TSOP98640 Modules Datasheet

TSOP98640 Datasheet PDF, Equivalent


Part Number

TSOP98640

Description

IR Receiver Modules

Manufacture

Vishay

Total Page 8 Pages
Datasheet
Download TSOP98640 Datasheet


TSOP98640
www.vishay.com
TSOP986..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
1
2
3
19026
DESIGN SUPPORT TOOLS click logo to get started
Models
Available
FEATURES
• Improved dark sensitivity
• Improved immunity against optical noise
• Very low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Low supply voltage: 2.0 V to 3.6 V
• Insensitive to supply voltage ripple and noise
• Material categorization:
for definitions of compliance please see
www.vishay.com/doc?99912
MECHANICAL DATA
1 = OUT, 2 = GND, 3 = VS
DESCRIPTION
The TSOP98... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems.
This series provides improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence
of optical disturbances e.g. from CFLs.
The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The
demodulated output signal can be directly connected to a microprocessor for decoding.
The TSOP986.. series devices are designed to receive long burst codes (10 or more carrier cycles per burst). The third digit
designates the AGC level (AGC6) and the last two digits designate the band-pass frequency (see table below). The higher the
AGC, the better noise is suppressed, but the lower the code compatibility. AGC6 provides maximized noise suppression.
Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code.
These components have not been qualified to automotive specifications.
PARTS TABLE
AGC
Carrier frequency
Package
Pinning
Dimensions (mm)
Mounting
Application
30 kHz
33 kHz
36 kHz
38 kHz
40 kHz
56 kHz
Best choice for
MAXIMIZED NOISE SUPPRESSION
(AGC6)
TSOP98630
TSOP98633
TSOP98636 (5)(6)
TSOP98638 (3)(4)(11)
TSOP98640
TSOP98656
Minicast
1 = OUT, 2 = GND, 3 = VS
5.0 W x 6.95 H x 4.8 D
Leaded
Remote control
(1) Cisco (2) MCIR (3) Mitsubishi (4) NEC (5) Panasonic (6) RC-5 (7) RC-6
(8) RCA (9) r-step (10) Sejin 4PPM (11) Sharp (12) Sony
Notes
• 30 kHz and 33 kHz only available on written request
• See datasheet for TSOP982.., TSOP984.. for preferred devices for (1)(2)(7)(8)(9)(10)(12)
Rev. 1.1, 11-Dec-2018
1 Document Number: 82832
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000

TSOP98640
www.vishay.com
BLOCK DIAGRAM
16833-13
30 kΩ
Input
AGC
Band
pass
Demo-
dulator
PIN Control circuit
3
1
2
TSOP986..
Vishay Semiconductors
APPLICATION CIRCUIT
17170-12
Transmitter
with
TSALxxxx
IR receiver
VS
OUT
GND
R1
C1
VO
+ VS
μC
GND
R1 and C1 recommended to reduce supply ripple for VS < 2.2 V
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage
Supply current
Output voltage
Output current
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
Soldering temperature
Tamb 85 °C
t 10 s, 1 mm from case
VS
IS
VO
IO
Tj
Tstg
Tamb
Ptot
Tsd
-0.3 to +3.6
3
-0.3 to (VS + 0.3)
5
100
-25 to +85
-25 to +85
10
260
V
mA
V
mA
°C
°C
°C
mW
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL MIN.
TYP.
MAX.
Supply current
Supply voltage
Transmission distance
Output voltage low
Minimum irradiance
Maximum irradiance
Directivity
Ev = 0, VS = 3.3 V
Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1,
IR diode TSAL6200, IF = 50 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1
Test signal: NEC code
tpi - 5/f0 < tpo < tpi + 6/f0, test signal see Fig. 1
Angle of half transmission distance
ISD
ISH
VS
d
VOSL
Ee min.
Ee max.
ϕ1/2
0.25
-
2.0
-
-
-
30
-
0.37
0.50
-
24
-
0.12
-
± 45
0.45
-
3.6
-
100
0.25
-
-
UNIT
mA
mA
V
m
mV
mW/m2
W/m2
°
Rev. 1.1, 11-Dec-2018
2 Document Number: 82832
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000


Features www.vishay.com TSOP986.. Vishay Semicon ductors IR Receiver Modules for Remote Control Systems 1 2 3 19026 DESIGN SUPPORT TOOLS click logo to get started Models Available FEATURES • Improv ed dark sensitivity • Improved immuni ty against optical noise • Very low s upply current • Photo detector and pr eamplifier in one package • Internal filter for PCM frequency • Low supply voltage: 2.0 V to 3.6 V • Insensitiv e to supply voltage ripple and noise Material categorization: for definiti ons of compliance please see www.vishay .com/doc?99912 MECHANICAL DATA 1 = OUT, 2 = GND, 3 = VS DESCRIPTION The TSOP9 8... series devices are the latest gene ration miniaturized IR receiver modules for infrared remote control systems. T his series provides improvements in sen sitivity to remote control signals in d ark ambient as well as in sensitivity i n the presence of optical disturbances e.g. from CFLs. The devices contain a P IN diode and a preamplifier assembled on a lead frame. The epoxy package contai.
Keywords TSOP98640, datasheet, pdf, Vishay, IR, Receiver, Modules, SOP98640, OP98640, P98640, TSOP9864, TSOP986, TSOP98, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)