Operational Amplifier. NJU7036 Datasheet

NJU7036 Amplifier. Datasheet pdf. Equivalent

NJU7036 Datasheet
Recommendation NJU7036 Datasheet
Part NJU7036
Description Dual CMOS Operational Amplifier
Feature NJU7036; NJU7036 High Output Current, Single Supply, Rail-to-Rail Output Dual CMOS Operational Amplifier GEN.
Manufacture New Japan Radio
Datasheet
Download NJU7036 Datasheet




New Japan Radio NJU7036
NJU7036
High Output Current, Single Supply, Rail-to-Rail Output
Dual CMOS Operational Amplifier
GENERAL DESCRIPTION
The NJU7036 is a Rail-to-Rail Output operational amplifier of single power supply operation.
It has the characteristic of high power output current and is suitable for driving heavy loads such as a small motor, LED, and speakers.
It has up to 0.15 V saturation voltages at an output current of 250mA.
Therefore it can reduce the electric power loss in IC and contribute to the design of low power consumption.
Moreover, micro leadless package (PCSP20-E3) is available for it, so that it can also contribute to the miniaturization of the equipment.
FEATURES
•Rail-to-Rail Output
Vo=4.7Vpp min. at VDD= 5V,Io=250mA
•Single Supply
•Operating Voltage
Vopr= 2.7V to 5.5V
• Package Outline
PCSP20-E3
CMOS Process
• Thermal Shutdown Circuit
• Current Limit Circuit
PACKAGE OUTLINE
NJU7036SE3
(PCSP20-E3)
APPLICATION
•Motor Drivers , Audio Amplifiers , LED Drivers , etc.
PIN CONFIGURATION (Top View)
NJU7036SE3
1,2 A OUTPUT
3,4 VSS
5 NC
6 A -INPUT
7 A +INPUT
8 NC
9 B +INPUT
10
11
12,13
14,15
16,17
18,19
20
B -INPUT
NC
VSS
B OUTPUT
NC
VDD
NC
VDD terminal, VSS terminal and OUTPUT terminal use two or more pins respectively and are lowering terminal resistance.
You shall connect each two pins (VDD, VSS and OUTPUT) with the same electric potential.
When only one pin is used, the internal terminal resistance becomes high and the maximum output voltage declines.
E3 20091125
-1-



New Japan Radio NJU7036
NJU7036
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Supply Voltage
VDD
Power Dissipation
PD
Output Peak Current
Input Common Mode Voltage
Differential Input Voltage
Operating Temperature Range
Storage Temperature Range
IOP
VICM
VID
Topr
Tstg
RATINGS
7.0
Ta=25˚C
UNIT
V
PCSP20(The back pad is mounted.) : 560 *1), 980 *2)
(The back pad is not mounted.): 550 *1), 850 *2)
mW
500
-0.3 to 7.0 *3)
±7 *3)
-40 to +85
-55 to +150
mA
V
V
˚C
˚C
*1 ) EIA/JEDEC STANDARD Test board (76.2 x 114.3 x 1.6mm, 4layers, FR-4) mounting
*2 ) EIA/JEDEC STANDARD Test board (76.2 x 114.3 x 1.6mm, 2layers, FR-4) mounting
*3) If the supply voltage VDD is less than 7V, the input voltage must not over the VDD level through 7V is limit specified.
RECOMMENDED OPERATING CONDITION
PARAMETER
SYMBOL
Supply Voltage
VDD
RATING
2.7 to 5.5
Ta=25˚C
UNIT
V
ELECTRICAL CHARACTERISTICS
/2),Ta=25˚C
PARAMETER
SYMBOL
l DC CHARACTERISTICS
Maximum Output Voltage
*RL=OPEN
VOH1
VOH2
VOH3
VOL1
VOL2
VOL3
Input Offset Voltage
Vio
Input Bias Current
IB
Input Offset Current
IIO
Large Signal Voltage Gain
AV
Common Mode Rejection Ratio
CMR
Supply Voltage Rejection Ratio
SVR
Input Common Mode Voltage Range
VICM
Operating Current
IDD
l AC CHARACTERISTICS
Unity Gain Bandwidth
fT
Equivalent Input Noise Voltage
VNI
Total Harmonic Distortion
(THD+N)
Output Power
THD
Po
VDD=5V,
VSS=0V,VIC=2.5V,RL=8(connected
TEST CONDITION
MIN TYP MAX
Isource=250mA
Isource=150mA
Isource=50mA
Isink=250mA
Isink=150mA
Isink=50mA
Vo= VDD /2±2V
VICM=0V to 3.8V
VDD =2.7V to 5.5V
CMR60dB
No Signal,RL=open
4.85
4.88
4.92
-
-
-
-
-
-
80
60
60
0
-
4.90
4.94
4.98
0.10
0.06
0.02
2
1
1
100
80
80
-
3.5
-
-
-
0.15
0.12
0.08
10
-
-
-
-
-
3.8
5.3
VDD
UNIT
V
V
V
V
V
V
mV
pA
pA
dB
dB
dB
V
mA
GV=6dB, CL=10pF
f=1kHz, GV=6dB,
Rs=100,
GV=6dB, CL=10pF
fin=1kHz, Po=250mW
GV=6dB, CL=10pF
fin=1kHz, THD5%
- 0.4 - MHz
- 60 - nV/Hz
- 0.03 -
%
- 400 - mW
-2-
E3 20091125



New Japan Radio NJU7036
NJU7036
Channel Separasion
CS f=1kHz
- 90 - dB
PARAMETER
SYMBOL
TEST CONDITION
MIN
TYP
MAX
UNIT
lTRANSIENT CHARACTERISTICS
Slew Rate
SR
GV=0dB, CL=10pF
Vin=1.0Vpp
-
0.7
- V/µs
PARAMETER
l DC CHARACTERISTICS
Maximum Output Voltage
*RL=OPEN
Input Offset Voltage
Input Bias Current
Input Offset Current
Large Signal Voltage Gain
Common Mode Rejection Ratio
Supply Voltage Rejection Ratio
Input Common Mode Voltage Range
Operating Current
l AC CHARACTERISTICS
Unity Gain Bandwidth
Equivalent Input Noise Voltage
Total Harmonic Distortion
(THD+N)
Output Power
Channel Separasion
lTRANSIENT CHARACTERISTICS
Slew Rate
SYMBOL
VOH1
VOH2
VOH3
VOL1
VOL2
VOL3
Vio
IB
IIO
AV
CMR
SVR
VICM
IDD
fT
VNI
THD
Po
CS
SR
VDD=3V, VSS=0V,VIC=1.5V,RL=8(connected VDD /2),Ta=25˚C
TEST CONDITION
MIN
TYP
MAX
UNIT
Isource=250mA
Isource=150mA
Isource=50mA
Isink=250mA
Isink=150mA
Isink=50mA
Vo= VDD /2±1V
VICM=0V to 1.8V
VDD =2.7V to 3.5V
CMR60dB
No Signal,RL=open
2.77
2.83
2.90
-
-
-
-
-
-
70
60
58
0
-
2.85
2.91
2.97
0.15
0.09
0.03
2
1
1
90
80
70
-
2.4
-
-
-
0.23
0.17
0.10
10
-
-
-
-
-
1.8
3.5
V
V
V
V
V
V
mV
pA
pA
dB
dB
dB
V
mA
GV=6dB, CL=10pF
-
0.4
- MHz
f=1kHz, GV=6dB,
Rs=100,
- 60 - nV/Hz
GV=6dB, CL=10pF
fin=1kHz, Po=60mW
- 0.06 -
%
GV=6dB,C L = 1 0 p F
fin=1kHz, THD5%
- 150 - mW
f=1kHz
- 90 - dB
GV=0dB, CL=10pF
Vin=0.5Vpp
-
0.5
- V/µs
E3 20091125
-3-







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)