Document
NSNJ2006 Jun. 2015
New JRC SAW FILTER
NSNJ2006
Application Low Power Transceiver f0=465MHz BW=6MHz
Electrical Specification: (Table 1) The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
Typ.
Input and Output Impedance
- 50
Nominal Center Frequency (f0)
- 465MHz
Insertion Loss
462 468MHz
3.5dB max.
2.9dB
Response Variation 462 468MHz
1.5dB max.
0.7dB
VSWR
462 468MHz
2.0 max.
1.6
Out of Band Rejection (Relative to
Through Level)
419.2 440.9 504.8
425.2MHz
45dB min.
55dB
446.9MHz
45dB min.
54dB
510.8MHz
45dB min.
59dB
(Operating Temperature Range: -20~+60ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings Item Maximum Input Power Maximum DC Voltage Operating Temperature Range Storage Temperature
Rating
+20dBm 7.5V -20~+60ºC -30~+85ºC
Mechanical Specifications: (Fig.2) Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice: This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html Japanese http://www.njr.com/products/device/index.html English
NSNJ2006 Jun. 2015
16 IN 2 SAW 5 50 3 4
OUT 50
Fig.1 Measuring circuit
(a) 3. 0±0. 15 ( b)
3. 0 ± 0. 1 5
560
RJ
( c) ( 1)
1. 1 5 ± 0. 1 5
( 2)
( 0. 6)
34
2
( 1. 80)
1
5 6
( 0. 45)
( 0. 75) [ 4x]
Fig.2 Package dimensions (in mm)
3.8
2.2 1.15
( 0. 2 5) ( 0. 6) [ 2 x]
( 0. 5 3) [ 4x]
Marking (1) Lot Number
(a) Year (b) Month
*Oct.--Nov.--Dec.--(c) Date
1-9--10-19--20-31--(2) Part Number Mark
X Y Z
0 1 2
Pin no. 1 2 3 4 5 6
Connection GND
IN/OUT GND GND
OUT/IN GND
1.15
3.8 0.93 0.6 0.93
Fig.3 Desirable land area (in mm)
NSNJ2006 Jun. 2015
Notice
1. Use this component within operating temperature range. It might not be satisfied with electrical specification without operating temperature range. When it is used less than -20ºC or more than +60ºC, it might be a cause of degradation or destruction of the component. Even if it endures during a short time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering iron: 350ºC max., the time of soldering: 10 seconds max., the power of soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a cause of destruction clean this component after confirming that temperature of this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to this component, do not apply static electricity or excessive voltage while assembling and measuring. And do not transport this component with bare hand.
7. As it might be a cause o.