Document
MCC
TM
Micro Commercial Components
omponents 20736 Marilla Street Chatsworth !"# $
% !"#
Features
x Zener Voltage From 5.1V to 51V • Epoxy meets UL 94 V-0 flammability rating • Moisture Sensitivity Level 1 • Lead Free Finish/RoHS Compliant (Note1) ("P"Suffix designates
Compliant. See ordering information) • Marking : Cathode band and type number
• Glass passivated junction
Maximum Ratings:
x Operating Temperature: -55qC to +150qC
x Storage Temperature: -55qC to +150qC
x 5 Watt DC Power Dissipation
x Maximum Forward Voltage @ 1A: 1.2 Volts
x Power Derating: 40 mW/к Above 75к x Maximum thermal resistence: 25C/W from junction to ambient
Mechanical Data
Case: JEDEC DO-15. Terminals: Solder plated , solderable per MIL-STD-750, Method 2026. Standard Packaging: 52mm tape
1N5338B-TPX01 THRU
1N5369B-TPX01
5 Watt Zener Diode 5.1 to 51 Volts
DO-15
D
A Cathode Mark B
D
Note: 1. High Temperature Solder Exemption Applied, see EU Directive Annex 7.
C
DIMENSIONS
INCHES
DIM
MIN
MAX
A
.230
.300
B
.104
.140
C
.026
.034
D
1.000
---
MM MIN 5.80 2.60 .70 25.40
MAX 7.60 3.60 .90 ---
NOTE
Revision: A
www.mccsemi.com
1 of 6
2011/01/01
1N5338B-TPX01 THRU 1N5369B-TPX01
ELECTRICAL CHARACTERISTICS (TA=25qC unless otherwise noted, VF=1.2 Max @ IF=1A for all types).
MCC TM
Micro Commercial Components
MCC PART NUMBER
REGULATOR VOLTAGE VZ
(Note2)
VOLTS
1N5338B-TPX01 5 .1 1N5339B-TPX01 5.6 1N5340B-TPX01 6.0 1N5341B-TPX01 6.2 1N5342B-TPX01 6.8 1N5343B-TPX01 7.5 1N5344B-TPX01 8.2 1N5345B-TPX01 8.7 1N5346B-TPX01 9.1 1N5347B-TPX01 10 1N5348B-TPX01 11 1N5349B-TPX01 12 1N5350B-TPX01 13 1N5351B-TPX01 14 1N5352B-TPX01 15 1N5353B-TPX01 16 1N5354B-TPX01 17 1N5355B-TPX01 18 1N5356B-TPX01 19 1N5357B-TPX01 20 1N5358B-TPX01 22 1N5359B-TPX01 24 1N5360B-TPX01 25 1N5361B-TPX01 27 1N5362B-TPX01 28 1N5363B-TPX01 30 1N5364B-TPX01 33 1N5365B-TPX01 36 1N5366B-TPX01 39 1N5367B-TPX01 43 1N5368B-TPX01 47 1N5369B-TPX01 51
TEST CURRENT
IZT
mA
240 220 200 200 175 175 150 150 150 125 125 100 100 100 75 75 70 65 65 65 50 50 50 50 50 40 40 30 30 30 25 25
MAXIMUM DYNAMIC IMPEDANCE ZZk (@IZT)
(Note2)
OHMS
1.5 1.0 1.0 1.0 1.0 1.5 1.5 2.0 2.0 2.0 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 3.0 3.0 3.5 3.5 4.0 5.0 6.0 8.0 10 11 14 20 25 27
MAXIMUM REVERSE CURRENT
IR
TEST VOLTAGE
VR
PA
1.0 1.0 1.0 1.0 10 10 10 10 7.5 5.0 5.0 2.0 1.0 1.0 1.0 1.0 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5
VOLTS
1.0 2.0 3.0 3.0 5.2 5.7 6.2 6.6 6.9 7.6 8.4 9.1 9.9 10.6 11.5 12.2 12.9 13.7 14.4 15.2 16.7 18.2 19 20.6 21.2 22.8 25.1 27.4 29.7 32.7 35.8 38.8
MAXIMUM REGULATOR
CURRENT IZM
(Note5)
mA
930 865 790 765 700 630 580 545 520 475 430 395 365 340 315 295 280 264 250 237 216 198 190 176 170 158 144 132 122 110 100 93
MAXIMUM DYNAMIC
KNEE IMPEDANCE ZZK@ 1.0mA
(Note2)
ohms
400 400 300 200 200 200 200 200 150 125 125 125 100 75 75 75 75 75 75 75 75 100 110 120 130 140 150 160 170 190 210 230
MAXIMUM SURGE
CURRENT Ir
(Note3)
A
14.4 13.4 12.7 12.4 11.5 10.7 10 9.5 9.2 8.6 8.0 7.5 7.0 6.7 6.3 6.0 5.8 5.5 5.3 5.1 4.7 4.4 4.3 4.1 3.9 3.7 3.5 3.3 3.1 2.8 2.7 2.5
MAXIMUM VOLTAGE REGULATION
(Note4)
VOLTS
0.39 0.25 0.19 0.10 0.15 0.15 0.20 0.20 0.22 0.22 0.25 0.25 0.25 0.25 0.25 0.30 0.35 0.40 0.40 0.40 0.45 0.55 0.55 0.60 0.60 0.60 0.60 0.65 0.65 0.70 0.80 0.90
NOTE: 1. TOLERANCE AND VOLTAGE DESIGNATION - The JEDEC type numbers shown indicate a tolerance of+/-10% with
guaranteed limits on only Vz, IR, Ir, and VF as shown in the electrical characteristics table. Units with guaranteed limits on all seven parameters are indicated by suffix “B” for+/-5% tolerance. 2. ZENER VOLTAGE (Vz) AND IMPEDANCE (ZZT & ZZK) - Test conditions for Zener voltage and impedance are as follows; Iz is applied 40+/-10 ms prior to reading. Mounting contacts are located from the inside edge of mounting clips to the body of the diode(Ta=25qC )
Revision: A
www.mccsemi.com
2 of 6
2011/01/01
1N5338B-TPX01 THRU 1N5369B-TPX01
MCC
TM
Micro Commercial Components
3. SURGE CURRENT (Ir) - Surge current is specified as the maximum allowable peak, non-recurrent square-wave current with a pulse width, PW, of 8.3 ms. The data given in Figure 5 may be used to find the maximum surge current for a quare wave of any pulse width between 1 ms and 1000ms by plotting the applicable points on logarithmic paper. Examples of this, using the 6.8v , is shown in Figure 6. Mounting contact located as specified in Note 3. (TA=25 ć ).
4. VOLTAGE REGULATION (Vz) - Test conditions for voltage regulation are as follows: Vz measurements are made at 10% and then at 50% of the Iz max value listed in the electrical characteristics table. The test currents are the same for the 5% and 10% tolerance devices. The test current time druation for each Vz measurement is 40+/- 10 ms. (TA=25C ). Mounting contact located as specified in Note2.
5. MAXIMUM REGULATOR CURRENT (IZM) - The maximum current shown is based on the maximum voltage.