PLAYER. CDX-GT360 Datasheet

CDX-GT360 Datasheet PDF

Part CDX-GT360
Description FM/MW/LW/SW COMPACT DISC PLAYER
Feature CDX-GT360; CDX-GT317EE/GT360 SERVICE MANUAL Ver. 1.1 2007.03 Saudi Arabia Model CDX-GT360 East European Model.
Manufacture Sony
Datasheet
Download CDX-GT360 Datasheet




CDX-GT360
CDX-GT317EE/GT360
SERVICE MANUAL
Ver. 1.1 2007.03
Saudi Arabia Model
CDX-GT360
East European Model
CDX-GT317EE
(Photo: CDX-GT317EE)
• The tuner and CD sections have no adjustments.
Model Name Using Similar Mechanism
CD Drive Mechanism Type
Optical Pick-up Name
CDX-GT262/GT217
MG-101TA-188//Q
DAX-25A
SPECIFICATIONS
CD player section
Signal-to-noise ratio
Frequency response
Wow and flutter
120 dB
10 – 20,000 Hz
Below measurable limit
Tuner section
FM
Tuning range
GT317EE:
FM1/FM2: 87.5 – 108.0 MHz
(at 50 kHz step)
FM3: 65 – 74 MHz (at 30 kHz step)
GT360:
87.5 – 108.0 MHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity
9 dBf
Selectivity
75 dB at 400 kHz
Signal-to-noise ratio 67 dB (stereo), 69 dB (mono)
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono)
Separation
35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
MW/LW (GT317EE)
Tuning range
MW: 531 – 1,602 kHz
LW: 153 – 279 kHz
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
MW: 30 µV, LW: 40 µV
MW/SW (GT360)
Tuning range
MW: 531 – 1,602 kHz
SW1: 2,940 – 7,735 kHz
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575 kHz)
Antenna terminal
External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity
30 µV
Power amplifier section
Outputs
Speaker outputs (sure seal connectors)
Speaker impedance 4 – 8 ohms
Maximum power output
GT317EE: 50 W × 4 (at 4 ohms)
GT360: 52 W × 4 (at 4 ohms)
– Continued on next page –
FM/MW/LW COMPACT DISC PLAYER
CDX-GT317EE
FM/MW/SW COMPACT DISC PLAYER
CDX-GT360
9-887-460-02
2007C04-1
© 2007.03
Sony Corporation
eVehicle Division
Published by Sony Techno Create Corporation
http://www.Datasheet4U.com



CDX-GT360
CDX-GT317EE/GT360
General
Outputs
Inputs
Tone controls
Power requirements
Dimensions
Mounting dimensions
Mass
Supplied accessories
Audio outputs terminal (sub/rear switchable)
Power antenna relay control terminal
Power amplifier control terminal
Telephone ATT control terminal (GT317EE)
BUS control input terminal
BUS audio input terminal
Antenna input terminal
AUX input jack (stereo mini jack)
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
12 V DC car battery (negative ground)
Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Approx. 1.2 kg (2 lb. 11 oz.)
Card remote commander: RM-X151
Parts for installation and connections (1 set)
Design and specifications are subject to change without
notice.
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential dif ference g enerated b y the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damag ed and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK
The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, w hen c hecking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Notes on Chip Component Replacement
• Never reuse a disconnected chip component.
•N otice that the minus side of a tantalum capacitor may be damaged
by heat.
TEST DISCS
Please use the following test discs for the check on the CD section.
YDES-18 (Part No. 3-702-101-01)
PATD-012 (Part No. 4-225-203-01)
CAUTION
Use of controls or adjustments or performance of procedures
other than those specif ied herein ma y result in hazardous
radiation exposure.
If the optical pic k-up block is defecti ve, please replace the whole
optical pick-up block.
Never turn the semi-fixed resistor located at the side of optical pick-
up block.
optical pick-up
semi-fixed resistor
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
WITH MARK 0 ON THE SCHEMA TIC DIAGRAMS AND IN
THE P ARTS LIST ARE CRITICAL T O SAFE OPERA TION.
REPLACE THESE COMPONENTS WITH SONY
P ARTS
WHOSE P ART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2



CDX-GT360
CDX-GT317EE/GT360
This compact disc player is classif ied as a CLASS 1 LASER
product. The CLASS 1 LASER PRODUCT label is located on the
exterior.
• CD playback
You can play CD-DA (also containing CD TEXT*), CD-R/CD-
RW (MP3/WMA files also containing Multi Session .
Type of discs
Label on the disc
CD-DA
This label is located on the bottom of the chassis.
MP3
WMA
* A CD TEXT disc is a CD-DA that includes information such as
disc, artist and track name.
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (stick y, less prone to flo w)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
MAIN BOARD
CN350
J-2502-076-1
SERVO BOARD
CN2
3







@ 2014 :: Datasheetspdf.com ::
Semiconductors datasheet search & download site (Privacy Policy & Contact)