DatasheetsPDF.com

NCP436


Part Number NCP436
Manufacturer ON Semiconductor
Title 3A Ultra-Small Controlled Load Switch
Description Pin Name Pin Number Type IN A2, B2 POWER GND EN OUT C1 C2 A1, B1 POWER INPUT OUTPUT Description Load−switch input voltage; connect a 1 mF...
Features
• 1.0 V − 3.6 V Operating Range
• 20 mW P MOSFET at 3.6 V
• DC Current Up to 3 A
• Output Auto−discharge
• Active High EN Pin
• WLCSP6 1 x 1.5 mm
• These are Pb−Free Devices Typical Applications
• Mobile Phones
• Tablets
• Digital Cameras
• GPS
• Portable Devices http://onsemi.com MARKING DIAGRAM ...

File Size 92.51KB
Datasheet NCP436 PDF File








Similar Ai Datasheet

NCP4300A : NCP4300A Dual Operational Amplifier and Voltage Reference The NCP4300A is a monolithic integrated circuit specifically designed to control the output current and voltage levels of switch mode battery chargers and power supplies. This device contains a precision 2.6 V shunt reference and two operational amplifiers. Op−Amp 1 is designed to perform voltage control and has its non−inverting input internally connected to the reference. Op−Amp 2 is designed for current control and has both inputs uncommitted. The NCP4300A offers the power converter designer a control solution that features increased precision with a corresponding reduction in system complexity and cost. This device is available i.

NCP4302 : Pin Number Symbol 1 SYNC/CS 2 TRIG 3 CATH 4 VREF 5 DLYADJ 6 GND 7 DRV 8 VCC Description Connected to the flyback winding. The current on this pin is sensed and used to turn on the Synchronous Rectification MOSFET (SRFET). This pin is also used to sense the zero crossing of the MOSFET current either using the RDS(on) of the SRFET or using an external current sense resistor connected between drain of the SRFET and the flyback winding. Input pin for direct turn−off of the MOSFET. Typically connected to a signal from primary controller (for CCM mode) or a signal derived from the transformer (for QR mode). Has very short propagation delay to output (50 ns). Feedback compensation pin for the.

NCP4303A : Pin No. Pin Name Function 1 VCC Supplies the driver 2 Min_toff Minimum off time adjust 3 Min_ton Minimum on time adjust 4 TRIG/Disable Forced reset input 5 CS Current sense of the SR MOSFET 6 COMP Compensation inductance connection 7 GND IC ground 8 DRV Gate driver output Pin Description VCC supply terminal of the controller. Accepts up to 30 V continuously. Adjust the minimum off time period by connecting resistor to ground. Adjust the minimum on time period by connecting resistor to ground. This ultrafast turn-off input offers the possibility to further improve efficiency and performance in applications that work in deep Continuous Conduction Mode (CCM). Activates sle.

NCP4303B : Pin No. Pin Name Function 1 VCC Supplies the driver 2 Min_toff Minimum off time adjust 3 Min_ton Minimum on time adjust 4 TRIG/Disable Forced reset input 5 CS Current sense of the SR MOSFET 6 COMP Compensation inductance connection 7 GND IC ground 8 DRV Gate driver output Pin Description VCC supply terminal of the controller. Accepts up to 30 V continuously. Adjust the minimum off time period by connecting resistor to ground. Adjust the minimum on time period by connecting resistor to ground. This ultrafast turn-off input offers the possibility to further improve efficiency and performance in applications that work in deep Continuous Conduction Mode (CCM). Activates sle.

NCP4304A : Pin No. Pin Name Function 1 VCC Supplies the driver 2 MIN_TOFF Minimum off time adjust 3 MIN_TON Minimum on time adjust 4 TRIG/DIS Forced reset input 5 CS Current sense of the SR MOSFET 6 COMP Compensation inductance connection 7 GND IC ground 8 DRV Gate driver output Pin Description Supply terminal of the controller. Accepts up to 30 V continuously. Adjust the minimum off time period by connecting resistor to ground. Adjust the minimum on time period by connecting resistor to ground. This ultrafast input turns off the SR MOSFET in CCM applications. Activates sleep mode if pulled up for more than 100 ms. This pin detects if the current flows through the SR MOSFET and/or.

NCP4304B : Pin No. Pin Name Function 1 VCC Supplies the driver 2 MIN_TOFF Minimum off time adjust 3 MIN_TON Minimum on time adjust 4 TRIG/DIS Forced reset input 5 CS Current sense of the SR MOSFET 6 COMP Compensation inductance connection 7 GND IC ground 8 DRV Gate driver output Pin Description Supply terminal of the controller. Accepts up to 30 V continuously. Adjust the minimum off time period by connecting resistor to ground. Adjust the minimum on time period by connecting resistor to ground. This ultrafast input turns off the SR MOSFET in CCM applications. Activates sleep mode if pulled up for more than 100 ms. This pin detects if the current flows through the SR MOSFET and/or.

NCP4305 : NCP4305 Secondary Side Synchronous Rectification Driver for High Efficiency SMPS Topologies The NCP4305 is high performance driver tailored to control a synchronous rectification MOSFET in switch mode power supplies. Thanks to its high performance drivers and versatility, it can be used in various topologies such as DCM or CCM flyback, quasi resonant flyback, forward and half bridge resonant LLC. The combination of externally adjustable minimum off-time and on-time blanking periods helps to fight the ringing induced by the PCB layout and other parasitic elements. A reliable and noise less operation of the SR system is insured due to the Self Synchronization feature. The NCP4305 also util.

NCP4306 : of the naming convention used for image sensors. For reference documentation, including information on evaluation kits, please visit our web site at www.onsemi.com. +VBULK M1 LLC STAGE CONTROL M2 Tr1 N2 N1 N3 C1 OK1 R1 C3 VCC DRV MIN_TOFF GND MIN_TON CS LLD TRIG NCP4306 RMIN_TOFF RMIN_TON RLLD M3 +VOUT C2 RTN M4 VCC DRV MIN_TOFF GND MIN_TON CS LLD TRIG NCP4306 D1 R2 C4 RMIN_TOFF RMIN_TON RLLD Figure 1. Typical Application Example – LLC Converter with optional LLD and Trigger Utilization www.onsemi.com 2 NCP4306 VBULK TR1 C1 R1 C2 D3 VCC M2 D4 FLYBACK C3 CONTROL CIRCUITRY DRV M1 FB CS R2 OK1 RMIN_TOFF RMIN_TON RLLD R3 C4 VCC DRV MIN_TOFF GND.

NCP4308 : NCP4308 Synchronous Rectifier Controller The NCP4308 is a synchronous rectifier controller for switch mode power supplies. The controller enables high efficiency designs for flyback, quasi resonant flyback and LLC topologies. Externally adjustable minimum off−time and on−time blanking periods provides flexibility to drive various MOSFET package types and PCB layout. A reliable and noise less operation of the SR system is insured due to the Self Synchronization feature. The NCP4308 also utilizes Kelvin connection of the driver to the MOSFET to achieve high efficiency operation at full load. The precise turn−off threshold, extremely low turn−off delay time and high sink current capability of.

NCP43080 : ver. A, B, C, D ver. Q Pin Name 1 1 VCC 2 2 MIN_TOFF 3 3 MIN_TON 4 4 LLD 5 − NC 6 6 CS 7 7 GND 8 8 DRV − 5 MAX_TON Description Supply voltage pin Adjust the minimum off time period by connecting resistor to ground. Adjust the minimum on time period by connecting resistor to ground. This input modulates the driver clamp level and/or turns the driver off during light load conditions. Leave this pin opened or tie it to ground. Current sense pin detects if the current flows through the SR MOSFET and/or its body diode. Basic turn−off detection threshold is 0 mV. A resistor in series with this pin can decrease the turn off threshold if needed. Ground connection for the SR MOSFET driver, .

NCP4318 : Pin Number NCP4318A NCP4318B Name Description 1 1 GATE1 Gate drive output for SR MOSFET1 2 2 GND Ground 3 4 VS1 Synchronous rectifier source sense input for SR1 4 3 VD1 Synchronous rectifier drain sense input. IOFFSET1 current source flows out of the VD1 pin such that an external series resistor can be used to adjust the synchronous rectifier turn−off threshold. The IOFFSET1 current source is turned off when VDD is under−voltage or when switching is disabled in green mode 5 5 VS2 Synchronous rectifier source sense input for SR2 6 6 VD2 Synchronous rectifier drain sense input. IOFFSET2 current source flows out of the VD2 pin such that an external series resistor.

NCP431A : Programmable Precision References NCP431A, SC431A, NCP431B, SC431B, NCP432B, SC432B Series The NCP431/NCP432 integrated circuits are three−terminal programmable shunt regulator diodes. These monolithic IC voltage references operate as a low temperature coefficient zener which is programmable from Vref to 36 V using two external resistors. These devices exhibit a wide operating current range of 40 mA to 100 mA with a typical dynamic impedance of 0.22 W. The characteristics of these references make them excellent replacements for zener diodes in many applications such as digital voltmeters, power supplies, and op amp circuitry. The 2.5 V reference makes it convenient to obtain a stable refere.

NCP431B : Programmable Precision References NCP431A, SC431A, NCP431B, SC431B, NCP432B, SC432B Series The NCP431/NCP432 integrated circuits are three−terminal programmable shunt regulator diodes. These monolithic IC voltage references operate as a low temperature coefficient zener which is programmable from Vref to 36 V using two external resistors. These devices exhibit a wide operating current range of 40 mA to 100 mA with a typical dynamic impedance of 0.22 W. The characteristics of these references make them excellent replacements for zener diodes in many applications such as digital voltmeters, power supplies, and op amp circuitry. The 2.5 V reference makes it convenient to obtain a stable refere.

NCP432 : Pin Name Pin Number Type IN A2 POWER GND EN OUT B1 POWER B2 INPUT A1 OUTPUT Description Load−switch input voltage; connect a 1 mF or greater ceramic capacitor from IN to GND as close as possible to the IC. Ground connection. Enable input, logic high turns on power switch. Load−switch output; connect a 1 mF ceramic capacitor from OUT to GND as close as possible to the IC is recommended. BLOCK DIAGRAM Figure 2. Block Diagram http://onsemi.com 2 NCP432, NCP433 MAXIMUM RATINGS Rating Symbol Value Unit IN, OUT, EN, Pins: From IN to OUT Pins: Input/Output Maximum Junction Temperature Storage Temperature Range Human Body Model (HBM) ESD Rating are (Notes 1 and 2) VEN, VIN, VOUT VVO.

NCP4326 : Pin No. Symbol Type Description 1 CP1 Error Amplifier This pin is the output of the error amplifier 1 (monitoring the secondary voltage #1) and is Output 1 available for loop compensation purpose. 2 FB1 Voltage This is the inverting input of the error amplifier 1. It is connected to the secondary voltage Feedback 1 #1 via a bridge resistor divider. 3 EN2 Soft−Start and This pin enables or disables the driver 2. An internal current source with an external Enable or Disable capacitor generates also a soft−start feature for limiting the startup peak current on the the Driver 2 controlled output. This pin can be left open and by default it enables the driver 2, but without soft−s.

NCP4328 : NCP4328A TSOP−5 NCP4328B TSOP−6 11 22 56 44 −5 33 Pin Name VCC GND VSNS ISNS LED FBC Description Supply voltage pin Ground Output voltage sensing pin, connected to output voltage divider Current sensing input for output current regulation, connect it to shunt resistor in ground branch. PWM LED driver output. Connected to LED cathode with current define by external serial resistance Output of current sinking OTA amplifiers driving feedback optocoupler’s LED. Connect here compensation networks as well. ABSOLUTE MAXIMUM RATINGS Rating Symbol Value Unit Input Voltage VCC −0.3 to 40.0 V FBC, LED Voltage VFBC, VLED −0.3 to VCC + 0.3 V VSNS, ISNS Voltage VSNS,VISNS −0.3 to.

NCP432B : Programmable Precision References NCP431A, SC431A, NCP431B, SC431B, NCP432B, SC432B Series The NCP431/NCP432 integrated circuits are three−terminal programmable shunt regulator diodes. These monolithic IC voltage references operate as a low temperature coefficient zener which is programmable from Vref to 36 V using two external resistors. These devices exhibit a wide operating current range of 40 mA to 100 mA with a typical dynamic impedance of 0.22 W. The characteristics of these references make them excellent replacements for zener diodes in many applications such as digital voltmeters, power supplies, and op amp circuitry. The 2.5 V reference makes it convenient to obtain a stable refere.




Since 2006. D4U Semicon,
Electronic Components Datasheet Search Site. (Privacy Policy & Contact)