(PDF) TLC5904 Datasheet PDF | etcTI





TLC5904 Datasheet PDF

Part Number TLC5904
Description LED DRIVER
Manufacture etcTI
Total Page 28 Pages
PDF Download Download TLC5904 Datasheet PDF

Features: Datasheet pdf TLC5904 LED DRIVER D Drive Capability a nd Output Counts – 80 mA (Current Sin k) x 16 Bits – 120 mA (Current Sink) x 8 Bits D Constant Current Output Rang e – 5 to 80 mA/10 to 120mA (Selectabl e by MODE Terminal) (Current Value Sett ing for All Output Terminals Using Exte rnal Resistor and Internal Brightness C ontrol Register) D Constant Current Acc uracy – ± 4% (Maximum Error Between Bits) D Voltage Applied to Constant Cur rent Output Terminals – Minimum 0.4 V (Output Current 5 mA to 40 mA) – Min imum 0.7 V (Output Current 40 to 80 mA) D 256 Gray Scale Display – Pulse Wid th Control 256 Steps D Brightness Adjus tment – Output Current Adjustment for 32 Steps (Adjustment for Brightness De viation Between LED Modules) – 8 Step s Brightness Control by 8 Times Speed G ray Scale Control Clock (Brightness Adj ustment for Panel) D Error Output Signa l Check – Check Error Output Signal L ine Such as Protection Circuit When Ope rating SLLS391 – NOVEMBER 1999 D Data Output Timing Selectable – Select Data Output.

Keywords: TLC5904, datasheet, pdf, etcTI, LED, DRIVER, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute, Equivalent

TLC5904 datasheet
TLC5904
LED DRIVER
D Drive Capability and Output Counts
– 80 mA (Current Sink) x 16 Bits
– 120 mA (Current Sink) x 8 Bits
D Constant Current Output Range
– 5 to 80 mA/10 to 120mA (Selectable by
MODE Terminal) (Current Value Setting for
All Output Terminals Using External
Resistor and Internal Brightness Control
Register)
D Constant Current Accuracy
± 4% (Maximum Error Between Bits)
D Voltage Applied to Constant Current Output
Terminals
– Minimum 0.4 V (Output Current 5 mA to
40 mA)
– Minimum 0.7 V (Output Current 40 to
80 mA)
D 256 Gray Scale Display
– Pulse Width Control 256 Steps
D Brightness Adjustment
– Output Current Adjustment for 32 Steps
(Adjustment for Brightness Deviation
Between LED Modules)
– 8 Steps Brightness Control by 8 Times
Speed Gray Scale Control Clock
(Brightness Adjustment for Panel)
D Error Output Signal Check
– Check Error Output Signal Line Such as
Protection Circuit When Operating
SLLS391 – NOVEMBER 1999
D Data Output Timing Selectable
– Select Data Output Timing for Shift
Register Relative to Clock
D OVM (Output Voltage Monitor)
– Monitor Voltage on Constant Current
Output Terminals (Detect LED
Disconnection and Short Circuit)
D WDT (Watchdog Timer)
– Turn Output Off When Scan Signal
Stopped
D TSD (Thermal ShutDown)
– Turn Output Off When Junction
Temperature Exceeds Limit
D Data Input
– Clock Synchronized 8 Bit Parallel Input
(Schmitt-Triggered Input)
D Data Output
– Clock Synchronized 8 Bit Parallel Output
(3-State Output)
D Input Signal Level . . . CMOS Level
D Power Supply Voltage . . . 4.5 V to 5.5 V
D Maximum Output Voltage . . . 17 V (Max)
D Data Transfer Rate . . . 15 MHz (Max)
D Gray Scale Clock Frequency
8 MHz (Max)
D Operating Free-Air Temperature Range
–20_C to 85_C
D 100-Pin HTQFP Package (PD=4.7 W,
TA = 25°C)
description
The TLC5904 is a constant current driver incorporating shift register, data latch, and constant current circuitry
with current value adjustable and a 256 gray scale display using pulse width control. The output current can be
selected as maximum 80 mA with 16 bits or 120 mA with 8 bits, and the current value of constant current output
can be set by one external resistor. After this device is mounted on a PCB, the brightness deviation between
LED modules (ICs) can be adjusted by external data input, and the brightness control for the panel can be
accomplished by the brightness adjustment circuitry. Also, the device incorporates the output voltage monitor
(OVM) used for LED open detection (LOD) by monitoring the constant current output. Moreover, the device
incorporates watchdog time (WDT) circuitry, which turns the constant current output off when a scan signal is
stopped at the dynamic scanning operation, and thermal shutdown (TSD) circuitry, which turns the constant
current output off when the junction temperature exceeds the limit.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
POST OFFICE BOX 655303 DALLAS, TEXAS 75265
Copyright © 1998, Texas Instruments Incorporated
1

TLC5904 datasheet
TLC5904
LED DRIVER
SLLS391 – NOVEMBER 1999
NC
NC
OUT4
NC
GNDLED
NC
OUT5
OUT6
NC
GNDLED
NC
OUT7
OUT8
NC
GNDLED
NC
OUT9
OUT10
NC
GNDLED
NC
OUT11
NC
NC
NC
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
PZP PACKAGE
(TOP VIEW)
75 TEST2
74 DOMODE
73 DIN3
72 DIN2
71 DIN1
70 DIN0
69 GSCLK
68 BLANK
67 RSEL1
66 RSEL0
65 DCLK
64 XENABLE
63 XOE
62 WDTRG
61 XLATCH
60 XDOWN1
59 XDOWN2
58 TEST1
57 BOUT
56 GSOUT
55 DOUT0
54 DOUT1
53 DOUT2
52 DOUT3
51 DOUT4
2 POST OFFICE BOX 655303 DALLAS, TEXAS 75265




Index : 0  1  2  3   4  5  6  7   8  9  A  B   C  D  E  F   G  H  I  J   K  L  M  N   O  P  Q  R   S  T  U  V   W  X  Y  Z
@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)