C8051F583 MCU Datasheet

C8051F583 Datasheet PDF, Equivalent


Part Number

C8051F583

Description

Mixed Signal ISP Flash MCU

Manufacture

Silicon Laboratories

Total Page 30 Pages
PDF Download
Download C8051F583 Datasheet PDF


C8051F583
Analog Peripherals
- 12-Bit ADC
Up to 200 ksps
Up to 32 external single-ended inputs
VREF from on-chip VREF, external pin or VDD
Internal or external start of conversion source
Built-in temperature sensor
- Three Comparators
Programmable hysteresis and response time
Configurable as interrupt or reset source
Low current
On-Chip Debug
- On-chip debug circuitry facilitates full speed, non-
intrusive in-system debug (no emulator required)
- Provides breakpoints, single stepping,
inspect/modify memory and registers
- Superior performance to emulation systems using
ICE-chips, target pods, and sockets
- Low cost, complete development kit
Supply Voltage 1.8 to 5.25 V
- Typical operating current: 15 mA at 50 MHz;
Typical stop mode current: 230 µA
High-Speed 8051 µC Core
- Pipelined instruction architecture; executes 70% of
instructions in 1 or 2 system clocks
- Up to 50 MIPS throughput with 50 MHz clock
- Expanded interrupt handler
Automotive Qualified
- Temperature Range: –40 to +125 °C
C8051F58x/F59x
Mixed Signal ISP Flash MCU Family
Memory
- 8448 bytes internal data RAM (256 + 8192 XRAM)
- 128 or 96 kB Banked Flash; In-system programma-
ble in 512-byte Sectors
- External 64 kB data memory interface programma-
ble for multiplexed or non-multiplexed mode
Digital Peripherals
- 40, 33, or 25 Port I/O; All 5 V push-pull with high
sink current
- CAN 2.0 Controller—no crystal required
- LIN 2.1 Controller (Master and Slave capable); no
crystal required
- Two Hardware enhanced UARTs, SMBus™, and
enhanced SPI™ serial ports
- Six general purpose 16-bit counter/timers
- Two 16-Bit programmable counter array (PCA)
peripherals with six capture/compare modules each
and enhanced PWM functionality
Clock Sources
- Internal 24 MHz with ±0.5% accuracy for CAN and
master LIN operation.
- External oscillator: Crystal, RC, C, or clock
(1 or 2 pin modes)
- Can switch between clock sources on-the-fly;
useful in power saving modes
Packages
- 48-Pin QFP/QFN (C8051F580/1/4/5)
- 40-Pin QFN (C8051F588/9-F590/1)
- 32-Pin QFP/QFN (C8051F582/3/6/7)
ANALOG
PERIPHERALS
A 12-bit
M
U
200 ksps
TEMP
SENSOR
X ADC
Voltage VREG
Comparators 0-2 VREF
DIGITAL I/O
UART 0-1
SMBus
SPI
PCA x 2
Timers 0-5
CAN
LIN
Ports 0-4
Crossbar
External
Memory
Interface
24 MHz PRECISION
INTERNAL OSCILLATOR
2x Clock Multiplier
HIGH-SPEED CONTROLLER CORE
128 kB
ISP FLASH
FLEXIBLE
INTERRUPTS
8051 CPU
(50 MIPS)
DEBUG
CIRCUITRY
8 kB XRAM
POR WDT
Rev 1.5 5/18
Copyright © 2018 by Silicon Laboratories C8051F580/1/2/3/4/5/6/7/8/9-F590/1

C8051F583
C8051F58x/F59x
Table of Contents
1. System Overview ..................................................................................................... 18
2. Ordering Information ............................................................................................... 22
3. Pin Definitions.......................................................................................................... 24
4. Package Specifications ........................................................................................... 32
4.1. QFP-48 Package Specifications........................................................................ 32
4.2. QFN-48 Package Specifications........................................................................ 34
4.3. QFN-40 Package Specifications........................................................................ 36
4.4. QFP-32 Package Specifications........................................................................ 38
4.5. QFN-32 Package Specifications........................................................................ 40
5. Electrical Characteristics ........................................................................................ 42
5.1. Absolute Maximum Specifications..................................................................... 42
5.2. Electrical Characteristics ................................................................................... 43
6. 12-Bit ADC (ADC0) ................................................................................................... 54
6.1. Modes of Operation ........................................................................................... 55
6.1.1. Starting a Conversion................................................................................ 55
6.1.2. Tracking Modes......................................................................................... 55
6.1.3. Timing ....................................................................................................... 56
6.1.4. Burst Mode................................................................................................ 57
6.2. Output Code Formatting .................................................................................... 59
6.2.1. Settling Time Requirements...................................................................... 59
6.3. Selectable Gain ................................................................................................. 60
6.3.1. Calculating the Gain Value........................................................................ 60
6.3.2. Setting the Gain Value .............................................................................. 62
6.4. Programmable Window Detector....................................................................... 68
6.4.1. Window Detector In Single-Ended Mode .................................................. 70
6.5. ADC0 Analog Multiplexer .................................................................................. 72
7. Temperature Sensor ................................................................................................ 74
8. Voltage Reference.................................................................................................... 75
9. Comparators............................................................................................................. 77
9.1. Comparator Multiplexer ..................................................................................... 85
10. Voltage Regulator (REG0) ..................................................................................... 89
11. CIP-51 Microcontroller........................................................................................... 91
11.1. Performance .................................................................................................... 91
11.2. Instruction Set.................................................................................................. 93
11.2.1. Instruction and CPU Timing .................................................................... 93
11.3. CIP-51 Register Descriptions .......................................................................... 97
11.4. Serial Number Special Function Registers (SFRs) ....................................... 101
12. Memory Organization .......................................................................................... 102
12.1. Program Memory........................................................................................... 102
12.1.1. MOVX Instruction and Program Memory .............................................. 104
12.2. Data Memory ................................................................................................. 104
12.2.1. Internal RAM ......................................................................................... 105
12.2.1.1. General Purpose Registers .......................................................... 105
Rev 1.5
3


Features Analog Peripherals - 12-Bit ADC • Up t o 200 ksps • Up to 32 external single -ended inputs • VREF from on-chip VRE F, external pin or VDD • Internal or external start of conversion source • Built-in temperature sensor - Three Co mparators • Programmable hysteresis a nd response time • Configurable as in terrupt or reset source • Low current On-Chip Debug - On-chip debug circuitr y facilitates full speed, non- intrusiv e in-system debug (no emulator required ) - Provides breakpoints, single steppi ng,  inspect/modify memory and regis ters - Superior performance to emulatio n systems using ICE-chips, target pods, and sockets - Low cost, complete devel opment kit Supply Voltage 1.8 to 5.25 V - Typical operating current: 15 mA at 50 MHz; Typical stop mode current: 2 30 µA High-Speed 8051 µC Core - Pipel ined instruction architecture; executes 70% of instructions in 1 or 2 system c locks - Up to 50 MIPS throughput with 5 0 MHz clock - Expanded interrupt handler Automotive Qualified - Temperature Range: –4.
Keywords C8051F583, datasheet, pdf, Silicon Laboratories, Mixed, Signal, ISP, Flash, MCU, 8051F583, 051F583, 51F583, C8051F58, C8051F5, C8051F, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)