Document
®
Data Sheet
EL2250, EL2450
May 19, 2006
FN7061.3
125MHz Single Supply Dual/Quad Op Amps
The EL2250/EL2450 are part of a family of the electronics industries fastest single supply op amps available. Prior single supply op amps have generally been limited to bandwidths and slew rates to that of the EL2250/EL2450. The 125MHz bandwidth, 275V/µs slew rate, and 0.05%/0.05° differential gain/differential phase makes this part ideal for single or dual supply video speed applications. With its voltage feedback architecture, this amplifier can accept reactive feedback networks, allowing them to be used in analog filtering applications. The inputs can sense signals below the bottom supply rail and as high as 1.2V below the top rail. Connecting the load resistor to ground and operating from a single supply, the outputs swing completely to ground without saturating. The outputs can also drive to within 1.2V of the top rail. The EL2250/EL2450 will output ±100mA and will operate with single supply voltages as low as 2.7V, making them ideal for portable, low power applications.
The EL2250/EL2450 are available in PDIP and SO packages in industry standard pin outs. Both parts operate over the industrial temperature range of -40°C to +85°C, and are part of a family of single supply op amps. For single amplifier applications, see the EL2150/EL2157. For dual and triple amplifiers with power down and output voltage clamps, see the EL2257/EL2357.
Ordering Information
PART TAPE &
PKG.
PART NUMBER MARKING REEL PACKAGE DWG. #
EL2250CN
EL2250CN - 8 Ld PDIP MDP0031
EL2250CS
2250CS
- 8 Ld SO MDP0027
EL2250CS-T7 2250CS
7” 8 Ld SO MDP0027
EL2250CS-T13 2250CS
13” 8 Ld SO MDP0027
EL2250CSZ (Note)
2250CSZ
- 8 Ld SO MDP0027 (Pb-free)
EL2250CSZ-T7 2250CSZ (Note)
7” 8 Ld SO MDP0027 (Pb-free)
EL2250CSZ-T13 2250CSZ (Note)
13” 8 Ld SO MDP0027 (Pb-free)
EL2450CN
EL2450CN - 14 Ld PDIP MDP0031
EL2450CS
2450CS
- 14 Ld SO MDP0027
EL2450CS-T7 2450CS
7” 14 Ld SO MDP0027
EL2450CS-T13 2450CS
13” 14 Ld SO MDP0027
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Features
• Specified for +3V, +5V, or ±5V applications • Large input common mode range
0V < VCM < VS -1.2V • Output swings to ground without saturating • -3dB bandwidth = 125MHz • ±0.1dB bandwidth = 30MHz • Low supply current = 5mA (per amplifier) • Slew rate = 275V/µs • Low offset voltage = 4mV max • Output current = ±100mA • High open loop gain = 80dB • Differential gain = 0.05% • Differential phase = 0.05° • Pb-free plus anneal available (RoHS compliant)
Applications
• Video amplifiers • PCMCIA applications • A/D drivers • Line drivers • Portable computers • High speed communications • RGB printers, FAX, scanners • Broadcast equipment • Active filtering
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2002-2006. All Rights Reserved. All other trademarks mentioned are the property of their respective owners.
12348765-AO9B 2B U+ TAC 1O
UA T
F
2
EL2250, EL2450
Absolute Maximum Ratings (TA = 25°C)
Supply Voltage between VS and GND . . . . . . . . . . . . . . . . . . +12.6V Input Voltage (IN+, IN-) . . . . . . . . . . . . . . . . . . . GND-0.3V,VS+0.3V Differential Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±6V Maximum Output Current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90mA Output Short Circuit Duration. . . . . . . . . . . . . . . . . . . . . . . . (Note 1)
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves Storage Temperature Range . . . . . . . . . . . . . . . . . .-65°C to +150°C Ambient Operating Temperature Range . . . . . . . . . .-40°C to +85°C Operating Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . 150°C
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications VS = +5V, GND = 0V, TA = 25°C, VCM = 1.5V, VOUT = 1.5V, unless othe.