DatasheetsPDF.com

LTC1047


Part Number LTC1047
Manufacturer Linear Technology
Title Dual Micropower Chopper Stabilized Operational Amplifier
Description of these types of problems (and some advice on avoiding them), see the LTC1051/LTC1053 data sheet. Input Capacitance The LTC1047 has approximately...
Features
■ No External Components Required
■ Maximum Offset Voltage: 10µV
■ Maximum Offset Voltage Drift: 50nV/°C
■ Supply Current: 80µA
■ Minimum CMRR: 110dB
■ Minimum PSRR: 105dB
■ Single Supply Operation: 4.75V to 16V
■ Common Mode Range Includes GND
■ Output Swings to GND
■ Typical Overload Recovery Time...

File Size 149.76KB
Datasheet LTC1047 PDF File








Similar Ai Datasheet

LTC1040 : of internal operation is essential to proper application. The most obvious difference between the LTC1040 and other comparators is the dual differential input structure. Functionally, when the sum of inputs is positive, the comparator output is high and when the sum of the inputs is negative, the output is low. This unique input structure is achieved with CMOS switches and a precision capacitor array. Because of the switching nature of the inputs, the concept of input current and input impedance needs to be examined. The equivalent input circuit is shown in Figure 1. Here, the input is being driven by a resistive source, RS, with a bypass capacitor, CS. The bypass capacitor may or may not be.

LTC1041 : U U FEATURES s Micropower 1.5µW (1 Sample/Second) s Wide Supply Range 2.8V to 16V s High Accuracy Guaranteed SET POINT Error ±0.5mV Max Guaranteed Deadband ±0.1% of Value Max s Wide Input Voltage Range V+ to Ground s TTL Outputs with 5V Supply s Two Independent Ground-Referred Control Inputs s Small Size 8-Pin SO U APPLICATIO S s Temperature Control (Thermostats) s Motor Speed Control s Battery Charger s Any ON-OFF Control Loop , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOS is a trademark of Linear Technology Corporation. LTC1041 BANG-BANG Controller DESCRIPTIO The LTC®1041 is a monolithic CMOS BANG-BANG controller manufactured using Linear Technology’s enh.

LTC1042 : LTC1042 Window Comparator U U FEATURES ■ Micropower 1.5µW (1 Sample/Second) ■ Wide Supply Range — 2.8V to 16V ■ High Accuracy Center Error ±1mV Max Width Error ±0.15% Max ■ Wide Input Voltage Range V+ to Ground ■ TTL Outputs with 5V Supply ■ Two Independent Ground-Referred Control Inputs ■ Small Size 8-Pin MiniDIP U APPLICATIO S ■ Fault Detectors ■ Go/No-Go Testing ■ Microprocessor Power Supply Monitor , LTC and LT are registered trademarks of Linear Technology Corporation. LTCMOS is a trademark of Linear Technology Corp. DESCRIPTIO The LTC®1042 is a monolithic CMOS window comparator manufactured using Linear Technology’s enhanced LTCMOS™ silicon gate process. Two high impedance voltage i.

LTC1043 : .

LTC1044 : .

LTC1044 : The LTC®1044 is a monolithic CMOS switched capacitor voltage converter which is manufactured using Analog Devices’ enhanced LTCMOS™ silicon gate process. The LTC1044 provides several voltage conversion functions: the input voltage can be inverted (VOUT = –VIN), doubled (VOUT = 2VIN), divided (VOUT = VIN/2) or multiplied (VOUT = ± nVIN). Designed to be pin-for-pin and functionally compatible with the popular 7660, the LTC1044 provides significant features and improvements over earlier 7660 designs. These improvements include: full 1.5V to 9V supply operation over the entire operating temperature range, without the need for external protection diodes; two and one-half times lower quiescent cur.

LTC1044A : The LTC®1044A is a monolithic CMOS switched-capacitor voltage converter. It plugs in for ICL7660/LTC1044 in applications where higher input voltage (up to 12V) is needed. The LTC1044A provides several conversion functions without using inductors. The input voltage can be inverted (VOUT = –VIN), doubled (VOUT = 2VIN), divided (VOUT = VIN/2) or multiplied (VOUT = ±nVIN). To optimize performance in specific applications, a boost function is available to raise the internal oscillator frequency by a factor of seven. Smaller external capacitors can be used in higher frequency operation to save board space. The internal oscillator can also be disabled to save power. The supply current drops to 1.5µ.

LTC1045 : The LTC®1045 is a hex level translator manufactured using Linear Technology’s enhanced LTCMOSTM silicon gate process. It consists of six high speed comparators with output latches and three-state capability. Each comparator’s plus input is brought out separately. The minus inputs of comparators 1 to 4 are tied to VTRIP1 while 5 and 6 are tied to VTRIP2. The ISET pin has several functions. When taken to V + the outputs are latched and power is completely shut off. Power/speed can be programmed by connecting ISET to V – through an external resistor. Efficiently Translate Voltage Levels Internal Hysteresis for Noise Immunity Output Latches Included Three-State Outputs Programmable Power/Speed .

LTC1046 : LTC1046 “Inductorless” 5V to – 5V Converter + U U FEATURES s 50mA Output Current s Plug-In Compatible with ICL7660/LTC1044 s ROUT = 35Ω Maximum s 300µA Maximum No Load Supply Current at 5V s Boost Pin (Pin 1) for Higher Switching Frequency s 97% Minimum Open-Circuit Voltage Conversion Efficiency s 95% Minimum Power Conversion Efficiency s Wide Operating Supply Voltage Range: 1.5V to 6V s Easy to Use s Low Cost U APPLICATIO S s Conversion of 5V to ± 5V Supplies s Precise Voltage Division, VOUT = VIN/2 s Supply Splitter, VOUT = ± VS/2 DESCRIPTIO The LTC®1046 is a 50mA monolithic CMOS switched capacitor voltage converter. It plugs in for the ICL7660/ LTC1044 in 5V applications where more out.

LTC1049 : The LTC®1049 is a high performance, low power zero-drift operational amplifier. The two sample-and-hold capacitors usually required externally by other chopper stabilized amplifiers are integrated on the chip. Further, the LTC1049 offers superior DC and AC performance with a nominal supply current of only 200µA. The LTC1049 has a typical offset voltage of 2µV, drift of 0.02µV/°C, 0.1Hz to 10Hz input noise voltage of 3µVP-P and typical voltage gain of 160dB. The slew rate is 0.8V/µs with a gain bandwidth product of 0.8MHz. Overload recovery time from a saturation condition is 6ms, a significant improvement over chopper amplifiers using external capacitors. The LTC1049 is available in a standa.




Since 2006. D4U Semicon,
Electronic Components Datasheet Search Site. (Privacy Policy & Contact)