Microcontroller. ATSAMD10D14A-MNT Datasheet

ATSAMD10D14A-MNT Microcontroller. Datasheet pdf. Equivalent


Part ATSAMD10D14A-MNT
Description Microcontroller
Feature SMART Atmel SAM D10 SMART ARM-Based Microcontroller Description DATASHEET The Atmel® | SMART™ SA.
Manufacture Atmel
Datasheet
Download ATSAMD10D14A-MNT Datasheet


SMART Atmel SAM D10 SMART ARM-Based Microcontroller Descri ATSAMD10D14A-MNT Datasheet
Recommendation Recommendation Datasheet ATSAMD10D14A-MNT Datasheet




ATSAMD10D14A-MNT
SMART
Atmel SAM D10
SMART ARM-Based Microcontroller
Description
DATASHEET
The Atmel® | SMARTSAM D10 is a series of low-power microcontrollers using the 32-bit
ARM® Cortex®-M0+ processor, and ranging from 14- to 24-pins with up to 16KB Flash and 4KB of
SRAM. The SAM D10 devices operate at a maximum frequency of 48MHz and reach
2.46 Coremark/MHz. They are designed for simple and intuitive migration with identical
peripheral modules, hex compatible code, identical linear address map and pin compatible
migration paths between all devices in the product series. All devices include intelligent and
flexible peripherals, Atmel Event System for inter-peripheral signaling, and support for capacitive
touch button, slider and wheel user interfaces. The SAM D10 series is compatible to the other
product series in the SAM D family, enabling easy migration to larger device with added features.
The Atmel SAM D10 devices provide the following features: In-system programmable Flash, six-
channel direct memory access (DMA) controller, 6 channel Event System, programmable
interrupt controller, up to 22 programmable I/O pins, 32-bit real-time clock and calendar, two 16-
bit Timer/Counters (TC) and one 24-bit Timer/Counter for Control (TCC), where each TC can be
configured to perform frequency and waveform generation, accurate program execution timing or
input capture with time and frequency measurement of digital signals. The TCs can operate in 8-
or 16-bit mode, selected TCs can be cascaded to form a 32-bit TC, and one timer/counter has
extended functions optimized for motor, lighting and other control applications. The series provide
up to three Serial Communication Modules (SERCOM) that each can be configured to act as an
USART, UART, SPI, I2C up to 3.4MHz, SMBus, PMBus and LIN slave; up to 10-channel 350ksps
12-bit ADC with programmable gain and optional oversampling and decimation supporting up to
16-bit resolution, one 10-bit 350ksps DAC, two analog comparators with window mode,
Peripheral Touch Controller supporting up to 72 buttons, sliders, wheels and proximity sensing;
programmable Watchdog Timer, brown-out detector and power-on reset and two-pin Serial Wire
Debug (SWD) program and debug interface.
All devices have accurate and low-power external and internal oscillators. All oscillators can be
used as a source for the system clock. Different clock domains can be independently configured
to run at different frequencies, enabling power saving by running each peripheral at its optimal
clock frequency, and thus maintaining a high CPU frequency while reducing power consumption.
The SAM D10 devices have two software-selectable sleep modes, idle and standby. In idle mode
the CPU is stopped while all other functions can be kept running. In standby all clocks and
functions are stopped expect those selected to continue running. The device supports
SleepWalking. This feature allows the peripheral to wake up from sleep based on predefined
conditions, and thus allows the CPU to wake up only when needed, e.g. when a threshold is
crossed or a result is ready. The Event System supports synchronous and asynchronous events,
allowing peripherals to receive, react to and send events even in standby mode.
The Flash program memory can be reprogrammed in-system through the SWD interface. The
same interface can be used for non-intrusive on-chip debug and trace of application code. A boot
loader running in the device can use any communication interface to download and upgrade the
application program in the Flash memory.
The Atmel SAM D10 devices are supported with a full suite of program and system development
tools, including C compilers, macro assemblers, program debugger/simulators, programmers and
evaluation kits.
Atmel-42242H-SAM-D10-Datasheet_09/2016



ATSAMD10D14A-MNT
Features
z Processor
z ARM Cortex-M0+ CPU running at up to 48MHz
z Single-cycle hardware multiplier
z Micro Trace Buffer
z Memories
z 8/16KB in-system self-programmable Flash
z 4KB SRAM Memory
z System
z Power-on reset (POR) and brown-out detection (BOD)
z Internal and external clock options with 48MHz Digital Frequency Locked Loop (DFLL48M) and 48MHz to 96MHz Fractional
Digital Phase Locked Loop (FDPLL96M)
z External Interrupt Controller (EIC)
z 8 external interrupts
z One non-maskable interrupt
z Two-pin Serial Wire Debug (SWD) programming, test and debugging interface
z Low Power
z Idle and standby sleep modes
z SleepWalking peripherals
z Peripherals
z 6-channel Direct Memory Access Controller (DMAC)
z 6-channel Event System
z Two 16-bit Timer/Counters (TC), configurable as either:
z One 16-bit TC with compare/capture channels
z One 8-bit TC with compare/capture channels
z One 32-bit TC with compare/capture channels, by using two TCs
z One 24-bit Timer/Counters for Control (TCC), with extended functions:
z Up to four compare channels with optional complementary output
z Generation of synchronized pulse width modulation (PWM) pattern across port pins
z Deterministic fault protection, fast decay and configurable dead-time between complementary output
z Dithering that increase resolution with up to 5 bit and reduce quantization error
z 32-bit Real Time Counter (RTC) with clock/calendar function
z Watchdog Timer (WDT)
z CRC-32 generator
z Up to three Serial Communication Interfaces (SERCOM), each configurable to operate as either:
z USART with full-duplex and single-wire half-duplex configuration
z I2C Bus up to 3.4MHz
z SMBUS/PMBUS
z SPI
z LIN slave
z 12-bit, 350ksps Analog-to-Digital Converter (ADC) with up to 10 channels
z Differential and single-ended input
z 1/2x to 16x programmable gain stage
z Automatic offset and gain error compensation
z Oversampling and decimation in hardware to support 13-, 14-, 15- or 16-bit resolution
z 10-bit, 350ksps Digital-to-Analog Converter (DAC)
z Two Analog Comparators (AC) with window compare function
z Peripheral Touch Controller (PTC)
z Up to 72-channel capacitive touch and proximity sensing
z I/O
z Up to 22 programmable I/O pins
z Packages
z 24-pin QFN
z 20-pin SOIC
z 20-ball WLCSP
z 14-pin SOIC
z Operating Voltage
z 1.62V – 3.63V
Atmel | SMART SAM D10 [DATASHEET]
Atmel-42242H-SAM-D10-Datasheet_09/2016
2







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)