DatasheetsPDF.com

TSOP93636 Dataheets PDF



Part Number TSOP93636
Manufacturers Vishay
Logo Vishay
Description IR Receiver
Datasheet TSOP93636 DatasheetTSOP93636 Datasheet (PDF)

www.vishay.com TSOP936.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems ADDITIONAL RESOURCES 3D 3D 3D Models FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.0 V to 3.6 V • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 .

  TSOP93636   TSOP93636



Document
www.vishay.com TSOP936.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems ADDITIONAL RESOURCES 3D 3D 3D Models FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.0 V to 3.6 V • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 23051 MECHANICAL DATA 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The TSOP93... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP936.., series devices are designed to receive long burst codes (10 or more carrier cycles per burst). The third digit designates the AGC level (AGC6) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC6 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE AGC Carrier frequency Package Pinning Dimensions (mm) Mounting Application 30 kHz 33 kHz 36 kHz 38 kHz 40 kHz 56 kHz Best choice for MAXIMIZED NOISE SUPPRESSION (AGC6) TSOP93630 TSOP93633 TSOP93636 (5)(6) TSOP93638 (3)(4)(11) TSOP93640 TSOP93656 Minimold 1 = OUT, 2 = GND, 3 = VS 5.4 W x 6.35 H x 4.9 D Leaded Remote control (1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6 (8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony Notes • 30 kHz and 33 kHz only available on written request • See datasheet for TSOP932.., TSOP934.. for preferred devices for (1)(2)(7)(8)(9)(10)(12) Rev. 1.2, 31-Jul-2019 1 Document Number: 82842 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 www.vishay.com BLOCK DIAGRAM 16833-13 30 kΩ Input AGC Band pass Demodulator PIN Control circuit 3 1 2 TSOP936.. Vishay Semiconductors APPLICATION CIRCUIT 17170-12 Transmitter with TSALxxxx IR receiver Circuit VS OUT GND R1 C1 VO + VS μC GND R1 and C1 recommended to reduce supply ripple for VS < 2.2 V ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case VS IS VO IO Tj Tstg Tamb Ptot Tsd -0.3 to +3.6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 260 V mA V mA °C °C °C mW °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. Supply current Supply voltage Transmission distance Output voltage low Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 ISD ISH VS d VOSL 0.25 - 2.0 - - 0.37 0.50 32 - 0.45 3.6 - 100 Minimum irradiance Maximum irradiance Test signal: NEC code tpi - 5/f0 < tpo < tpi + 6/f0, test signal see Fig. 1 Ee min. Ee max. 30 0.07 0.15 -- Directivity Angle of half transmission distance ϕ1/2 - ± 45 - UNIT mA mA V m mV mW/m2 W/m2 ° Rev. 1.2, 31-Jul-2019 2 Document Number: 82842 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 www.vishay.com TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) TSOP936.. Vishay Semiconductors 1st line 2nd line Ee Optical Test Signal (IR diode TSAL6200, 30 pulses, f = f0, T = 15 ms) tpi (1) (1) tpi ≥ 10/f0 T Output Signal VO (2) 7/f0 < td < 15/f0 VOH (3) tpi - 5/f0 < tpo < tpi + 6/f0 VOL td (2) tpo (3) t 16110-11 t Fig. 1 - Output Delay and Pulse-Width 2nd line ton, toff - Output Pulse Width (ms) Axis Title.


TSOP93633 TSOP93636 TSOP93638


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)