FLTR100V10 Module Datasheet

FLTR100V10 Datasheet, PDF, Equivalent


Part Number

FLTR100V10

Description

Filter Module

Manufacture

GE

Total Page 12 Pages
Datasheet
Download FLTR100V10 Datasheet


FLTR100V10
GE
Critical Power
FLTR100V10 Filter Module
75 Vdc Input Maximum,
10 A Maximum
RoHS Compliant
The FLTR100V10 Filter Module
is designed to reduce the
conducted common-mode and
differential-mode noise on input or
output lines of high-frequency switching
power supplies. The module has a
maximum current rating of 10 A. It
provides high insertion loss throughout
the frequency range regulated by the U.S.
Federal Communications Commission
(FCC) and the International Special
Committee on Radio Interference
(CISPR) for conducted emissions.
The module is 51 mm long, 28 mm wide,
and 12 mm high (2.0 in. x 1.1 in. x 0.46 in.)
and mounts on a PC board in a natural
convection or forced-air environment.
Introduction
High-density power modules are usually
designed to operate at a high switching
frequency to reduce the size of the
internal filter components. The small
EMI filters internal to the modules are
often inadequate to meet stringent
international EMI requirements. Many
high-density electronic packaging
techniques can increase the noise
conducted onto the modules’ input and
output lines. For example, the close
proximity of switching components to
the input pins increases internal noise
coupling; and planar transformers,
designed to handle high-power levels
in low- profile packages, have high
interwinding capacitance that can
increase common-mode current levels.
Also, metal substrates used to facilitate
heat transfer from the power train
components to an external heat sink add
to common-mode noise because of the
large capacitance between switching
components and the metal substrate.
Many international agencies specify
conducted and radiated emissions
limits for electronic products. Included
among these are CISPR, FCC, VCCI,
and the new CE specifications. Most
agency-conducted noise limits apply
only to noise currents induced onto
the ac power lines in finished products.
European Telecommunication Standard
Instructions (ETSI) are an exception,
applying CE requirements to dc supplies
with cables over three meters long.
Although not required to do so by agency
standards, some system designers apply
the conducted emissions requirements
to subassemblies within the product to
reduce internal interference between
subsystems and to reduce the difficulty
of meeting overall system requirements.
To meet these requirements, external
filtering of the power module is often
required. When used in conjunction with
the recommended external components
and layout, the Lineage Power filter
module will significantly reduce the
conducted differential and
common-mode noise returned to
the power source. CISPR and FCC
class B requirements can be met
by using the filter as described
in the following sections.
• Common-mode and differential-mode
filtering of power supply dc input and
output lines
• Computer applications
• Communications equipment
• Compliant to RoHS EU Directive
2011/65/EU
• Compatible in Pb- free or SnPb
reflow environment
• Small size: 51 mm x 28 mm x 12 mm
(2.0 in. x 1.1 in. x 0.46 in.)
• Optimized for use with high-frequency
dc-to-dc power modules
• Printed-circuit board mountable
• Operating case temperature range:
–40 °C to +100 °C
• CAN/CSA C22.2 No. 60950-1-07
/ UL* 60950-1, Second Edition,
dated March 27, 2007
• CE mark meets 73/23/EEC and 93/68/
EEC directives‡

FLTR100V10
Absolute Maximum Ratings
Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. These are absolute stress ratings
only. Functional operation of the device is not implied at these or any other conditions in excess of those given in the operations
sections of the data sheet. Exposure to absolute maximum ratings for extended periods can adversely affect device reliability.
PARAMETER
SYMBOL
MIN
Input Voltage:
Continuous
Transient (100 ms)
VI
VI, trans
Voltage from GND to Either Input Lead (1 minute)
——
Operating Case Temperature
Tc -40
Storage Temperature*
Tstg –55
* For the processing, handling and storage (module not powered), the filter module can handle -55°C to 125°C exposure.
MAX
75
100
1500
100
125
UNIT
Vdc
V
Vdc
°C
°C
Electrical Specifications
Unless otherwise indicated, specifications apply over all operating input voltage and temperature conditions.
PARAMETER
Resistance per Leg
Maximum Average Current
(TA = 60 °C, 2.0 m/s (400 lfm) air)
Maximum Average Current
(TA = 74 °C, natural convection)
Common-mode Insertion Loss
(50 Ω circuit, 500 kHz)
Differential-mode Insertion Loss
(50 Ω circuit, 500 kHz)
SYMBOL
MIN
TYP
MAX
R — — 14
I max
10
I max
6.5
— — 36 —
— — 44 —
UNIT
A
A
dB
dB
2 Filter Modules Datasheet | www.gecriticalpower.com


Features GE Critical Power FLTR100V10 Filter Mod ule 75 Vdc Input Maximum, 10 A Maximum RoHS Compliant The FLTR100V10 Filter M odule is designed to reduce the conduct ed common-mode and differential-mode no ise on input or output lines of high-fr equency switching power supplies. The m odule has a maximum current rating of 1 0 A. It provides high insertion loss th roughout the frequency range regulated by the U.S. Federal Communications Comm ission (FCC) and the International Spec ial Committee on Radio Interference (CI SPR) for conducted emissions. The modul e is 51 mm long, 28 mm wide, and 12 mm high (2.0 in. x 1.1 in. x 0.46 in.) and mounts on a PC board in a natural conv ection or forced-air environment. Intro duction High-density power modules are usually designed to operate at a high s witching frequency to reduce the size o f the internal filter components. The s mall EMI filters internal to the module s are often inadequate to meet stringen t international EMI requirements. Many high-density electronic .
Keywords FLTR100V10, datasheet, pdf, GE, Filter, Module, LTR100V10, TR100V10, R100V10, FLTR100V1, FLTR100V, FLTR100, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)