Op Amps. TP1561N Datasheet

TP1561N Amps. Datasheet pdf. Equivalent

TP1561N Datasheet
Recommendation TP1561N Datasheet
Part TP1561N
Description Op Amps
Feature TP1561N; TP1561/ TP1561N/TP1562/TP1564          Stable 3.8MHz, 130μA, RRIO, EveryCapTM Op Amps Features  St.
Manufacture 3Peak
Datasheet
Download TP1561N Datasheet




3Peak TP1561N
TP1561/ TP1561N/TP1562/TP1564
        
Stable 3.8MHz, 130μA, RRIO, EveryCapTM Op Amps
Features
Stable 3.8 MHz GBWP Over Temperature Range
Stable 3.8 MHz GBWP in VCM from 0-V to VDD
Very Low Supply Current: 130 μA per Amplifier
Unity Gain Stable for Any Capacitive Load
Offset Voltage: 3.0 mV Maximum
Offset Voltage Temperature Drift: 0.6 μV/°C
Input Bias Current: 1 pA Typical
THD+Noise: -115 dB at 1kHz, -99 dB at 10kHz
High CMRR/PSRR: 120 dB
Beyond the Rails Input Common-Mode Range
Outputs Swing to within 5 mV of Each Rail
No Phase Reversal for Overdriven Inputs
Drives 2 kResistive Loads
Shutdown Current: 0.2 μA (TP1561N)
Supply Voltage Range:
- Single +2.1 V to +6.0 V Supply
- Or Dual ±1.05 V to ±3.0 V Supplies
–40°C to 125°C Operation Temperature Range
ESD Rating: 8KV – HBM, 2KV–CDM and 500V–MM
Green, Popular Type Package
Applications
Multimedia Audio
Headphone Drivers
LCD Drivers
Photo Diode Pre-amp
Medical Equipments
Portable Devices
ASIC Input or Output
Sensor Interfaces
Pin Configuration (Top View)
Description
The TP156x series are CMOS single, dual, and
quad RRIO op-amps with low offset, low power and
stable high frequency response. They incorporate
3PEAK’s proprietary and patented design
techniques to achieve very good AC performance
with 3.8MHz bandwidth, 3.6V/μs slew rate and low
distortion while drawing only 130μA of quiescent
current per amplifier. The input common-mode
voltage range extends 300mV beyond Vand V+, and
the outputs swing rail-to-rail. The TP156x family can
be used as plug-in replacements for many
commercially available op-amps to reduce power
and improve input/output range and performance.
The TP156x Op-amps are unity gain stable with any
capacitive load. They operate from either single
+2.1V to +6.0V supply or dual ±1.05V to ±3.0V
supplies. Analog trim and calibration routine reduce
input offset voltage to below 3.0mV, and proprietary
precision temperature compensation technique
makes offset voltage temperature drift at 0.6μV/°C.
Adaptive biasing and dynamic compensation
enables the TP156x to achieve ‘THD +Noise’ for
1kHz/10kHz 2VPP signal at -115dB/ -99dB. Beyond
the rails input and rail-to-rail output characteristics
allow the full power-supply voltage to be used for
signal range.
The combination of features makes the TP156x
ideal choices for audio amplification of computers,
sound ports, and other consumer Audio. The
TP156x Op-amp is very stable, and it is capable of
driving heavy capacitive loads such as those found
in LCDs. The ability to swing rail-to-rail at the inputs
and outputs enables designers to buffer CMOS
DACs, ASICs, or other wide output swing devices in
single-supply systems.
3PEAK and the 3PEAK logo are registered trademarks of
3PEAK INCORPORATED. All other trademarks are the property
of their respective owners.
TP1561
5-Pin SOT23/SC70
-T and -C Suffixes
Out 1
Vs 2
+In 3
5 Vs
4 -In
TP1561
8-Pin MSOP/SOIC
-V and -S Suffixes
NC 1
In 2
In 3
Vs 4
8 NC
7 Vs
6 Out
5 NC
TP1561N
6-Pin SOT23
-T Suffix
TP1562
8-Pin SOIC/MSOP
-S and -V Suffixes
TP1564
14-Pin SOIC/TSSOP
-S and -T Suffixes
Out
Vs
+In
16
25
34
TP1561N
8-Pin MSOP/SOIC
-V and -S Suffixes
Vs
SHDN
-In
Out A
In A
In A
Vs
1
2
3
4
NC 1
In 2
In 3
Vs 4
8 SHDN
7 Vs
6 Out
5 NC
Out
Vs
+In
1
2
3
A
B
TP1561U
5-Pin SOT23
-T Suffix
8 Vs Out A
7 Out B In A
6 In B In A
5 In B Vs
In B
In B
Out B
5 Vs
4 -In
1
2
3
4
5
6
7
A
B
14 Out D
13 In D
D
12 In D
11 Vs
10 In C
C
9 In C
8 Out C
www.3peakic.com
REV1.2
1 



3Peak TP1561N
TP1561/TP1561N/TP1562/TP1564
        
Stable 3.8MHz, 130μA, RRIO, EveryCapTM Op Amps
Absolute Maximum Ratings Note 1
Supply Voltage: V+ – V....................................7.5V
Input Voltage............................. V– 0.5 to V+ + 0.5
Input Current: +IN, –IN, SHDN Note 2.............. ±10mA
SHDN Pin Voltage……………………………Vto V+
Output Current: OUT.................................... ±45mA
Output Short-Circuit Duration Note 3…......... Indefinite
Operating Temperature Range.......–40°C to 125°C
Maximum Junction Temperature................... 150°C
Storage Temperature Range.......... –65°C to 150°C
Lead Temperature (Soldering, 10 sec) ......... 260°C
Note 1: Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. Exposure to any
Absolute Maximum Rating condition for extended periods may affect device reliability and lifetime.
Note 2: The inputs are protected by ESD protection diodes to each power supply. If the input extends more than 500mV beyond the power
supply, the input current should be limited to less than 10mA.
Note 3: A heat sink may be required to keep the junction temperature below the absolute maximum. This depends on the power supply
voltage and how many amplifiers are shorted. Thermal resistance varies with the amount of PC board metal connected to the package. The
specified values are for short traces connected to the leads.
ESD, Electrostatic Discharge Protection
Symbol
HBM
MM
CDM
Parameter
Human Body Model ESD
Machine Model ESD
Charged Device Model ESD
Condition
MIL-STD-883H Method 3015.8
JEDEC-EIA/JESD22-A115
JEDEC-EIA/JESD22-C101E
Minimum Level
8
500
2
Unit
kV
V
kV
Order Information
Model Name
TP1561
TP1561U
TP1561N
TP1562
TP1564
Order Number
TP1561-TR
TP1561-CR
TP1561-VR
TP1561-SR
TP1561U-TR
TP1561N-TR
TP1561N-SR
TP1561N-VR
TP1562-SR
TP1562-VR
TP1564-SR
TP1564-TR
Package
5-Pin SOT23
5-Pin SC70
8-Pin MSOP
8-Pin SOIC
5-Pin SOT23
6-Pin SOT23
8-Pin SOIC
8-Pin MSOP
8-Pin SOIC
8-Pin MSOP
14-Pin SOIC
14-Pin TSSOP
Transport Media, Quantity
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 4000
Tape and Reel, 3000
Tape and Reel, 3000
Tape and Reel, 4000
Tape and Reel, 3000
Tape and Reel, 4000
Tape and Reel, 3000
Tape and Reel, 2500
Tape and Reel, 3000
Marking
Information
A6TYW (1)
A6CYW (1)
A61V
A61S
A6UYW (1)
A6NYW (1)
A61NS
A61NV
A62S
A62V
A64S
A64T
Note (1): ‘YW’ is date coding scheme. 'Y' stands for calendar year, and 'W' stands for single workweek coding scheme.
2  REV1.2
www.3peakic.com



3Peak TP1561N
TP1561/TP1561N/TP1562/TP1564
        
Stable 3.8MHz, 130μA, RRIO, EveryCapTM Op Amps
5V Electrical Characteristics
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at TA = 27°C.
VSUPPLY = 5V, VCM = VOUT = VSUPPLY/2, RL = 100K, CL =100pF, VSHDN is unconnected.
SYMBOL PARAMETER
CONDITIONS
MIN TYP MAX UNITS
VOS
VOS TC
IB
IOS
Vn
en
RIN
CIN
CMRR
VCM
PSRR
AVOL
VOL, VOH
ROUT
RO
ISC
VDD
IQ
IQ(off)
ISHDN
ILEAK
VIL
VIH
tON
tOFF
PM
GM
GBWP
tS
SR
FPBW
THD+N
Input Offset Voltage
VCM = VDD/2
-3.0 ±0.1 +3.0
mV
Input Offset Voltage Drift
0.6 μV/°C
Input Bias Current
1.0 pA
Input Offset Current
1.0 pA
Input Voltage Noise
Input Voltage Noise Density
f = 0.1Hz to 10Hz
f = 1kHz
f = 10kHz
2.4 μVP-P
27
14
nV/Hz
Input Resistance
> 100
G
Input Capacitance
Differential
Common Mode
2.0
3.5
pF
Common Mode Rejection Ratio
Common-mode Input Voltage
Range
VCM = 0.1V to 4.9V
80
120
V–0.3
V++0.3
dB
V
Power Supply Rejection Ratio
80
120
dB
Open-Loop Large Signal Gain
Output Swing from Supply Rail
Closed-Loop Output Impedance
Open-Loop Output Impedance
Output Short-Circuit Current
VOUT = 2.5V, RLOAD = 100k
VOUT = 0.1V to 4.9V, RLOAD = 100k
RLOAD = 100k
G = 1, f = 1kHz, IOUT = 0
f = 100kHz, IOUT = 0
Sink or source current
80
72
110
102
5
0.4
2.6
45
dB
dB
mV
mA
Supply Voltage
2.1 6.0 V
Quiescent Current per Amplifier
130 190
μA
Supply Current in Shutdown Note 1
0.2 μA
Shutdown Pin Current Note 1
Output Leakage Current in
Shutdown Note 1
SHDN Input Low Voltage Note 1
VSHDN = 0.5V
VSHDN = 1.5V
VSHDN = 0V, VOUT = 0V
VSHDN = 0V, VOUT = 5V
Disable
-0.15
-0.15
μA
-20
20
pA
0.5 V
SHDN Input High Voltage Note 1
Enable
1.0
V
Turn-On Time Note 1
SHDN Toggle from 0V to 5V
20 μs
Turn-Off Time Note 1
SHDN Toggle from 5V to 0V
20 μs
Phase Margin
Gain Margin
Gain-Bandwidth Product
RLOAD = 100k, CLOAD = 100pF
RLOAD = 100k, CLOAD = 100pF
f = 1kHz
66 °
-15 dB
3.8 MHz
Settling Time, 1.5V to 3.5V, Unity 0.1%
0.7
Gain
Settling Time, 2.45V to 2.55V,
0.01%
0.1%
0.8
0.1
μs
Unity Gain
0.01%
0.2
Slew Rate
Full Power Bandwidth Note 2
Total Harmonic Distortion and
Noise
AV = 1, VOUT = 1.5V to 3.5V, CLOAD =
100pF, RLOAD = 100k
2VP-P
f=1kHz, AV=1, RL=100k, VOUT = 2VPP
f=10kHz, AV=1, RL=100k, VOUT = 2VPP
3.6 V/μs
500 kHz
-115
-99
dB
Note 1: Specifications apply to the TP1561N with shutdown.
Note 2: Full power bandwidth is calculated from the slew rate FPBW = SR/π • VP-P.
www.3peakic.com
REV1.2
3 







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)