DatasheetsPDF.com

TSOP93540 Dataheets PDF



Part Number TSOP93540
Manufacturers Vishay
Logo Vishay
Description IR Receiver Modules
Datasheet TSOP93540 DatasheetTSOP93540 Datasheet (PDF)

www.vishay.com TSOP931.., TSOP933.., TSOP935.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems ADDITIONAL RESOURCES 3D 3D 3D Models FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.0 V to 3.6 V • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.

  TSOP93540   TSOP93540



Document
www.vishay.com TSOP931.., TSOP933.., TSOP935.. Vishay Semiconductors IR Receiver Modules for Remote Control Systems ADDITIONAL RESOURCES 3D 3D 3D Models FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Very low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.0 V to 3.6 V • Insensitive to supply voltage ripple and noise • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 23051 MECHANICAL DATA 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The TSOP93... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. The TSOP931.., TSOP933.., and TSOP935.., series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC3 provides enhanced noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. These components have not been qualified to automotive specifications. PARTS TABLE AGC 30 kHz 33 kHz Carrier 36 kHz frequency 38 kHz 40 kHz 56 kHz Package Pinning Dimensions (mm) Mounting Application Best choice for LEGACY, FOR SHORT BURSTS ENHANCED NOISE SUPPRESSION MAXIMIZED NOISE SUPPRESSION (AGC1) (AGC3) (AGC5) TSOP93130 TSOP93330 TSOP93530 TSOP93133 TSOP93333 TSOP93533 TSOP93136 TSOP93336 (1)(5) TSOP93536 TSOP93138 TSOP93338 (2)(4) TSOP93538 TSOP93140 TSOP93340 TSOP93540 TSOP93156 TSOP93356 TSOP93556 (3) Minimold 1 = OUT, 2 = GND, 3 = VS 5.4 W x 6.35 H x 4.9 D Leaded Remote control (1) RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2 (5) MCIR Note • 30 kHz and 33 kHz only available on written request Rev. 1.4, 31-Jul-2019 1 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 www.vishay.com BLOCK DIAGRAM 16833-13 30 kΩ Input AGC Band pass Demodulator PIN Control circuit TSOP931.., TSOP933.., TSOP935.. Vishay Semiconductors APPLICATION CIRCUIT 17170-12 3 R1 Transmitter IR receiver with TSALxxxx VS + VS 1 C1 OUT μC Circuit GND VO GND 2 R1 and C1 recommended to reduce supply ripple for VS < 2.2 V ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE UNIT Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case VS IS VO IO Tj Tstg Tamb Ptot Tsd -0.3 to +3.6 3 -0.3 to (VS + 0.3) 5 100 -25 to +85 -25 to +85 10 260 V mA V mA °C °C °C mW °C Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. Supply current Supply voltage Transmission distance Output voltage low Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 ISD ISH VS d VOSL 0.25 - 2.0 - - 0.37 0.50 28 - 0.45 3.6 - 100 Minimum irradiance Test signal: XMP code Test signal: NEC code Ee min. - 0.12 0.25 0.09 0.20 Maximum irradiance tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee max. 30 - - Directivity Angle of half transmission distance ϕ1/2 - ± 45 - UNIT mA mA V m mV mW/m2 W/m2 ° Rev. 1.4, 31-Jul-2019 2 Document Number: 82840 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 www.vishay.com TSOP931.., TSOP933.., TSOP935.. Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) 1st line 2nd line Ee Optical Test Signal (IR diode TSAL6200, N = 6 pul.


TSOP93538 TSOP93540 TSOP93556


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)