DatasheetsPDF.com

TGHDX27R0JE Dataheets PDF



Part Number TGHDX27R0JE
Manufacturers OHMITE
Logo OHMITE
Description Chassis Mounting Non-inductive High Power Resistors
Datasheet TGHDX27R0JE DatasheetTGHDX27R0JE Datasheet (PDF)

TGHD Series Chassis Mounting Non-inductive High Power Resistors F e at u r e s • #187 Quick connect tabs or fly wire leads • Flat type, 100W high power resistor • Air-cooled heat sink or water-cooling required. • Higher density packing, vibration-proof, insulation withstand voltage and perfect heat dissipation possible. • TGHDX with wire leads follows the popular SOT-227 land pattern. A p p l i c at i o n s • Harmonic filter • Gate resistor • Snubber resistors • Dumping resistor for • Surge .

  TGHDX27R0JE   TGHDX27R0JE



Document
TGHD Series Chassis Mounting Non-inductive High Power Resistors F e at u r e s • #187 Quick connect tabs or fly wire leads • Flat type, 100W high power resistor • Air-cooled heat sink or water-cooling required. • Higher density packing, vibration-proof, insulation withstand voltage and perfect heat dissipation possible. • TGHDX with wire leads follows the popular SOT-227 land pattern. A p p l i c at i o n s • Harmonic filter • Gate resistor • Snubber resistors • Dumping resistor for • Surge protection automotive electronics • Breeder resistor • Power supplies • Dummy load • High frequency amplifiers c h a r a c t e r i st i c s Rated Power Heat Resistance Resistance Range Nominal Resistance TCR Tolerance Operation Temp. Max. Applied Voltage Withstanding Voltage Torque Weight Insulation Resistance 100W at flange temperature -55 to +100°C (wire leads) or -55 to +25°C (quick connect) 0.5°C/W (wire leads) or 1.1°C/W (quick connect) from resistor to flange 0.1Ω to 51kΩ; lowest 0.1 ohm is available E24+ Modified E24, additionally, 2.0 and 5.0 ±100 ppm/K (A) For -55 to +155°C ±5% (J) -55 to +155°C at flange element surface E = √P·R or 1000V 5000 VAC 60 seconds, leak current below 0.5mA Mounting 1.6Nm max, 1.0Nm recommend 14g Over 1000MΩ between terminals and flange Test Load Life Humidity Temperature Cycle Vibration Flammability Procedure Continuous power 1000 hours 60°C, 90 to 95%RH, DC0.1W, 1000 hours -55°C, 30 min.,+155°C 30min., 5 cycles IEC60068-2-6, displacement 0.75mm or acceleration 100m/sec^2, 10Hz-54Hz sweep, 10 cycles X-Y-Z direction For resistor body Requirement ΔR±1.0% ΔR±1.0% ΔR±1.0% ΔR±0.5% UL94V-0 Derating % Rated Power 100 -55° 80 25° 100° 60 Wire 40 leads 20 Quick connect 0 -60 -30 0 30 60 90 120 155° Flange Temperature (°C) Construction Flange Ni plated copper Molding Epoxy resin Case PA6 resin Resistor Thick film Substrate Alumina ceramics Wire Terminals Insulation wire UL Tab terminals #187tab terminals 156 1-866-9-OHMITE • Int’l 1-847-258-0300 • Fax 1-847-574-7522 • www.ohmite.com • [email protected] (continued) TGHD Series Chassis Mounting Non-inductive High Power Resistors dimensions 19.0 ±1.0 14.0 ±.2 5.5 ±.5 Wire Terminals 1.5 ±.2 (310) Tab Terminals (19.0) 32.0 ±.2 31±.2 19.0 ±.5 32.0 ±.2 26.0 ±.2 24±.2 3.8+/-0.2 0.75SQ RSU AWG #10 2-R1.90 10.5 ±.2 (17.0) 10.0 ±1 OR D ERIN G IN F ORMA T ION RoHS Compliant TGHDV10R0JE Series Termination V = Quick Connect X = Wired Ohm Value Tolerance J = 5% std. Standard part numbers Quick Connect Wired Termination TGHDVR100JE TGHDVR500JE TGHDV1R00JE TGHDV5R00JE TGHDV10R0JE TGHDV27R0JE TGHDV47R0JE TGHDV100RJE TGHDV270RJE TGHDV470RJE TGHDV1K00JE TGHDV5K00JE TGHDXR100JE TGHDXR500JE TGHDX1R00JE TGHDX5R00JE TGHDX10R0JE TGHDX27R0JE TGHDX47R0JE TGHDX100RJE TGHDX270RJE TGHDX470RJE TGHDX1K00JE TGHDX5K00JE Available values Resistance value is available following modified E24, +E24. Contact factory for other values. 1.0 1.8 3.0 4.7 7.5 1.1 2.0 3.3 5.0.


TGHDX10R0JE TGHDX27R0JE TGHDX47R0JE


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)