Blower. 9BMC24P2G001 Datasheet

9BMC24P2G001 Blower. Datasheet pdf. Equivalent

Part 9BMC24P2G001
Description Blower
Feature Blower 9BMC type Features High Airflow The maximum airflow has increased by 15% compared with our .
Manufacture Sanyo Denki
Datasheet
Download 9BMC24P2G001 Datasheet

Blower 9BMC type Features High Airflow The maximum airflow 9BMC24P2G001 Datasheet
Recommendation Recommendation Datasheet 9BMC24P2G001 Datasheet





9BMC24P2G001
Blower
9BMC type
Features
High Airflow
The maximum airflow has increased by 15% compared with our
current model.*
High Static Pressure
The maximum static pressure has increased by 50% compared
with our current model.*
Low Noise and High Energy Efficiency
The PWM control function enables the external control of fan
speed, contributing to lower noise and higher energy efficiency of
devices.
* New model 9BMC12P2G001 compared with our current blower model 9BMB12P2K01,
97 × 33 mm San Ace B97 9BMB type.
97 33 mm
Specifications
The following nos. have PWM controls, pulse sensors.
Model no.
9BMC12P2G001
9BMC24P2G001
Rated voltage
[V]
Operating
voltage range
[V]
12 10.8 to 13.2
24 21.6 to 26.4
PWM
duty cycle*
[%]
100
20
100
20
Rated current Rated input Rated speed Max. airflow Max. static pressure
[A] [W] [min-1] [m3/min] [CFM] [Pa] [inchH2O]
6.2 74.4
8200 1.85 65.3 1950 7.83
0.38 4.56 2800 0.58 20.4 121.0 0.48
3.1 74.4
8200 1.85 65.3 1950 7.83
0.19 4.56 2800 0.58 20.4 121.0 0.48
SPL
[dB(A)]
69
44
69
44
Operating Expected
temperature life
[°C] [h]
-20 to +70
40000/60°C
(70000/40°C)
PWM frequency: 25 kHz. Fan does not rotate when PWM duty cycle is 0%.
Models with the following sensor specifications are also available as options: Without sensor Pulse sensor
Please inquire as the availability of these options depends on the model: Lock sensor
Common Specifications
Material
Expected life
Motor protection system
Dielectric strength
Sound pressure level (SPL)
Operating temperature
Storage temperature
Lead wire
Mass
Frame, Impeller: Plastics (Flammability: UL 94V-0)
Refer to specifications
(L10: Survival rate: 90% at 60°C, rated voltage, and continuously run in a free air state)
Expected life at 40°C ambient is just reference value.
Current blocking function and reverse polarity protection
50/60 Hz, 500 VAC, 1 minute (between lead conductor and frame)
Expressed as the value at 1 m from air inlet side
Refer to specifications (Non-condensing)
-30 to +70°C (Non-condensing)
Red Black Sensor: Yellow Control: Brown
Approx. 200 g
Airflow - Static Pressure Characteristics
PWM duty cycle
(inch H2O) (Pa)
8 2000
7
6 1500
5
12/24 VDC
PWM duty cycle
100%
Operating voltage range
(inch H2O) (Pa)
8 2000
7
PWM duty cycle 100%
12 V/13.2 V
24 V/26.4 V
6 1500
5
10.8 V/21.6 V
4 1000
3
60%
4 1000
3
2 500
1
20%
2 500
1
PWM Duty
- Speed Characteristics Example
(min-1)
9000
8000
7000
6000
5000
4000
3000
2000
1000
Voltage: 12 VDC/24 VDC
PWM frequency: 25 kHz
8200 min-1
00
0.5 1.0 1.5 2.0 (m3/min) 0 0
0.5 1.0 1.5 2.0 (m3/min)
0 10 20 30 40 50 60 70 (CFM)
Airflow
0 10 20 30 40 50 60 70 (CFM)
Airflow
0 100 (%)
PWM duty cycle



9BMC24P2G001
PWM Input Signal Example
Input signal waveform
VIH
VIL
T1
T
VIH=4.75 to 5.25 V VIL=0 to 0.4 V
PWM
duty
cycle
(%)
=
T1
T
×100
PWM frequency
25
(kHz)
=
1
T
Current source (Isource) =1 mA max. (when control voltage is 0 V)
Current sink (Isink) =1 mA max. (when control voltage is 5.25 V)
Control terminal voltage =5.25 V max. (when control terminal is open)
When the control terminal is open,
fan speed is the same as when PWM duty cycle is 100%.
Either TTL input, open collector or open drain can be used for
PWM control input signal.
Example of Connection Schematic
DC fan input voltage
Inside of DC fan
Control
PWM input signal
Isource
Isink
5V
10 kΩ
22 Ω
20 kΩ
DC fan input voltage
Control
PWM input signal
Isource
Isink
Inside of DC fan
15 V
10 kΩ
22 Ω
20 kΩ
Rated voltage 12 V fan
Rated voltage 24 V fan
Specifications for Pulse Sensors
Output circuit: Open collector
Inside of DC fan
Output waveform (Need pull-up resistor)
In case of steady running
Sensor Pull-up resistor
Pull-up voltage
(One revolution)
T0
Ic Rated voltage 12 V fan
T1 T2 T3 T4
Sensor output
(VCE)
VCE=+13.8 V max.
Ic=5 mA max.[VOL=VCE (SAT) =0.6 V max.]
VOH
Rated voltage 24 V fan
VCE=+26.4 V max.
VOL
Ic=10 mA max.[VOL=VCE (SAT) =1.0 V max.]
0V
T1 to 4 (1/4) T0
T1 to 4 (1/4) T0=60/4N (s)
N=Fan speed (min-1)
Dimensions (unit: mm)
(2.4)
33±1
(1.5)
97.1±1
(50) 39±0.3
(21) (10)
31.5±0.3
4- 4.5±0.3
Mounting hole
Lead wire
Rated voltage 12 V fan
AWG 20
UL 1430
Rated voltage 24 V fan
AWG 24
UL 1430
300±30
56±1
(10) (5)
26±0.3
32±0.3
Rotating direction
Airflow direction
Notice
Please read the "Safety Precautions" on our website before using the product.
The products shown in this catalog are subject to Japanese Export Control Law. Diversion contrary to the law of exporting country is prohibited.
For protecting fan bearings against electrolytic corrosion near strong electromagnetic noise sources,
we provide effective countermeasures such as Electrolytic Corrosion Proof Fans and EMC guards. Contact us for details.
3-33-1, Minami-Otsuka, Toshima-ku, Tokyo 170-8451, Japan TEL: +81 3 5927 1020
https://www.sanyodenki.com
The names of companies and/or their products specified in this catalog are the trade names, and/or trademarks and/or registered trademarks of such respective companies.
“San Ace” is a trademark of SANYO DENKI CO.,LTD.
Specifications are subject to change without notice.
CATALOG No. C1069B002 ‘17.8





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)