Document
MULTILAYER CERAMIC CHIP CAPACITORS
/ RCoomHplSian2t Temperature cycle : 1000 cycles
FEATURES
1. Large capacitance by small size. 2. Excellent noise absorption. 3. High permissible ripple current capability. 4. NTF: Temperature cycle : 1000 cycles.
APPLICATIONS
1. Smoothing circuit of DC-DC converters. 2. On-board power supplies. 3. Voltage regulators for computers. 3. Noise suppressor for various kinds of equipments. 4. High reliability equipments.
CONSTRUCTION
Ceramic Dielectric
Termination (Tin Plating)
RATINGS
1. Category Temperature Range 2. Rated Voltage Range 3. Rated Capacitance Range 4. Rated Capacitance Tolerance 5. Temperature Characteristics 6. Rated Ripple Current
Internal Electrode
-55 to +125 25, 50, 100, 250, 500Vdc 0.010 to 47 F M ( 20%) : Standard, K ( 10%) X7R See No.5 on the following table
SPECIFICATIONS
No. Items 1 Withstand Voltage
Specification No abnormality.
2 Insulation Resistance 3 Rated Capacitance
4 Dissipation Factor
100/CR(M ) or 4000(M ) whichever is less. Within specified tolerance.
5.0% maximum.
Test Condition
Rated voltage Less than 250V
More than 250V Less than 500V
Withstand voltage 250% of rated voltage 100V + 150% of rated voltage
More than 500V
130% of rated voltage
Shall be applied for 5 seconds.
Rated voltage shall be applied for 60 5 seconds at temperature 25 2 .
Temperature Frequency Voltage
CR 10 F
CR>10 F
25 2
1 0.1kHz
120 12Hz
1 0.2Vrms
0.5 0.2Vrms
5 Rated Ripple Current
See STANDARD RATINGS
10kHz 1MHz (sine curve) Ripple voltage Vp shall be less than the rated voltage.
As customer requirement, Chemi-Con has submits the test results according to AEC-Q200 for Multilayer ceramic capacitors. Please contact us for more information.
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
13 CAT. No. E1002W
MULTILAYER CERAMIC CHIP CAPACITORS
/
SPECIFICATIONS
No. Items 6 Adhesion
Specification No visible damage.
7 Bend strength of the face plating Appearance : No visible damage. C/C : 15%
Test Condition
Substrate 5N (0.51kgf) for 10 1 seconds Capacitor
The substrate shall be bend at a rate of 1mm/s for 5 seconds.
Capacitor
Press
Press bar Substrate
8 Solderability 9 Resistance to Soldering Heat 10 Temperature Cycle
11 Humidity Load Life 12 Endurance
Min. 75% of surface of the termination shall be covered with new solder
Appearance : No visible damage. C/C : 15%
D.F. : To meet the initial specification. I.R. : To meet the initial specification.
Appearance : No visible damage. C/C : 15%
D.F. : To meet the initial specification. I.R. : To meet the initial specification.
Appearance : No abnormality. C/C : 15%
D.F. : 10% maximum I.R. : 25/CR(M ) or 1000(M )
whichever is less.
Appearance : No abnormality. C/C : 15%
D.F. : 10% maximum I.R. : 50/CR(M ) or 1000(M )
whichever is less.
Bending capability*
45 2mm 45 2mm
*Bending capability NTS : 1mm NTF : 1mm or 2mm
Support
Solder Solder Temperature
Dipping Time
Pb Free 245 5 2 0.5sec.
Preheating Condition :
Step
Temperature
1 100 10
2 200 10
Solder Temperature : 260 5
Dipping Time
: 2 0.5 seconds
Time 2min. 2min.
Step 1 2 3 4
Temperature ( ) Min. Category temperature 3
Room temperature Max. Category temperature 3
Room temperature
For above temperature cycle. NTS : For 5 cycles NTF : For 1000 cycles
Temperature : 40 2
Humidity : 90 to 95%RH
Voltage
: Rated voltage
Time
: 500 204hours
(min.) 30 3 3 max.
30 3 3 max.
Temperature : 125 3
Voltage
: Rated voltage
Time
: 1000 408hours
*CR : Rated Capacitance( F)
Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications.
14 CAT. No. E1002W
MULTILAYER CERAMIC CHIP CAPACITORS
STANDARD RATINGS
Rated voltage Rated Capacitance
(Vdc)
( F)
L
Dimensions(mm) W Tmax.
Maximum ripple current a (Arms)
Part Number
1.0 KTS250B105M31N0T00
1.5
3.2 0.2
1.6 0.2
1.8 0.5 0.3
0.3 KTS250B155M31N0T00
2.2 KTS250B225M31N0T00
3.3 KTS250B335M32N0T00
25
4.7
3.2 0.4
2.5 0.3
2.6 0.6 0.3
6.8
0.5 KTS250B475M32N0T00 KTS250B685M32N0T00
10 15
4.5 0.4
3.2 0.4
2.8 0.6 0.3
1.0
KTS250B106M43N0T00 KTS250B156M43N0T00
22 33
5.7 0.4
5.0 0.4
2.8 3.0
0.8 0.5
2.0
KTS250B226M55N0T00 KTS250B336M55N0T00
47
7.5 0.5
6.3 0.5
4.0 1.0 0.5
3.0 KTS250B476M76N0T00
0.33 KTS500B334M31N0T00
0.47 0.68
3.2 0.2
1.6 0.2
1.8 0.5 0.3
0.3
KTS500B474M31N0T00 KTS500B684M31N0T00
1.0 KTS500B105M31N0T00
1.5 KTS500B155M32N0T00
50
2.2
3.2 0.4
2.5 0.3
2.6 0.6 0.3
0.5 KTS500B225M32N0T00
3.3 KTS500B335M32N0T00
4.7 6.8
4.5 0.4
3.2 0.4
2.8 0.6 0.3
1.0
KTS500B475M43N0T00 KTS500B685M43N0T00
10 15
5.7 0.4
5.0 0.4
2.8 0.8 0.5
2.0
KTS500B106M55N0T00 KTS500B156M55N0T00
2.