Power Switch. DP2539A Datasheet

DP2539A Switch. Datasheet pdf. Equivalent


DEVELOPER MICROELECTRONICS DP2539A
DP2539A
High Precision CC/CV Primary-Side PWM Power Switch
GENERAL DESCRIPTION
DP2539A is a high performance offline PWM
power switch for low power AC/DC charger and
adapter applications. It operates in primary-side
sensing and regulation. Consequently,
opto-coupler and TL431 could be eliminated. High
Precision Constant Voltage (CV) and Constant
Current (CC) control are integrated as shown in
the figure below.
In CC control, the current and output power setting
can be adjusted externally by the sense resistor Rs
at CS pin. In CV control, multi-mode operations are
utilized to achieve high performance and high
efficiency. In addition, good load regulation is
achieved by the built-in Cable Drop Compensation.
Device operates in PFM in CC mode as well at
large load condition and it operates in PWM with
frequency reduction at light/medium load. The chip
consumes very low operation current, it can
achieve less than 75mW standby power.
DP2539A offers comprehensive protection
coverage with auto-recovery features including
Cycle-by-Cycle current limiting, VDD Over Voltage
Protection (VDD OVP), short circuit protection,
built-in leading edge blanking, VDD under voltage
lockout (UVLO), OTP, etc.
High precision constant voltage (CV) and constant
current (CC) can be achieved by DP2539A.
DP2539A is offered in DIP8 package.
TYPICAL APPLICATION
FEATURES
± 5% Constant Voltage Regulation and
Current Regulation at Universal AC Input
Primary Side Regulation (PSR) Without TL431
and Opto-coupler
No Need for Control Loop Compensation
Programmable CV and CC Regulation
Multi-Mode PWM/PFM Operation
Output Short Load Protection
Less than 75mW Standby Power
Built-in Line Voltage and Primary Winding
Inductance Compensation
Built-in Adaptive Current Peak Regulation
Programmable Cable Drop Compensation
Audio Noise Free Operation
Built-in Over Temperature Protection (OTP)
Soft Gate Driver for Good EMI Performance
Built-in Leading Edge Blanking (LEB)
Cycle-by-Cycle Current Limiting
VDD Under Voltage Lockout with Hysteresis
(UVLO)
VDD OVP & Clamp
APPLICATIONS
Low Power AC/DC offline SMPS for
Cell Phone Charger
Digital Camera Charger
Small Power Adapter
Auxiliary Power for PC, TV etc.
Linear Regulator/RCC Replacement
www.depuw.com
- 1 -/9
REV1.0


DP2539A Datasheet
Recommendation DP2539A Datasheet
Part DP2539A
Description High Precision CC/CV Primary-Side PWM Power Switch
Feature DP2539A; DP2539A High Precision CC/CV Primary-Side PWM Power Switch GENERAL DESCRIPTION DP2539A is a high pe.
Manufacture DEVELOPER MICROELECTRONICS
Datasheet
Download DP2539A Datasheet




DEVELOPER MICROELECTRONICS DP2539A
DP2539A
High Precision CC/CV Primary-Side PWM Power Switch
GENERAL INFORMATION
Pin Configuration
The pin map of DIP8 package is shown as below.
Ordering Information
Part Number
Description
DP2539A
DIP8, Rohs, 50Pcs/Tube
Package Dissipation Rating
Package
DIP8
RJA (/W)
75
Absolute Maximum Ratings
Parameter
Value
Drain Voltage (off state)
-0.3 to 600V
VDD Zener Clamp Voltage
VDD_Clamp
VDD Clamp
Current
Continuous 10 mA
CS Input Voltage
-0.3 to 7V
INV Input Voltage
-0.3 to 7V
Maximum Operating Junction
Temperature TJ
150 oC
Min/Max Storage Temperature
Tstg
-55 to 150 oC
Lead Temperature (Soldering,
10secs)
260 oC
Note: Stresses beyond those listed under “absolute maximum
ratings” may cause permanent damage to the device. These
are stress ratings only, functional operation of the device at
these or any other conditions beyond those indicated under
“recommended operating conditions” is not implied. Exposure
to absolute maximum-rated conditions for extended periods
may affect device reliability.
Output Power Table (1)
Part Number
230VAC ± 15%(2)
85-265VAC
Adapter(3)
Adapter(3)
DP2539A
18W
15W
Note 1. The Max. output power is limited by junction temperature
Note 2. 230VAC or 100/115VAC with doublers
Note 3. Typical continuous power in a non-ventilated enclosed adapter with sufficient drain pattern as a heat sink at 50
ambient.
www.depuw.com
- 2 -/9
REV1.0



DEVELOPER MICROELECTRONICS DP2539A
Marking Information
DP2539A
High Precision CC/CV Primary-Side PWM Power Switch
DPXXXX for product name;The A represents the version
XXXXXX The first X reresents the last year,2014 is 4; The second X represents the month, in
A-L 12 letters;The third and fourth X on behalf of the date, 01-31 said; The last two X represents
the wafer batch code.
TERMINAL ASSIGNMENTS
Pin Num
1
2
3
4
5/6
7/8
Pin Name
VDD
NC
INV
CS
Drain
GND
I/O Description
P Power supply.
- No connect.
I
The voltage feedback from auxiliary winding. Connected to resistor divider
from auxiliary winding reflecting output voltage.
I Current sense input.
O The Power MOSFET Drain
P Ground.
www.depuw.com
- 3 -/9
REV1.0







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)