Document
Datasheet Values Refer to PCN-OPT-1224-2022
www.vishay.com
TSOP22.., TSOP24.., TSOP48.., TSOP44..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
23196
LINKS TO ADDITIONAL RESOURCES
Product Page
Marking
Packages
Holders
Bends and Cuts
DESCRIPTION
This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications.
FEATURES • Individual IC settings to reach maximum
performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization:
for definitions of compliance please see www.vishay.com/doc?99912
APPLICATIONS • Infrared remote control systems
DESIGN SUPPORT TOOLS • 3D models • Window size calculator
BLOCK DIAGRAM
30 kΩ
Input
AGC
Band pass
Demodulator
PIN
16833-22
Control circuit
VS OUT GND
Rev. 2.3, 16-Aug-2022
1
Document Number: 82459
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
www.vishay.com
TSOP22.., TSOP24.., TSOP48.., TSOP44..
Vishay Semiconductors
MECHANICAL DATA Pinning for TSOP44.., TSOP48..: 1 = OUT, 2 = GND, 3 = VS Pinning for TSOP22.., TSOP24..: 1 = OUT, 2 = VS, 3 = GND
ORDERING CODE TSOP2..., TSOP4... - 2160 pieces in tubes
APPLICATION CIRCUIT
17170-14
Transmitter IR receiver
with TSALxxxx
VS
Circuit
OUT GND
R1
C1 VO
+ VS µC
GND
1 2 3
23198
R1 and C1 recommended in case there are strong ripple or spikes on the supply line.
PARTS TABLE
AGC
30 kHz
33 kHz
Carrier
36 kHz
frequency 38 kHz
40 kHz
56 kHz
Package
Pinning
Dimensions (mm)
Mounting
Application
Best choice for
Special options
LEGACY, FOR LONG BURST REMOTE CONTROLS (AGC2)
RECOMMENDED FOR LONG BURST CODES (AGC4)
TSOP4830
TSOP2230
TSOP4430
TSOP2430
TSOP4833
TSOP2233
TSOP4433
TSOP2433
TSOP4836
TSOP2236
TSOP4436 (1)(2)(3)
TSOP2436 (1)(2)(3)
TSOP4838
TSOP2238
TSOP4438 (4)(5)(6)(9)(10)
TSOP2438 (4)(5)(6)(9)(10)
TSOP4840 (8)
TSOP2240 (8)
TSOP4440
TSOP2440
TSOP4856 (11)
TSOP2256 (11)
TSOP4456 (6)(7)
TSOP2456 (6)(7)
Mold
1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 1 = OUT, 2 = GND, 3 = VS 1 = OUT, 2 = VS, 3 = GND 6.0 W x 6.95 H x 5.6 D
Leaded
Remote control
(1) RC-5 (2) RC-6 (3) Panasonic (4) NEC (5) Sharp (6) r-step (7) Thomson RCA (8) Sony (9) Mitsubishi (10) Sejin 4PPM (11) Cisco
• Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage Supply current Output voltage Voltage at output to supply Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature
Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case
VS
-0.3 to +6
V
IS
5
mA
VO
-0.3 to 5.5
V
VS - VO
-0.3 to (VS + 0.3)
V
IO
5
mA
Tj
100
°C
Tstg
-25 to +85
°C
Tamb
-25 to +85
°C
Ptot
10
mW
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
Rev. 2.3, 16-Aug-2022
2
Document Number: 82459
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
www.vishay.com
TSOP22.., TSOP24.., TSOP48.., TSOP44..
Vishay Semiconductors
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Supply current Supply voltage Transmission distance
Output voltage low
Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
ISD ISH VS
d
VOSL
0.25 -
2.0
-
-
0.35 0.45
-
24
-
0.45 5.5
-
100
Minimum irradiance Maximum irradiance
Test signal: RC5 code
Ee min.
-
Test signal: NEC code
Ee min.
-
tpi - 4/fo < tpo < tpi + 4/fo, test signal see Fig. 1
Ee.