DatasheetsPDF.com

RP506K151B Dataheets PDF



Part Number RP506K151B
Manufacturers RICOH
Logo RICOH
Description 2A PWM/VFM Step-down DC/DC Converter
Datasheet RP506K151B DatasheetRP506K151B Datasheet (PDF)

RP506x Series 2 A PWM/VFM Step-down DC/DC Converter with Synchronous Rectifier NO.EA-296-130925 OUTLINE The RP506x are low supply current CMOS-based PWM/VFM step-down DC/DC converters with synchronous rectifier featuring 2 A*1 output current. Internally, a single converter consists of an oscillator, a reference voltage unit, an error amplifier, a switching control circuit, a mode control circuit, a soft start circuit, a latch type protection circuit, an under-voltage lockout (UVLO) circuit, a th.

  RP506K151B   RP506K151B


Document
RP506x Series 2 A PWM/VFM Step-down DC/DC Converter with Synchronous Rectifier NO.EA-296-130925 OUTLINE The RP506x are low supply current CMOS-based PWM/VFM step-down DC/DC converters with synchronous rectifier featuring 2 A*1 output current. Internally, a single converter consists of an oscillator, a reference voltage unit, an error amplifier, a switching control circuit, a mode control circuit, a soft start circuit, a latch type protection circuit, an under-voltage lockout (UVLO) circuit, a thermal shutdown circuit, and switching transistors. The RP5 06x is empl oying synchronous rectification f or imp roving the efficiency of rectificatio n by repla cing diodes with built-in switching transistors. Using synchronous rectification not only increases circuit performance but also allows a design to reduce parts count. Power controlling method can be selected from forced PWM control type or PWM/VFM auto switching control type by inputting a signal to the MODE pin. In low output current, forced PWM control switches at fixed frequency rate in o rder to redu ce n oise. Likewi se, in low out put current, PWM/VFM auto swit ching co ntrol automati cally switches from PWM mode to VFM mode in order to achieve high efficiency. Output voltage type can be selected from an internally fixed output voltage type (RP506Kxx1A/B/D/E) or an externally adjustable output voltage type (RP506K001C/F). The output voltage of the RP506Kxx1A/B/D/E can be set by 0.1 V step and the output voltage accuracy is as high as ±1.5% or ±18 mV. The output voltage of the RP506K001C/F can be set by using the external resistors. Oscillator frequency can be selected from 2.25 MHz (RP506Kxx1A/B/C) or 1.2 MHz (RP506Kxx1D/E/F). Soft-start time is Typ. 0.15 ms, and by connecting an external capacitor to the TSS pin, soft-start time is adjustable. Power good (PG) function monitors the VOUT pin voltage or the feedback pin voltage (VFB), and switches the PG pin to low if any abnormal condition is detected. Protection circuits included in the RP506x are over current protection circuit, latch type protection circuit and thermal shutdown circuit. Over current protection circuit supervises the inductor peak current in each switching cycle, and if the current exceeds the LX current limit (ILXLIM), it turns off Pch Tr. Latch type protection circuit latches the built-in driver to the OFF state and stops the operation of the step-down DC/DC converter if the over current status continues or VOUT continues being the half of the setting volt age for equal or longer than protection delay time (tprot ). Therm al shut down ci rcuit detects ove rheating of the conve rter if the output pi n is shorte d to the ground pin (GND) etc. an d stops the c onverter operation to protect it from damage if the junctio n temperature exceeds the specified temperature. The RP506x is available in DFN(PLP)2527-10 which achieves high-density mounting on boards. *1 This is an approximate value. The output current is dependent on conditions and external components. 1 http://www.Datasheet4U.com RP506x NO.EA-296-130925 FEATURES z Supply Current················································ Typ. 48 µA (VFM mode, Lx at no load) z Standby Current·············································· Max. 5 µA z Input Voltage Range ······································· 2.5 V to 5.5 V (Absolute Maximum Ratings: 6.5 V) z Output Voltage Range*1 Version Forced PWM Control PWM/VFM Auto Switching Control RP506Kxx1A/B 1.1 V to 3.3 V 0.8 V to 3.3 V RP506K001C 1.1 V to 4.0 V 0.8 V to 4.0 V RP506Kxx1D/E 0.6 V to 3.3 V RP506K001F 0.6 V to 4.0 V z Output Voltage Accuracy ································ ±1.5% (VSET*2 ≥ 1.2 V), ································ ±18 mV (VSET < 1.2 V) (RP506Kxx1A/B/D/E) z Feedback Voltage Accuracy ··························· ±9 mV (VFB = 0.6 V) (RP506K001C/F) z Output Voltage/Feedback Voltage Temperature Coefficient·································· ±100 ppm/ºC z Oscillator Frequency······································· Typ. 2.25 MHz (RP506Kxx1A/B/C) ········································ Typ. 1.2 MHz (RP506Kxx1D/E/F) z Oscillator Maximum Duty································ Min. 100% z Built-in Driver ON Resistance························· Typ. Pch. 0.130 Ω, Nch. 0.125 Ω (VIN = 3.6 V) z UVLO Detector Threshold ······························ Typ. 2.2 V z Inductor Current Limit Circuit·························· Current limit Typ. 2.8 A z Latch Type Protection Circuit···················.


RP506K141B RP506K151B RP506K161B


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)