TSOP94640 Modules Datasheet

TSOP94640 Datasheet PDF, Equivalent


Part Number

TSOP94640

Description

IR Receiver Modules

Manufacture

Vishay

Total Page 7 Pages
PDF Download
Download TSOP94640 Datasheet PDF


TSOP94640
www.vishay.com
TSOP946..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
1
2
3
DESIGN SUPPORT TOOLS
16672
click logo to get started
Models
Available
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Supply voltage: 2.0 V to 3.6 V
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
MECHANICAL DATA
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP94... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.
These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the
presence of optical disturbances e.g. from CFLs.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The
demodulated output signal can be directly connected to a microprocessor for decoding.
The TSOP946.., series devices are designed to receive long burst codes (10 or more carrier cycles per burst). The third digit
designates the AGC level (AGC6) and the last two digits designate the band-pass frequency (see table below). The higher the
AGC, the better noise is suppressed, but the lower the code compatibility. AGC6 provides maximized noise suppression.
Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code.
These components have not been qualified to automotive specifications.
PARTS TABLE
AGC
Carrier frequency
Package
Pinning
Dimensions (mm)
Mounting
Application
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
Best choice for
MAXIMIZED NOISE SUPPRESSION
(AGC6)
TSOP94630
TSOP94633
TSOP94636 (5)(6)
TSOP94638 (3)(4)(11)
TSOP94640
TSOP94656
Mold
1 = OUT, 2 = GND, 3 = VS
6.0 W x 6.95 H x 5.6 D
Leaded
Remote control
(1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
Notes
• 30 kHz and 33 kHz only available on written request
• See datasheet for TSOP942.., TSOP944.. for preferred devices for (1)(2)(7)(8)(9)(10)(12)
Rev. 1.1, 11-Dec-2018
1 Document Number: 82836
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TSOP94640
www.vishay.com
BLOCK DIAGRAM
16833-13
30 kΩ
Input
AGC
Band
pass
Demo-
dulator
PIN Control circuit
3
1
2
TSOP946..
Vishay Semiconductors
APPLICATION CIRCUIT
17170-12
Transmitter
with
TSALxxxx
IR receiver
VS
OUT
GND
R1
C1
VO
+ VS
μC
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.2 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Supply current
Output voltage
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tamb 85 °C
t 10 s, 1 mm from case
VS
IS
VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
-0.3 to +3.6
3
-0.3 to (VS + 0.3)
5
100
-25 to +85
-25 to +85
10
260
V
mA
V
mA
°C
°C
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Supply current
Supply voltage
Transmission distance
Output voltage low
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
ISD
ISH
VS
d
VOSL
0.25
-
2.0
-
-
0.37
0.50
-
35
-
0.45
-
3.6
-
100
Minimum irradiance
Maximum irradiance
Test signal: NEC code
tpi - 5/f0 < tpo < tpi + 6/f0,
test signal see Fig. 1
Ee min.
Ee max.
-
30
0.06 0.12
--
Directivity
Angle of half transmission
distance
ϕ1/2
-
± 45
-
UNIT
mA
mA
V
m
mV
mW/m2
W/m2
°
Rev. 1.1, 11-Dec-2018
2 Document Number: 82836
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


Features www.vishay.com TSOP946.. Vishay Semicon ductors IR Receiver Modules for Remote Control Systems 1 2 3 DESIGN SUPPORT TOOLS 16672 click logo to get started Models Available FEATURES • Improve d dark sensitivity • Improved immunit y against optical noise • Very low su pply current • Photo detector and pre amplifier in one package • Internal f ilter for PCM frequency • Supply volt age: 2.0 V to 3.6 V • Insensitive to supply voltage ripple and noise • Mat erial categorization: for definitions o f compliance please see www.vishay.com/ doc?99912 MECHANICAL DATA 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The TSOP94... series devices are the latest generatio n miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitiv ity to remote control signals in dark a mbient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The devices contain a PIN di ode and a preamplifier assembled on a lead frame. The epoxy package contains an.
Keywords TSOP94640, datasheet, pdf, Vishay, IR, Receiver, Modules, SOP94640, OP94640, P94640, TSOP9464, TSOP946, TSOP94, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)