OPERATIONAL AMPLIFIER. TLE2141-Q1 Datasheet

TLE2141-Q1 AMPLIFIER. Datasheet pdf. Equivalent

Part TLE2141-Q1
Description LOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIER
Feature TLE2141-Q1 www.ti.com SLOS525 – SEPTEMBER 2011 Excalibur™ LOW-NOISE HIGH-SPEED PRECISION OPERATIO.
Manufacture etcTI
Datasheet
Download TLE2141-Q1 Datasheet



TLE2141-Q1
TLE2141-Q1
www.ti.com
SLOS525 SEPTEMBER 2011
ExcaliburLOW-NOISE HIGH-SPEED PRECISION OPERATIONAL AMPLIFIERS
Check for Samples: TLE2141-Q1
FEATURES
1
2 Qualified for Automotive Applications
Low Noise
10 Hz 15 nV/Hz
1 kHz 10.5 nV/Hz
10000-pF Load Capability
20-mA Min Short-Circuit Output Current
27-V/μs Slew Rate (Min)
High Gain-Bandwidth Product 5.9 MHz
Low VIO 500 μV (Max) at 25°C
Single or Split Supply 4 V to 44 V
Fast Settling Time
340 ns to 0.1%
400 ns to 0.01%
Saturation Recovery 150 ns
Large Output Swing
VCC+ 0.1 V to VCC+ 1 V
DESCRIPTION
The TLE2141-Q1 device is a high-performance, internally compensated operational amplifier built using the
Texas Instruments complementary bipolar Excaliburprocess. It is a pin-compatible upgrade to standard
industry products.
The design incorporates an input stage that simultaneously achieves low audio-band noise of 10.5 nV/Hz with a
10-Hz 1/f corner and symmetrical 40-V/μs slew rate typically with loads up to 800 pF. The resulting low distortion
and high power bandwidth are important in high-fidelity audio applications. A fast settling time of 340 ns to 0.1%
of a 10-V step with a 2-k/100-pF load is useful in fast actuator/positioning drivers. Under similar test conditions,
settling time to 0.01% is 400 ns.
The device is stable with capacitive loads up to 10 nF, although the 6-MHz bandwidth decreases to 1.8 MHz at
this high loading level. As such, the TLE2141-Q1 is useful for low-droop sample-and-holds and direct buffering of
long cables, including 4-mA to 20-mA current loops.
The special design also exhibits an improved insensitivity to inherent integrated circuit component mismatches as
is evidenced by a 500-μV maximum offset voltage and 1.7-μV/°C typical drift. Minimum common-mode rejection
ratio and supply-voltage rejection ratio are 85 dB and 90 dB, respectively.
Device performance is relatively independent of supply voltage over the ±2-V to ±22-V range. Inputs can operate
between VCC0.3 V to VCC+ 1.8 V without inducing phase reversal, although excessive input current may flow
out of each input exceeding the lower common-mode input range. The all-npn output stage provides a nearly
rail-to-rail output swing of VCC0.1 V to VCC+ 1 V under light current-loading conditions. The device can
sustain shorts to either supply since output current is internally limited, but care must be taken to ensure that
maximum package power dissipation is not exceeded.
The TLE2141-Q1 device can also be used as a comparator. Differential inputs of VCC± can be maintained without
damage to the device. Open-loop propagation delay with TTL supply levels is typically 200 ns. This gives a good
indication as to output stage saturation recovery when the device is driven beyond the limits of recommended
output swing.
The TLE2141-Q1 device is available in industry-standard 8-pin package. The device is characterized for
operation from 40°C to 125°C.
TA
40°C to 125°C
ORDERING INFORMATION(1)
PACKAGE
ORDERABLE PART NUMBER
SOIC D (8 pin)
Reel of 2500
TLE2141QDRQ1
TOP-SIDE MARKING
2141Q
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Excalibur is a trademark of Texas Instruments.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated



TLE2141-Q1
TLE2141-Q1
SLOS525 SEPTEMBER 2011
SYMBOL
OFFSET N1
IN+
+
IN-
-
OFFSET N2
OUT
D PACKAGE
(TOP VIEW)
OFFSET N1 1
IN- 2
IN+ 3
VCC- 4
8 NC
7 VCC+
6 OUT
5 OFFSET N2
NC – No internal connection
www.ti.com
2
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated





@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)