Document
Document 894-1
Chip Inductors –0603HL Series (1608)
• Higher inductance values than other 0603 inductors • Inductance range: 330 nH – 3.3 µH
Part number1
Inductance2 ±5% (nH)
0603HL-331XJR_ 330 @ 25 MHz 0603HL-391XJR_ 390 @ 25 MHz 0603HL-471XJR_ 470 @ 25 MHz 0603HL-511XJR_ 510 @ 25 MHz 0603HL-561XJR_ 560 @ 25 MHz
0603HL-681XJR_ 680 @ 25 MHz
0603HL-821XJR_ 820 @ 25 MHz
0603HL-102XJR_
1000 @ 25 MHz
0603HL-122XJR_
1200 @ 25 MHz
0603HL-152XJR_
1500 @ 25 MHz
0603HL-182XJR_ 0603HL-222XJR_ 0603HL-272XJR_ 0603HL-332XJR_
1800 @ 25 MHz 2200 @ 25 MHz 2700 @ 25 MHz 3300 @ 25 MHz
Q typ3
13 @ 25 MHz 13 @ 25 MHz 12 @ 25 MHz 12 @ 25 MHz 12 @ 25 MHz
12 @ 25 MHz 14 @ 25 MHz 14 @ 25 MHz 14 @ 25 MHz 15 @ 25 MHz
16 @ 25 MHz 16 @ 25 MHz 16 @ 25 MHz 18 @ 25 MHz
SRF typ4 DCR max5
Irms6 Color
(MHz) (Ohms) (mA) code
420
0.970
330 Violet
400
1.05
330 Gray
200
1.15
300 White
340
1.20
300 Black
330
1.35
300 Brown
310
1.80
260 Red
290
2.45
190 Orange
250
2.80
190 Yellow
230
3.20
180 Green
190
4.10
150 Blue
180
5.30
140 Violet
165
5.90
130 Gray
150
7.00
120 White
135
9.10
110 Black
1. When ordering, please specify termination and packaging code:
0603HL-332XJRC
Termination: R = RoHS compliant matte tin over nickel over silverplatinum-glass frit Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead.
2. Inductance measured at 0.1Vrms, using a Coilcraft SMD-A fixture in Agilent/HP 4287A impedance analyzer or equivalent with Coilcraftprovided correlation pieces.
3. Q measured using a Coilcraft SMD-A fixture in Agilent/HP 4287A impedance analyzer or equivalent.
4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft SMD‑D test fixture.
5. DCR measured on CambridgeTechnology Micro-ohmmeter or equivalent.
6. Current that causes a 15°C temperature rise from 25°C ambient. This information is for reference only and does not represent absolute maximum ratings.
7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Designer’s Kit C449 contains 10 of each value Core material Ceramic Environmental RoHS compliant without exemption, halogen free Terminations RoHS compliant matte tin over nickel over silver-platinum-glass frit. Other terminations available at additional cost. Weight 3.2 – 4.4 mg Ambient temperature –40°C to +125°C with Irms current Maximum part temperature +140°C (ambient + temp rise). Storage temperature Component: –40°C to +140°C. Tape & reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Temperature Coefficient of Inductance (TCL) +50 to +150 ppm/°C Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000 per 7″ reel. Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.0 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf.
Document 894-1 Revised 10/12/15
Inductance (nH)
Document 894-2
Chip Inductors – 0603HL Series
Typical L vs Frequency
Typical Q vs Frequency
10,000
25
1000
3300 nH
1800 nH 1000 nH 560 nH 390 nH
100 1
10 100
Frequency (MHz)
1000
Typical Impedance vs Frequency
100 1800 nH
3300 nH 1000 nH 560 nH 390 nH
10
1
0.1 0.01
10
100
Frequency (MHz)
1000
Q Factor
20
15
10 560 nH 390 nH
1000 nH 5 1800 nH
3300 nH 0
1 10 100 1000
Frequency (MHz)
B overall
F
C D
H
I
AG
J
F
E terminal
Terminal wraparound: approx 0.01/0,25 both ends
I
Recommended Land Pattern
A B C max max max D E F G H I J 0.071 0.047 0.037 0.010 0.030 0.011 0.038 0.040 0.025 0.025 inches 1,80 1,19 0,94 0,25 0,76 0,28 0,97 1,02 0,64 0,64 mm
Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm.
Impedance (kOhms)
Document 894-2 Revised 10/12/15
.