DatasheetsPDF.com

DS1413 Datasheet

Part Number DS1413
Manufacturers Dallas Semiconductor
Logo Dallas Semiconductor
Description Passive Serial Port iButton Holder
Datasheet DS1413 DatasheetDS1413 Datasheet (PDF)

  DS1413   DS1413
DS1413 Passive Serial Port iButton ™ Holder www.dalsemi.com FEATURES § Small size, low-cost interface to an RS232C COM Port for reading and writing iButton devices § Supports reading all and writing nonEPROM iButton devices at regular speed § Powered entirely from an RS232 interface www.DataSheet4U.com § Standard DB female connector for mating to the COM Port of a computer with a DS9098 iButton Retainer for a single iButton or MicroLAN Cable (DS1402x) ORDERING INFORMATION DS1413 DB–9 Connector DESCRIPTION The DS1413 Passive Serial Port iButton Holder is a simple, lowcost adapter which performs RS232C (±12V) level conversion, allowing a non-EPROM iButton to be read and written directly. It can also read all EPROM based iButtons. The serial port must support a data transmission rate of 115.2 kbits/s in order to create the 1-Wire time slots correctly. Nearly all PCs and several other hardware platforms support the required bit rate and are fully compatible with the DS1413. Since an eig.






Part Number DS14196
Manufacturers ETCTI
Logo ETCTI
Description DS14196 EIA/TIA-232 5 Driver x 3 Receiver (Rev. D)
Datasheet DS1413 DatasheetDS14196 Datasheet (PDF)

  DS1413   DS1413
.






Part Number DS14196
Manufacturers National Semiconductor
Logo National Semiconductor
Description EIA/TIA-232 5 Driver x 3 Receiver
Datasheet DS1413 DatasheetDS14196 Datasheet (PDF)

  DS1413   DS1413
DS14196 EIA/TIA-232 5 Driver x 3 Receiver February 2000 DS14196 EIA/TIA-232 5 Driver x 3 Receiver General Description The DS14196 is a five driver, three receiver device which conforms to the EIA/TIA-232-E and the ITU-T V.28 standards. The flow-through pinout facilitates simple non-crossover board layout. The DS14196 provides a peripheral side one-chip solution for the common 9-pin serial RS-232 interface between data terminals and data communications equipment. The DS14196 offers optimum performance when used with the DS14185 3 x 5 Driver/Receiver, a host side one-chip solution for the common 9-pin serial RS-232 interface between data terminals and data communications equipment. Features.






Part Number DS14185
Manufacturers ETCTI
Logo ETCTI
Description DS14185 EIA/TIA-2323 Driver x 5 Receiver (Rev. C)
Datasheet DS1413 DatasheetDS14185 Datasheet (PDF)

  DS1413   DS1413
.






Part Number DS14185
Manufacturers National Semiconductor
Logo National Semiconductor
Description EIA/TIA-232 3 Driver x 5 Receiver
Datasheet DS1413 DatasheetDS14185 Datasheet (PDF)

  DS1413   DS1413
DS14185 EIA/TIA-232 3 Driver x 5 Receiver April 1999 DS14185 EIA/TIA-232 3 Driver x 5 Receiver Features n n n n n n n Replaces one 1488 and two 1489s Conforms to EIA/TIA-232-E 3 drivers and 5 receivers Flow through pinout Failsafe receiver outputs 20-pin SOIC package LapLink ® compatible −200 kbps data rate General Description The DS14185 is a three driver, five receiver device which conforms to the EIA/TIA-232-E standard. The flow-through pinout facilitates simple non-crossover board layout. The DS14185 provides a one-chip solution for the common 9-pin serial RS-232 interface between data terminal and data communications equipment. Connection Diagram www.DataSheet4U.com SOIC Functiona.






Passive Serial Port iButton Holder

DS1413 Passive Serial Port iButton ™ Holder www.dalsemi.com FEATURES § Small size, low-cost interface to an RS232C COM Port for reading and writing iButton devices § Supports reading all and writing nonEPROM iButton devices at regular speed § Powered entirely from an RS232 interface www.DataSheet4U.com § Standard DB female connector for mating to the COM Port of a computer with a DS9098 iButton Retainer for a single iButton or MicroLAN Cable (DS1402x) ORDERING INFORMATION DS1413 DB–9 Connector DESCRIPTION The DS1413 Passive Serial Port iButton Holder is a simple, lowcost adapter which performs RS232C (±12V) level conversion, allowing a non-EPROM iButton to be read and written directly. It can also read all EPROM based iButtons. The serial port must support a data transmission rate of 115.2 kbits/s in order to create the 1-Wire time slots correctly. Nearly all PCs and several other hardware platforms support the required bit rate and are fully compatible with the DS1413. Since an eight bit character (6 data bits plus start-and stop bit) on the RS232C port operating at 115.2 kbits/s is used to form a single 1-Wire time slot, the maximum effective 1-Wire transfer rate is 14.4 kbits/s (regular speed). The DS1413 has a DS9098 retainer for a single F5 Micro-Can and can replace the DS9097 COM Port Adapter in applications that use only a single iButton. Multiple iButtons can be connected to the DS1413 using standard MicroLAN Cables and button holders (see DS1401 and DS1402x data s.



2008-09-02 : DS1410D    DS1410E    DS1411    DS1413    DS14185    DS14196    DS1425    DS14285    DS14287    DS1481   


@ 2014 :: Datasheetspdf.com ::
Semiconductors datasheet search & download site (Privacy Policy & Contact)