DS1099 Dual EconOscillator Datasheet

DS1099 Datasheet, PDF, Equivalent


Part Number

DS1099

Description

Low-Frequency Dual EconOscillator

Manufacture

Maxim Integrated

Total Page 7 Pages
Datasheet
Download DS1099 Datasheet


DS1099
DS1099
Low-Frequency Dual EconOscillator
General Description
The DS1099 is a low-cost, low-power, low-frequency
silicon oscillator that generates two square-wave out-
puts with frequencies between 0.25Hz and 1.048MHz.
Individual output enables allow both outputs to be
enabled/disabled independently. Both outputs are
capable of sinking 16mA, allowing them to directly
interface to light-emitting diodes (LEDs) as well as other
external circuitry. The DS1099 operates over a wide
supply voltage, making it suitable for both 3V and 5V
systems. The device is shipped from the factory custom
programmed and calibrated, ready to be inserted into
the end application.
Contact the factory for custom frequencies or require-
ments.
Applications
● Flashing LED Status Indicators
● Consumer Appliances
● Servers
● Printers
● Switch-Mode Power Supplies
Features
● Low-Cost, Low-Frequency EconOscillator™ with
Dual Outputs
● Factory Programmed
● Output Frequencies Independently Programmable
from 0.25Hz to 1.048MHz
● 2.7V to 5.5V Single-Supply Operation
● No External Timing Components Required
● Independent Output Enables
● CMOS/TTL-Compatible Outputs
● Oscillator Outputs Capable of Sinking 16mA to
Directly Drive LEDs
● Relieves Microprocessor of Periodic Interrupt
● Low-Power Consumption
● Operating Temperature Range: -40°C to +125°C
● ±100ppm/°C Temp Drift (max)
Ordering Information
PART
TEMP RANGE
PIN-PACKAGE
DS1099U- a O a 1 -40°C to +125°C
8 µSOP
*Where α 0 and α 1 specify the factory-programmed divider
settings for OUT0 and OUT1, respectively.
Ordering information is continued on the last page.
EconOscillator is a trademark of Maxim Integrated Products, Inc.
Typical Operating Circuit
VCC VCC
VCC
OE0
OE1
DS1099 OUT0
N.C. OUT1
N.C. GND
OE1 CAN INSTEAD
BE TIED TO VCC
IF OUT1 IS NOT USED.
OUTPUTS CAPABLE OF
SINKING 16mA
Pin Configuration
TOP VIEW
OUT1 1
OUT0 2
VCC 3
GND 4
DS1099
µSOP
8 N.C.
7 N.C.
6 OE1
5 OEO
19-7629; Rev 2; 5/15

DS1099
DS1099
Low-Frequency Dual EconOscillator
Absolute Maximum Ratings
Voltage Range on VCC Relative to Ground..........-0.5V to +6.0V
Voltage Range on OE0 and OE1
Relative to Ground................................... -0.5V to (VCC + 0.5V),
not to exceed 6.0V
Operating Temperature Range.......................... -40°C to +125°C
Storage Temperature Range............................. -55°C to +125°C
Soldering Temperature.......................................See IPC/JEDEC
J-STD-020A Specification
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these
or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect
device reliability.
Recommended DC Operating Conditions
(TA = -40°C to +125°C)
PARAMETER
Supply Voltage
SYMBOL
VCC
(Note 1)
CONDITIONS
Input Logic 1 (OE0, OE1)
VIH
Input Logic 0 (OE0, OE1)
VIL
MIN
2.7
0.7 x
VCC
-0.3
TYP
MAX
5.5
VCC +
0.3
+0.3 x
VCC
UNITS
V
V
V
DC Electrical Characteristics
(VCC = +2.7V to +5.5V, TA = -40°C to +125°C, unless otherwise noted.)
PARAMETER
Standby Supply Current
Active Supply Current (Note 2)
High-Level Output Voltage
(OUT0, OUT1)
Low-Level Output Voltage
(OUT0, OUT1)
High-Level Input Current
(OE0, OE1)
Low-Level Input Current
(OE0, OE1)
SYMBOL
ISTBY
ICC
CONDITIONS
OE0 = OE1 = VCC
CL = 15pF per output, 1.048MHz (both)
OE0 = OE1 = GND,
4kHz (both)
VCC = 3.3V
1Hz (both)
VOH IOH = -1mA, VCC = MIN
VOL
IOL = 16mA (-40°C to +85°C)
IOL = 12mA (-40°C to +125°C)
IIH VIH = VCC
MIN
2.4
IIL VIL = 0.0V
-1.0
TYP
145
323
146
145
MAX UNITS
275 µA
µA
0.4
+1.0
V
V
µA
µA
www.maximintegrated.com
Maxim Integrated 2


Features DS1099 Low-Frequency Dual EconOscillato r General Description The DS1099 is a low-cost, low-power, low-frequency sili con oscillator that generates two squar e-wave outputs with frequencies between 0.25Hz and 1.048MHz. Individual output enables allow both outputs to be enabl ed/disabled independently. Both outputs are capable of sinking 16mA, allowing them to directly interface to light-emi tting diodes (LEDs) as well as other ex ternal circuitry. The DS1099 operates o ver a wide supply voltage, making it su itable for both 3V and 5V systems. The device is shipped from the factory cust om programmed and calibrated, ready to be inserted into the end application. C ontact the factory for custom frequenci es or requirements. Applications ●● Flashing LED Status Indicators ●● Consumer Appliances ●● Servers ● Printers ●● Switch-Mode Power Su pplies Features ●● Low-Cost, Low-F requency EconOscillator™ with Dual Ou tputs ●● Factory Programmed ●● Output Frequencies Independently Programmable from 0.25Hz .
Keywords DS1099, datasheet, pdf, Maxim Integrated, Low-Frequency, Dual, EconOscillator, S1099, 1099, 099, DS109, DS10, DS1, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)