Document
Document 781-1
FerriteChipInductors– 0805AF (2012)
• Higher inductance values than ceramic 0805 inductors • Inductance values from 0.11 µH to 22 µH
• Heavier guage wire for low DCR • Ferrite construction for high current handling
Inductance2
Part number1
±5% (µH) Q typ3
0805AF-111XJR_ 0.11 @ 7.9 MHz
18 @ 7.9 MHz
0805AF-681XJR_ 0.68 @ 7.9 MHz 0805AF-102XJR_ 1.0 @ 7.9 MHz
19 @ 7.9 MHz 17 @ 7.9 MHz
0805AF-122XJR_ 0805AF-152XJR_
1.2 @ 7.9 MHz 1.5 @ 7.9 MHz
19 @ 7.9 MHz 20 @ 7.9 MHz
0805AF-182XJR_ 0805AF-222XJR_
1.8 @ 7.9 MHz 2.2 @ 7.9 MHz
20 @ 7.9 MHz 19 @ 7.9 MHz
0805AF-272XJR_ 0805AF-332XJR_
2.7 @ 7.9 MHz 3.3 @ 7.9 MHz
19 @ 7.9 MHz 19 @ 7.9 MHz
0805AF-472XJR_ 4.7 @ 7.9 MHz
18 @ 7.9 MHz
0805AF-682XJR_ 0805AF-103XJR_ 0805AF-153XJR_
6.8 @ 7.9 MHz 10 @ 2.5 MHz 15 @ 2.5 MHz
18 @ 7.9 MHz 18 @ 2.5 MHz 17 @ 2.5 MHz
0805AF-223XJR_
22 @ 2.5 MHz
17 @ 2.5 MHz
Impedance typ (Ohms)
370 @ 500MHz 430 @ 100 MHz 670 @ 100 MHz 860 @ 100 MHz 1000 @ 100 MHz
1360 @ 100 MHz 840 @ 50 MHz
1050 @ 50MHz 1670 @ 50 MHz
950 @ 25 MHz
450 @ 10MHz 740 @ 10 MHz 1300 @ 10MHz 1620 @ 10 MHz
SRF typ4 DCR max5 Irms6 Color (MHz) (Ohms) (mA) code
1260
0.05
940 Brown
425
0.30
660 Orange
355
0.39
650 Yellow
375
0.64
440 Brown
285
0.74
390 Green
300
0.98
370 Blue
105
0.98
350 Brown
100
1.16
320 Violet
85
1.20
330 Gray
55
1.50
280 Black
37
1.90
240 Brown
26
2.20
230 Red
20
4.25
150 Yellow
21
6.70
120 Green
1. When ordering, please specify termination and packaging codes:
0805AF-103XJRC
Termination: R = RoHS compliant matte tin over nickel over silverplatinum-glass frit. Special order: Q = RoHS tin-silver-copper (95.5/4/0.5) or P = non-RoHS tin-lead (63/37).
Packaging: C = 7″ machine-ready reel. EIA-481 embossed plastic tape (2000 parts per full reel).
B = Less than full reel. In tape, but not machine ready. To have a leader and trailer added ($25 charge), use code letter C instead.
2. Inductance measured at 0.1 Vrms, using Coilcraft SMD-A fixture in Agilent/HP 4286A impedance analyzer with Coilcraft-provided correlation pieces.
3. Q measured on Agilent/HP 4395A with Agilent/HP 16193 test fixture. 4. SRF measured using Agilent/HP 8753D network analyzer with Coilcraft
SMD‑D test fixture. 5. DCR measured on Cambridge Technology Micro-ohmmeter. 6. Current that causes a 15°C temperature rise from 25°C ambient. This
information is for reference only and does not represent absolute maximum ratings. Click for temperature derating information. 7. Electrical specifications at 25°C. Refer to Doc 362 “Soldering Surface Mount Components” before soldering.
Designer’s Kit C450 contains 10 of each value Core material Ferrite Environmental RoHS compliant without exemption, halogen free Terminations RoHS compliant matte tin over nickel over silverplatinum-glass frit. Other terminations available at additional cost. Weight 16.7 – 18.0 mg Ambient temperature –40°C to +85°C with Irms current Maximum part temperature +100°C (ambient + temp rise). Derating. Storage temperature Component: –40°C to +100°C. Tape and reel packaging: –40°C to +80°C Resistance to soldering heat Max three 40 second reflows at +260°C, parts cooled to room temperature between cycles Moisture Sensitivity Level (MSL) 1 (unlimited floor life at <30°C / 85% relative humidity) Failures in Time (FIT) / Mean Time Between Failures (MTBF) One per billion hours / one billion hours, calculated per Telcordia SR-332 Packaging 2000/7″reel; Plastic tape: 8 mm wide, 0.23 mm thick, 4 mm pocket spacing, 1.65 mm pocket depth PCB washing Tested to MIL-STD-202 Method 215 plus an additional aqueous wash. See Doc787_PCB_Washing.pdf.
Document 781-1 Revised 10/12/15
Inductance (µH) Q Factor
Document 781-2
Ferrite Chip Inductors – 0805AF Series
Typical L vs Frequency
100 22 µH
10 µH 6.8 µH 4.7 µH
10 3.3 µH 2.7 µH 2.2 µH 1.5 µH 1.0 µH 0.68 µH
1
Typical Q vs Frequency
30
25 22 µH
20
15
6.8 µH 2.2 µH
0.11 µH 0.68 µH
3.3 µH
1.5 µH
4.7 µH
1.0 µH
10 10 µH 2.7 µH
0.1 1
10 100
Frequency (MHz)
0.11 µH 1000
5 0
1
10 100
Frequency (MHz)
1000
Typical Impedance vs Frequency
1000
100
10
1
0.1
0.01 0.001
0.01 0.1
Frequency (GHz)
1
B overall A
F G F
C D
Pick and place material
I J
I
H
E terminal
Terminal wraparound: approx 0.008/0,20 both ends
Recommended Land Pattern
A B C D max max max ref E F G H I J 0.090 0.068 0.060 0.020 0.050 0.016 0.040 0.070 0.040 0.030 inches 2,29 1,73 1,52 0,51 1,27 0,41 1,02 1,78 1,02 0,76 mm
Note: Height dimension (C) is before optional solder application. For maximum height dimension including solder, add 0.006 in / 0,152 mm.
10
Impedance (kOhms)
22 µH 10 µH 6.8 µH 4.7 µH 3.3 µH 2.7 µH 2.2 µH 1.5 µH 1.0 µH 0.68 µH 0.11 µH
Document 781-2 Revised 10/12/15
.