Document
Datasheet Values Refer to PCN-OPT-1225-2022-REV-0
www.vishay.com
TSOP531.., TSOP533.., TSOP535..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
23051
LINKS TO ADDITIONAL RESOURCES
Product Page
Marking
Packages
Holders
Bends and Cuts
DESCRIPTION
This IR receiver series is optimized for short burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. These components have not been qualified to automotive specifications.
FEATURES • Individual IC settings to reach maximum
performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization:
for definitions of compliance please see www.vishay.com/doc?99912
DESIGN SUPPORT TOOLS • 3D models • Window size calculator
APPLICATIONS • Infrared remote control systems
BLOCK DIAGRAM
30 kΩ
Input
AGC
Band pass
Demodulator
PIN
16833-22
Control circuit
VS OUT GND
Rev. 1.8, 17-Jan-2023
1
Document Number: 82745
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1225-2022-REV-0
www.vishay.com
TSOP531.., TSOP533.., TSOP535..
Vishay Semiconductors
MECHANICAL DATA Pinning for TSOP53...: 1 = OUT, 2 = GND, 3 = VS
1 2 3
23197
ORDERING CODE TSOP53... - 1800 pieces in bags
APPLICATION CIRCUIT
17170-14
Transmitter IR receiver
with TSALxxxx
VS
Circuit
OUT GND
R1
C1 VO
+ VS µC
GND
R1 and C1 recommended in case there are strong ripple or spikes on the supply line.
PARTS TABLE
AGC
Carrier frequency
Package Pinning Dimensions (mm) Mounting Application Best choice for
30 kHz 33 kHz 36 kHz 38 kHz 40 kHz 56 kHz
Special options
LEGACY, FOR SHORT BURSTS FOR SHORT BURSTS, NOISY FOR SHORT BURSTS, VERY
(AGC1)
ENVIRONMENTS (AGC3) NOISY ENVIRONMENTS (AGC5)
TSOP53130
TSOP53330
TSOP53530
TSOP53133
TSOP53333
TSOP53533
TSOP53136
TSOP53336 (1)(2)
TSOP53536
TSOP53138
TSOP53338 (3)(5)
TSOP53538
TSOP53140
TSOP53340
TSOP53540
TSOP53156
TSOP53356 (4)
TSOP53556
Minimold
1 = OUT, 2 = GND, 3 = VS 5.4 W x 6.35 H x 4.9 D
Leaded
Remote control
(1) MCIR (2) RCMM (3) RECS-80 Code (4) r-map (5) XMP
• Narrow optical filter: www.vishay.com/doc?81590 • Wide optical flter: www.vishay.com/doc?82726
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
VS
-0.3 to +6
V
Supply current
IS
5
mA
Output voltage
VO
-0.3 to 5.5
V
Voltage at output to supply
VS - VO
-0.3 to (VS + 0.3)
V
Output current
IO
5
mA
Junction temperature
Tj
100
°C
Storage temperature range
Tstg
-25 to +85
°C
Operating temperature range
Tamb
-25 to +85
°C
Power consumption
Tamb ≤ 85 °C
Ptot
10
mW
Soldering temperature
t ≤ 10 s, 1 mm from case
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
Rev. 1.8, 17-Jan-2023
2
Document Number: 82745
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1225-2022-REV-0
www.vishay.com
TSOP531.., TSOP533.., TSOP535..
Vishay Semiconductors
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
Supply current Supply voltage Transmission distance Output voltage low
Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
ISD ISH VS d
VOSL
0.25 -
2.0 -
-
0.35 0.45
24
-
0.45 -
5.5 -
100
Minimum irradiance
Maximum irradiance Directivity
Test signal: RC5 code
Ee min.
-
Test signal: XMP code
Ee min.
-
tpi - 3/fo < tpo < tpi + 3.5/fo, test signal see Fig. 1 Ee max.
50
Angle of half transmission distance
ϕ1/2
-
0.12
0.25
0.2
0.4
-
-
± 45
-
UNIT mA mA V
m
mV
mW/m2 mW/m2 W/m2
deg
TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
Ee
Optical Test Signal (IR diode TSAL6200, N = 6 pulses, f = f0, T = 10 ms)
Op.