PRE-FET DRIVER. TPIC44H01 Datasheet

TPIC44H01 DRIVER. Datasheet pdf. Equivalent

Part TPIC44H01
Description 4-CHANNEL SERIAL AND PARALLEL HIGH-SIDE PRE-FET DRIVER
Feature TPIC44H01 4-CHANNEL SERIAL AND PARALLEL HIGH-SIDE PRE-FET DRIVER D Serial or Parallel Control of Ga.
Manufacture etcTI
Total Page 30 Pages
Datasheet
Download TPIC44H01 Datasheet



TPIC44H01
TPIC44H01
4-CHANNEL SERIAL AND PARALLEL HIGH-SIDE PRE-FET DRIVER
D Serial or Parallel Control of Gate Outputs
D Sleep State for Low Quiescent Current
D Independent On-State Source
Short-to-Ground (Shorted-Load)
Detection/Protection
D Independent On-State Over-Current
Detection/Protection With Dynamic Fault
Threshold
D Independent Off-State Open-Load
Detection
D Supply Over-Voltage Lockout Protection
D Asynchronous Open-Drain Fault Interrupt
Terminal to Flag Fault Conditions. Output
Can be OR’ed With Multiple Devices
D Encoded Fault Status Reporting Through
Serial Output Terminal (2-Bits Per Channel)
D Programmable On-State Fault Deglitch
Timers
D High Impedance CMOS Compatible Inputs
With Hysteresis
D Fault Mode Selection: Outputs Latched Off
or Switched at Low Duty Cycle
D Device Can be Cascaded With Serial
Interface
CS
SD0
SDI
SCLK
AR_ENBL
GND
IN1
IN2
IN3
IN4
VCC
V(PK_A)
V(PK_B)
V(COMP1)
V(COMP2)
V(COMP3)
SLIS088 – SEPTEMBER 1998
DA PACKAGE
(TOP VIEW)
1 32 PGND
2 31 V(PWR)
3 30 CP1
4 29 CP2
5 28 V(CP)
6 27 GATE1
7 26 SRC1
8 25 GATE2
9 24 SRC2
10 23 GATE3
11 22 SRC3
12 21 GATE4
13 20 SRC4
14 19 FLT
15 18 RESET
16 17 V(COMP4)
description
The TPIC44H01 is a four channel high-side pre-FET driver which provides serial or parallel input interface to
control four external NMOS power FETs. It is designed for use in low frequency switching applications for
resistive or inductive loads, including solenoids and incandescent bulbs.
Each channel has over-current, short-to-ground, and open-load detection that is flagged through the FLT pin
and distinguished through the serial interface. Over-current thresholds are set through the V(PK_x) and
V(COMP1-4) pins. Short-to-ground and open-load thresholds are set internally to approximately 2.5 V. The
AR_ENBL pin is used to define the operation of the device during a fault condition, allowing the outputs to either
latch off or to enter a low duty cycle, auto-retry mode. An over-voltage lockout circuit on V(PWR) protects the
device and the external FETs. A low current sleep state mode is provided to allow the TPIC44H01 to be used
in applications where V(PWR) is connected directly to the battery. An internal charge pump allows the use of
N-channel FETs for high-side drive applications, while current-limit gate drive provides slope control for reduced
RFI.
By having the unique ability to develop a dynamic over-current threshold, the TPIC44H01 can be used to drive
incandescent bulbs with long inrush currents without falsely flagging a fault. Likewise, the user can select an
internally set over-current threshold of ~1.25 V by pulling the respective V(COMP1-4) pin to VCC.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
TI is a trademark of Texas Instruments Incorporated.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 1998, Texas Instruments Incorporated
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1



TPIC44H01
TPIC44H01
4-CHANNEL SERIAL AND PARALLEL HIGH-SIDE PRE-FET DRIVER
SLIS088 – SEPTEMBER 1998
description (continued)
The 8-bit serial peripheral interface (SPI) allows the user to command any of the four outputs on or off, to
program one of eight possible open-load, over-current, and short-load fault deglitch timer settings, and to
engage the sleep state. Data is clocked into the SDI pin on the rising edge of SCLK and clocked out of the SDO
pin on the SCLK falling edge. The serial input bits are logic OR’ed with the IN1-IN4 parallel inputs pins. The serial
interface is also used to read normal-load, open-load, over-current, and short-to-ground conditions for each
channel. Over-voltage lockout can be detected when the FLT pin is low and no bits are set in the SDO register.
Multiple TPIC44H01 devices may be cascaded together using the serial interface to further reduce I/O lines from
the host controller.
2 POST OFFICE BOX 655303 DALLAS, TEXAS 75265





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)