IS32LT3175P Datasheet: SINGLE CHANNEL LINEAR LED DRIVER





IS32LT3175P SINGLE CHANNEL LINEAR LED DRIVER Datasheet

Part Number IS32LT3175P
Description SINGLE CHANNEL LINEAR LED DRIVER
Manufacture ISSI
Total Page 19 Pages
PDF Download Download IS32LT3175P Datasheet PDF

Features: IS32LT3175N/P SINGLE CHANNEL LINEAR LED DRIVER WITH FADE IN/OUT AND PWM DIMMING GENERAL DESCRIPTION The IS32LT3175 is a single channel linear programmable c urrent regulator capable of up to 150mA . It integrates a debounce and latch ci rcuit on the channel enable pin (EN) to facilitate the use of a low cost momen tary contact switch. The PWM pin can be interfaced to a logic level “courtes y light” signal to directly drive the LED channel. The IS32LT3175P accepts a positive polarity PWM signal while the IS32LT3175N accepts a negative polarit y PWM signal. The device operates as a stand-alone LED driver configurable wit h external resistors; no microcontrolle r is required. A single external resist or programs the current level, while tw o separate resistors independently prog ram the fade in and fade out ramp rate for the channel. The device integrates a 63 steps fade in and fade out algorit hm (Gamma correction) which causes the output LED current to gradually ramp up to the full source value af.

Keywords: IS32LT3175P, datasheet, pdf, ISSI, SINGLE, CHANNEL, LINEAR, LED, DRIVER, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute, Equivalent

IS32LT3175N/P
SINGLE CHANNEL LINEAR LED DRIVER WITH FADE IN/OUT AND PWM DIMMING
GENERAL DESCRIPTION
The IS32LT3175 is a single channel linear
programmable current regulator capable of up to
150mA. It integrates a debounce and latch circuit on
the channel enable pin (EN) to facilitate the use of a
low cost momentary contact switch. The PWM pin can
be interfaced to a logic level “courtesy light” signal to
directly drive the LED channel. The IS32LT3175P
accepts a positive polarity PWM signal while the
IS32LT3175N accepts a negative polarity PWM signal.
The device operates as a stand-alone LED driver
configurable with external resistors; no microcontroller
is required. A single external resistor programs the
current level, while two separate resistors
independently program the fade in and fade out ramp
rate for the channel.
The device integrates a 63 steps fade in and fade out
algorithm (Gamma correction) which causes the output
LED current to gradually ramp up to the full source
value after the EN pin is pulsed. The same controller
causes the LED current to gradually ramp down to
zero if the EN pin is pulsed while the output channel is
ON. The fade ramp can be interrupted mid-cycle
before completion of the ramp cycle. The EN pin will
accept either a momentary contact switch or logic level
signal pulsed low.
The IS32LT3175 is targeted at the automotive market
with end applications to include map and dome lighting
as well as exterior accent lighting. For 12V automotive
applications the low dropout driver can support 1 to 3
LEDs (VF = 3.2V) per channel. It is offered in a small
thermally enhanced SOP-8-EP package.
TYPICAL APPLICATION CIRCUIT
July 2016
FEATURES
Operating voltage 5V to 42V
Single channel current source
- Programmable current via a single external
resistor
- Configurable from 20mA to 150mA
Momentary contact button EN input
- Input is debounced and latched
- Higher priority than PWM input
- Gamma corrected Fade In/Out algorithm
- Pull down resistors set independent fade IN and
OUT ramp time
PWM input pin driven by external PWM source
- PWM directly drives the current source
- IS32LT3175P – Positive polarity
- IS32LT3175N – Negative polarity
Fault Protection:
- OUT pin shorted to GND
- ISET pin shorted to GND
- Over temperature
SOP-8-EP package
Automotive Grade:
- IS32LT3175P – AEC-Q100
- IS32LT3175N – AEC-Q100
Operating temperature range from -40°C ~ +125°C
APPLICATIONS
Automotive Interior:
- Map/Dome light
- Puddle lamp in doors
- Glove box
- Vanity mirror
Figure 1 Typical Application Circuit
Note: The resistor RPWM is a fixed value. Please don’t change it. CPWM is optional. Add it for robust electromagnetic susceptibility.
Integrated Silicon Solution, Inc. – www.issi.com
Rev.A, 07/19/2016
1

                    
                    






Index : 0  1  2  3   4  5  6  7   8  9  A  B   C  D  E  F   G  H  I  J   K  L  M  N   O  P  Q  R   S  T  U  V   W  X  Y  Z
@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)