Our Performance Your Reputation
100MHz Ultra Low Noise/Low G-Sensitivity OCXO
NI-100M-6900 series
NI-100M-6900 Series in 36.3x27.2mm DIP package
NI-100M-6900 series is a 100.000 MHz high performance (VC)OCXO offering Ultra Low Phase Noise(ULPN), low G sensitivity(LGS) and tight frequency stability down to ±50ppb(-20ºC to +70ºC). The part comes in a small hermetically sealed through hole package which makes it suitable for humid environmental conditions.
FEATURES
Ultra Low Phase Noise & Low G-Sensitivity Hermetically Sealed Package Tight Frequency Stability Low Power Consumption Fast Warm-up Time Electrical Frequency Tuning Input Reference Voltage Output RoHS-Compliant (lead-free)
APPLICATIONS
Instrument Reference
RoHS Compliant Standard
Microwave Communication
Clock Reference for Microwave Signal Source
Test & Measurement
Telecom Systems
Radar Systems
Medical (MRT)
ELECTRICAL SPECIFICATIONS
Test conditions: VDC = +5 V; VCO = +5 V; at +25 ± 3°C unless otherwise identified
1. OUTPUT (PIN = “R.F. OUTPUT”)
Parameter 1.1. Frequency (Fo)
1.2. Initial Accuracy
1.3. Waveform 1.4. Level 1.5. Load 1.6. Harmonics 1.7. Spurious
Min. Typ. Max. 100.000000
-0.3 +0.3
Sine wave +15
50 -30 -100
Unit MHz
ppm
Test Condition
@ +25 ±1°C after turn on power 30 minutes Vco=+5V
dBm Ω dBc dBc
+/-10%
http://www.taitien.com E-Mail:
[email protected] Specifications subject to change without notice
Rev(1)12/2015 Page 1of 4
2. FREQUENCY STABILITY
Parameter
Min.
Typ.
Max.
2.1. Ambient
±50, ±100 ±200, ±500
-20oC ~ +70oC -40oC ~ +85oC
Aging
2.2.
Daily
-5
+5
Yearly -200
+200
15 Years
-2
+2
2.3. Voltage
-5
+5
2.4. Load
-5 +5
2.5. Short term
0.05
2.6. Warm-up
-50
+50
2.7. G-Sensitivity (each axis)
1
2.8. Phase Noise (Max.)
Option A
-100 -130 -157 -180 -185 -185
Option B
-105 -135 -162 -180 -185 -185
Our Performance Your Reputation
Unit Test Condition
ppb
°C
ppb ppb ppm ppb ppb ppb ppb
ppb/g
dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz
referenced to 25°C Refer to Table 1 : Ordering Information after 30 days of continuous operation
±5% change ±10% change root Allan variance for τ=1 sec in 5 minutes @ +25 ±1°C
referenced to 1 hour
Refer to Table 1 : Ordering Information @ 10Hz @ 100Hz @ 1KHz @ 10KHz @ 100KHz @ 1MHz
3. ELECTRICAL FREQUENCY ADJUSTMENT (PIN = “VCO INPUT”)
Parameter
3.1. Tuning Range 3.2. Control Voltage 3.3. Slope 3.4. Center Voltage 3.5. Linearity
Min. ±2.5
0
-10
Typ. Max.
Positive +5
+10.0 +10
Unit ppm
V
Test Condition Referenced to frequency at nominal Center Voltage
V %
4. INPUT POWER (PIN = “+VDC”)
Parameter
Min.
4.1. Voltage Current
+4.75
4.2. Steady State
During Warm-Up
Typ. +5
Max. +5.25
2.1 950
Unit V
W @ +25°C
mA
Test Condition
http://www.taitien.com E-Mail:
[email protected] Specifications subject to change without notice
Rev(1)12/2015 Page 2of 4
5. ENVIRONMENTAL
Our Performance Your Reputation
Parameter
Reference Std.
Test Condition
5.1. Operable Temperature 5.2. Storage Temperature 5.3. Humidity
5.4. Vibration (non-operating)
-40°C to +85°C
-55°C to +105°C MIL-STD-202, Method 103
Test Condition A
MIL-STD-202, Method 201
Note 1
95% RH @ +40°C,non-condensing,240 hours 0.06” Total p-p, 10 to 55 Hz
5.5. Shock (non-operating)
MIL-STD-202, Method 213, Test Condition J
30g, 11ms, half-sine
Note 1 : Output maintained over this temperature range. Other requirements of this specification may not be met when operating outside the temperature range in 2.1.
Table 1 : ORDERING INFORMATION
Ambient
Option
Phase Noise Option
Temp. (°C ) -20°C ~+70oC
±100 ppb ±50 ppb
-40oC~+85oC
±500 ppb ±200 ppb
Other specifications may be available upon request.
A NI-100M-6900 NI-100M-6910 NI-100M-6920 NI-100M-6930
B NI-100M-6901 NI-100M-6911 NI-100M-6921 NI-100M-6931
Phase Noise Test Data
http://www.taitien.com E-Mail:
[email protected] Specifications subject to change without notice
Rev(1)12/2015 Page 3of 4
OUTLINE DRAWING
Our Performance Your Reputation
http://www.taitien.com E-Mail:
[email protected] Specifications subject to change without notice
Rev(1)12/2015 Page 4of 4
.