Document
6N135/6, HCNW135/6 HCPL-2502/0500/0501 Single Channel, High Speed Optocouplers
Data Sheet
Lead (Pb) Free RoHS 6 fully compliant RoHS 6 fully compliant options available; -xxxE denotes a lead-free product
Description These diode-transistor optocouplers use an insulating layer between a LED and an integrated photodetector to provide electrical insulation between input and output. Separate connections for the photodiode bias and output-transistor collector increase the speed up to a hundred times that of a conventional phototransistor coupler by reducing the base-collector capacitance. These single channel optocouplers are available in 8-Pin DIP, SO-8 and Widebody package configurations. The 6N135, HCPL-0500, and HCNW135 are for use in TTL/ CMOS, TTL/LSTTL or wide bandwidth analog applications. Current transfer ratio (CTR) for these devices is 7% minimum at IF = 16 mA. The 6N136, HCPL-2502, HCPL-0501, and HCNW136 are designed for high speed TTL/TTL applications. A standard 16 mA TTL sink current through the input LED will provide enough output current for 1 TTL load and a 5.6 kΩ pull-up resistor. CTR for these devices is 19% minimum at IF = 16 mA. Functional Diagram
NC 1 ANODE 2 CATHODE 3
NC 4
8 VCC 7 VB 6 VO 5 GND
TRUTH TABLE (POSITIVE LOGIC)
LED VO ON LOW OFF HIGH
Features
• High speed: 1 Mb/s
• TTL compatible
• Available in 8-Pin DIP, SO-8, widebody packages
• Open collector output
• Safety approval
UL for
Recognized – 3750 1 minute for HCNW
Varnmds fOorp1tiomnin0u2t0ed(5e0v0ic0eVs)rms
per UL1577
CSA Approved
IEC/EN/DIN EN 60747-5-5 Approved
–––deVVVvIIIOOOiRRRcMMMes===
567 V peak for SO-8 devices 630 V peak for DIP 300 mil devices 1414 V peak for DIP 400 mil (widebody)
• Dual channel version available (253X/053X/0534)
Applications
• High voltage insulation • Video signal isolation • Line receivers • Feedback element in switched mode power supplies • High speed logic ground isolation
– TTL/TTL, TTL/CMOS, TTL/LSTTL • Replaces pulse transformers • Replaces slow phototransistor isolators • Analog signal ground isolation
A 0.1 µF bypass capacitor must be connected between pins 5 and 8.
CAUTION: It is advised that normal static precautions be taken in handling and assembly of this component to prevent damage and/or degradation which may be induced by ESD.
Schematic
2 ANODE +
VF CATHODE -
3
IF
SHIELD
ICC 8 VCC
IB 7
VB
IO 6 VO
5 GND
Selection Guide
M inimum CMR 8-Pin DIP Small-Outline
(300 Mil)
SO-8
Widebody (400 Mil)
Current Single Dual
dV/dt (V/µs)
(VVCM) RTraatniosf(e%r)
Channel Package
Channel Package*
Single Channel Package
Dual Channel Package*
Single Channel Package
1,000
10
7
6N135 HCPL-2530 HCPL-0500 HCPL-0530 HCNW135
19
6N136 HCPL-2531 HCPL-0501 HCPL-0531 HCNW136
15 HCPL-2502
*Technical data for these products are on separate Avago publications.
2
Ordering Information
6N135, 6N136, HCPL-2502, HCPL-0500, HCPL-0501 are UL Recognized with 3750 Vrms for 1 minute per UL1577.
HCNW135, HCNW136 are UL CSA Component Acceptance
RNeoctoicgen#iz5e,dFiwleitChA58080302V4r.ms
for
1
minute
per
UL1577.
All
these
devices
are
approved
under
Part number 6N135 6N136 HCPL-2502
HCPL-0500 HCPL-0501 HCNW135 HCNW136
Option RoHS Non RoHS Compliant Compliant
Package
Surface Gull Mount Wing
Tape & Reel
UL 5000 Vrms/ra1tMinignute
IEC/EN/DIN EN 60747-5-5 Quantity
-000E No option
50 per tube
-300E
#300
XX
50 per tube
-500E
#500
X XX
1000 per reel
-020E
#020
-320E
#320
300mil DIP-8
X
X
-520E
#520
X XX
X X X
50 per tube 50 per tube 1000 per reel
-060E
#060
X 50 per tube
-360E
#360
XX
X 50 per tube
-560E
#560
X XX
X 1000 per reel
-000E No option
100 per tube
-500E -060E
#500 #060
SO-8
X
XX
1500 per reel X 100 per tube
-560E
#560
X XX
X 1500 per reel
-000E No option 400 mil
-300E
#300 Widebody X
X
-500E #500 DIP-8 X X X
X X X
X 42 per tube X 42 per tube X 750 per reel
To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry.
Example 1: HCPL-2502-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with
IEC/EN/DIN EN 60747-5-5 Safety Approval in RoHS compliant. Example 2: HCPL-2502 to order product of 300 mil DIP package in tube packaging and non RoHS compliant. Option datasheets are available. Contact your Avago sales representative or authorized distributor for information.
Remarks: The notation‘#XXX’is used for existing products, while (new) products launched since 15th July 2001 and RoHS compliant option will use ‘-XXXE‘.
3
Package Outline Drawings 8-Pin DIP Package (6N135/6, HCPL-2502)
9.65 ± 0.25 (0.380 ± 0.010)
TYPE NUMBER
87
65
OPTION CODE*
A XXXXZ
DATE CODE
YYWW RU EEE
UL RECOGNITION
1 2 3 4 LOT ID
1.19 (0.047) MAX.
1.78 (0.070) MAX.
3.56 ± 0.13 (0.140 ± 0.005.