IGBT Module. 6MBP30VSC060-50 Datasheet

6MBP30VSC060-50 Module. Datasheet pdf. Equivalent

Part 6MBP30VSC060-50
Description IGBT Module
Feature http://www.fujielectric.com/products/semiconductor/ 6MBP30VSC060-50 IGBT Modules IGBT MODULE (V s.
Manufacture Fuji Electric
Total Page 12 Pages
Datasheet
Download 6MBP30VSC060-50 Datasheet



6MBP30VSC060-50
http://www.fujielectric.com/products/semiconductor/
6MBP30VSC060-50
IGBT Modules
IGBT MODULE (V series)
600V / 30A / IPM
Features
Low-side IGBTs are separate emitter type
Short circuit protection
Temperature sensor output function
Under voltage protection
Fault signal output function
Input interface : TTL (3.3V/5V) Active high logic
Applications
AC 100 ~ 240V three phase inverter drive for small power
AC motor drives (such as compressor motor drive for
air conditioner, compressor motor drive for heat pump
applications, fan motor drive, ventilator motor drive)
Terminal assign and Internal circuit
3 VB(U)
5 VB(V)
7 VB(W)
9 IN(HU)
10 IN(HV)
11 IN(HW)
12 VCCH
13 COM
14 IN(LU)
15 IN(LV)
16 IN(LW)
17 VCCL
18 VFO
19 IS
20 COM
21 TEMP
IN VB
Vcc OUT
GND Vs
IN VB
Vcc OUT
GND Vs
IN VB
Vcc OUT
GND Vs
UIN UOUT
VIN
WIN
Vcc
VOUT
Fo
IS
WOUT
GND
TEMP
NC 36
P 32
U 30
V 28
W 26
N(U) 24
N(V) 23
N(W) 22
Pin No. Pin Name Pin Description
3 VB (U) High-side bias voltage for U-phase IGBT driving
5 VB (V) High-side bias voltage for V-phase IGBT driving
7 VB (W) High-side bias voltage for W-phase IGBT driving
9 IN (HU) Signal input for high side U-phase
10 IN (HV) Signal input for high side V-phase
11 IN (HW) Signal input for high side W-phase
12 VCCH
High-side control supply
13 COM Common supply ground
14 IN (LU) Signal input for low side U-phase
15 IN (LV) Signal input for low side V-phase
16 IN (LW) Signal input for low side W-phase
17 VCCL
Low-side control supply
18 VFO Fault output
19 IS
Over current sensing voltage input
20 COM Common supply ground
21
TEMP
Temperature sensor output
22
N (W)
Negative bus voltage input for W-phase
23 N (V) Negative bus voltage input for V-phase
24
N (U)
Negative bus voltage input for U-phase
26 W
Motor W-phase output
28 V
Motor V-phase output
30 U
Motor U-phase output
32 P
Positive bus voltage input
36 NC
No Connection
1 1536a
JUNE 2014



6MBP30VSC060-50
6MBP30VSC060-50
IGBT Modules
http://www.fujielectric.com/products/semiconductor/
Absolute Maximum Ratings at Tj=25°C, VCC=15V (unless otherwise specified)
Items
DC Bus Voltage
Bus Voltage (Surge)
Collector-Emitter Voltage
Collector Current
Symbol
VDC
VDC(Surge)
VCES
IC@25
Characteristics
450
500
600
30
Unit
V
V
V
A
Remarks
Note *1
Note *1
Note *2
Peak Collector Current
ICP@25
90
A
VCC15V, VB(*)15V
Note *2, *3, *4
60
A
VCC13V, VB(*)13V
Note *2, *3, *4
Diode Forward current
Peak Diode Forward current
Collector Power Dissipation
FWD Power Dissipation
Junction Temperature
IF@25
IFP@25
PD_IGBT
PD_FWD
Tj
30
90
80.1
39.5
150
A Note *2
A Note *2
W per single IGBT TC=25°C
W per single FWD TC=25°C
°C
Operating Junction Temperature
(Under switching conditions)
TjOP
-40 ~ +125
°C
High-side Supply Voltage
Low-side Supply Voltage
VCCH
-0.5 ~ 20
V Applied between VCCH-COM
VCCL
-0.5 ~ 20
V Applied between VCCL-COM
High-side Bias Absolute Voltage
VVB(U)-COM
VVB(V)-COM
VVB(W)-COM
-0.5 ~ 620
Applied between
V VB(U)-COM, VB(V)-COM,
VB(W)-COM
High-side Bias Voltage for
IGBT gate driving
VB(U)
VB(V)
VB(W)
-0.5 ~ 20
V Note *4
High-side Bias offset Voltage
Input Signal Voltage
Input Signal Current
Fault Signal Voltage
Fault Signal Current
Over Current sensing Input Voltage
Junction Temperature
VU
VV
VW
VIN
IIN
VFO
IFO
VIS
Tj
-5 ~ 600
-0.5 ~ VCCH+0.5
-0.5 ~ VCCL+0.5
3
-0.5 ~ VCCL+0.5
1
-0.5 ~ VCCL+0.5
150
Applied between
V U-COM, V-COM, W-COM
Note *5
V Note *6
mA sink current
V Applied between VFO-COM
mA sink current
V Applied between IS-COM
°C
Operating Junction Temperature
(Under switching conditions)
TjOP
-40 ~ +125
°C
Operating Case Temperature
Storage Temperature
Isolation Voltage
TC
-40 ~ +125
°C See Fig.1-1
Tstg
-40 ~ +125
°C
Viso
AC 1500
Vrms Sine wave, 60Hz t=1min, Note *7
Note *1 : Applied between P-N(U), P-N(V), P-N(W)
Note *2 : Pulse width and duty were limited by T jmax.
Note *3 : VCC is applied between VCCH-COM,VCCL-COM.
Note *4 : VB(*) is applied between VB(U)-U, VB(V)-V, VB(W)-W.
Note *5 : ‌O ver 13.0V applied between VB(U)-U, VB(V)-V, VB(W)-W. This IPM module might make incorrect response if the high-side bias offset voltage is less than
-5V.
Note *6 : Applied between IN(HU)-COM, IN(HV)-COM, IN(HW)-COM, IN(LU)-COM, IN(LV)-COM, IN(LW)-COM.
Note *7 : Applied between shorted all terminal and IMS (Insulated Metal Substrate).
2





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)