETs. The device is a compact solution that achieves 4A of output current over a wide input range with excellent load and line regulation. It uses synchronous mode operation for higher efficiency over the output current load range. Constant-on-time (COT) control operation provides very fast transient response, easy loop design, and very tight output regulation. Full protection features include short-circuit protection (SCP), over-current protection (OCP), under-voltage protection (UVP), and thermal shutdown. The MP9459 requires a minimal number of readily available.

MP9486 : The MP9486 is a high-voltage, step-down, switching regulator that delivers up to 1A of continuous current to the load. It integrates a high-side, high-voltage, power MOSFET with a current limit of 2.5A, typically. The wide 4.5V to 100V input range accommodates a variety of step-down applications, making it ideal for automotive, industry, and lighting applications. Hysteretic voltage-mode control is employed for very fast response. MPS’s proprietary feedback control scheme minimizes the number of required external components. The switching frequency can be up to 1MHz, allowing for small component size. Thermal shutdown and short-circuit protection (SCP) provide reliable and fault-tolerant ope.

MP962-2 : The Photon Counting module series MP96X-2 / MP97X-2 is specially designed for particle measurement with 530 nm and 632 nm lasers. Based on the standard multialkali photocathode, the sensitive diameter is reduced to 2mm in order to achieve an excellent low dark count performance. With an optional SMA adapter, also a fiber read out is possible. The MP96X-2/MP97X-2 series satisfies by exceptional low after pulses. It is an easy to use module, containing the Channel Photomultiplier, a high voltage power supply, a discrimination amplifier and a pulse shaper for fast output pulses. An installed active quenching system avoids over- illumination to the detector. Features · Specially selected for be.

MP963-2 : The Photon Counting module series MP96X-2 / MP97X-2 is specially designed for particle measurement with 530 nm and 632 nm lasers. Based on the standard multialkali photocathode, the sensitive diameter is reduced to 2mm in order to achieve an excellent low dark count performance. With an optional SMA adapter, also a fiber read out is possible. The MP96X-2/MP97X-2 series satisfies by exceptional low after pulses. It is an easy to use module, containing the Channel Photomultiplier, a high voltage power supply, a discrimination amplifier and a pulse shaper for fast output pulses. An installed active quenching system avoids over- illumination to the detector. Features · Specially selected for be.

MP972-2 : The Photon Counting module series MP96X-2 / MP97X-2 is specially designed for particle measurement with 530 nm and 632 nm lasers. Based on the standard multialkali photocathode, the sensitive diameter is reduced to 2mm in order to achieve an excellent low dark count performance. With an optional SMA adapter, also a fiber read out is possible. The MP96X-2/MP97X-2 series satisfies by exceptional low after pulses. It is an easy to use module, containing the Channel Photomultiplier, a high voltage power supply, a discrimination amplifier and a pulse shaper for fast output pulses. An installed active quenching system avoids over- illumination to the detector. Features · Specially selected for be.




Since 2006. D4U Semicon,
Electronic Components Datasheet Search Site. (Privacy Policy & Contact)