DatasheetsPDF.com

TD9054 Dataheets PDF



Part Number TD9054
Manufacturers Techcode
Logo Techcode
Description 0.8A Standalone Linear Li-lon Battery Charger
Datasheet TD9054 DatasheetTD9054 Datasheet (PDF)

T  echcode®     0.8A Standalone Linear Li-lon Battery Charger with Thermal Regulation   DATASHEET TD9054 General Description  Features    The TD9054 is a complete constant‐current/constant‐voltage  linear charger for single cell lithium‐ion batteries. Its SOT23‐5  package  and  low  external  component  count  make  the  TD9054 ideally suited for portable applications. Furthermore,  the  TD9054  can  work  within  USB  and  wall  adapter.  No  blocking  diode  is  required  due  to  the  int.

  TD9054   TD9054



Document
T  echcode®     0.8A Standalone Linear Li-lon Battery Charger with Thermal Regulation   DATASHEET TD9054 General Description  Features    The TD9054 is a complete constant‐current/constant‐voltage  linear charger for single cell lithium‐ion batteries. Its SOT23‐5  package  and  low  external  component  count  make  the  TD9054 ideally suited for portable applications. Furthermore,  the  TD9054  can  work  within  USB  and  wall  adapter.  No  blocking  diode  is  required  due  to  the  internal  PMOSFET  architecture  and  have  prevent  to  negative  Charge  Current  Circuit.  Thermal  feedback  regulates  the  charge  current  to  limit  the  die  temperature  during  high  power  operation  or  high  ambient  temperature.  The  charge  voltage  is  fixed  at  4.2V,  and  the  charge  current  can  be  programmed  externally  with  a  single  resistor.  The  TD9054  automatically  terminates  the  charge  cycle  when  the  charge  current  drops  to  1/10th  the  programmed  value  after  the  final  float  voltage  is  reached.  TD9054 Other features include current monitor, under voltage  lockout,  automatic  recharge  and  charge  status  pin  to  indicate  charge termination.  Programmable Charge Current Up to 800mA   No MOSFET, Sense Resistor or Blocking Diode Rquired   Complete  Linear  Charger  in  SOT23‐5  Package  for  Single  Cell Lithium‐Ion Batteries   Constant‐Current/Constant‐Voltage   Charges Single Cell Li‐Ion Batteries Directly from USB Port  Preset 4.2V Charge Voltage with 1.5% Accuracy   Automatic Recharge     Charge Status Output Pins   C/10 Charge Termination   2.9V Trickle Charge Threshold       Soft‐Start Limits Inrush Current   Available  Radiator  in  SOT23‐5  Package,  the  Radiator  need connect GND or impending  Applications   Cellular Telephones, PDAs, GPS   Charging Docks and Cradles   Digital Still Cameras, Portable Devices   USB Bus‐Powered Chargers, Chargers  Package Types      Figure 1. Package Types of TD9054  March,  20,  2013.                                                        Techcode  Semiconductor  Limited                                                  www.techcodesemi.com  1  T  echcode®     0.8A Standalone Linear Li-lon Battery Charger with Thermal Regulation   Pin Configurations    Pin Description  CHRG 1 GND 2 BAT 3 5 PROG 4 VCC  Figure 2 Pin Configuration of TD9054(Top View) DATASHEET TD9054 Pin Name  CHRG  GND  BAT  Vcc  PROG  Pin Number    When the battery is being charged, the CHRG  pin  is  pulled  low  by  an  internal  switch,  1  otherwise CHRG pin is in high impedance state.  2  GND  Connect  the  positive  terminal  of  the  battery  to  BAT  pin.  BAT  pin  draws  less  than  2uA  3  current in chip disable mode or in sleep mode. BAT pin provides charge current to the  battery and provides regulation voltage of 4.2V.  VIN  is  the  power  supply  to  the  internal  circuit.  When  VIN  drops  to  within  30mv  of  the  4  BAT  pin  voltage,  TD9054  enters  low  power  sleep  mode,  dropping  BAT  pin’s  current  to  less than 2uA  charge  current  is  set  by  connecting  a  resistor  RPROG  from  this  pin  to  GND.  When  in  precharge  mode,  the  PROG  pin’s  voltage  is  regulated  to  0.1V.  When  in  constant  charge  5  current mode, the PROG pin’s voltage is regulated to 1V. In all modes during charging,  the voltage on PROG pin can be used to measure the charge current as follows:  IBAT=(VPROG/RPROG)*1000‐‐‐‐(TD9054)  Ordering Information  TD9054 □ □    Circuit Type                                                                                                                    Packing: Blank:Tube R: Tape and Reel T : SOT23-5   March,  20,  2013.                                                        Techcode  Semiconductor  Limited                                                  www.techcodesemi.com  2  T  echcode®     0.8A Standalone Linear Li-lon Battery Charger with Thermal Regulation   Function Block Diagram  DATASHEET TD9054 145°C Tdie TA 80%Vin TTEMP TTEMP 45%Vin VCC schmitt CA SHDN CHRG 1 Vcc 4 1000x 5uA MA 3 BAT R1 R2 REF 1.22V R3 1V R4 0.1V R5 TO BAT 3uA 2.9V 5 PROG     VCC 2 GND   March,  20,  2013.                                                        Techcode  Semiconductor  Limited                                                  www.techcodesemi.com  3  T  echcode®     0.8A Standalone Linear Li-lon Battery Charger with Thermal Regulation   Electrical Characteristics  DATASHEET TD9054 (VIN = 5V, TA = 25°C unless otherwise specified)  Parameters  Symbol  Input Supply Voltage  VCC  Input Supply Current  Icc  Regulated Output (Float) Voltage  VFLOAL  Test Condition    Charge Mode, RPROG =2k    Shutdown Mode (RPROG Not  Connected, VCC < VBAT, or VCC< VUV)  0℃≤TA≤85℃,IBAT=40mA  BAT Pin Current    IBAT  RPROG = 2k, Current Mode    RPROG = 3k, Current Mode  Standby Mode, VBAT = 4.2V  Trickle Charge Current  ITRIKL  VBAT


TD7502 TD9054 TD9157


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)