Document
SN74LS04 Hex Inverter
VCC 14 13 12 11 10 9 8
1234567 GND
GUARANTEED OPERATING RANGES
Symbol
Parameter
Min Typ Max Unit
VCC TA
Supply Voltage
Operating Ambient Temperature Range
4.75 5.0 5.25
V
0
25
70
°C
IOH
Output Current – High
IOL
Output Current – Low
– 0.4 mA
8.0
mA
http://onsemi.com
LOW POWER SCHOTTKY
14 1 PLASTIC N SUFFIX CASE 646
14 1
SOIC D SUFFIX CASE 751A
ORDERING INFORMATION
Device
Package
Shipping
SN74LS04N 14 Pin DIP 2000 Units/Box
SN74LS04D
14 Pin
2500/Tape & Reel
© Semiconductor Components Industries, LLC, 1999
1
December, 1999 – Rev. 6
Publication Order Number: SN74LS04/D
SN74LS04
DC CHARACTERISTICS OVER OPERATING TEMPERATURE RANGE (unless otherwise specified)
Limits
Symbol
Parameter
Min
Typ
Max
Unit
Test Conditions
VIH
Input HIGH Voltage
2.0
V
Guaranteed Input HIGH Voltage for All Inputs
VIL
Input LOW Voltage
0.8
V
Guaranteed Input LOW Voltage for All Inputs
VIK VOH
Input Clamp Diode Voltage Output HIGH Voltage
– 0.65
– 1.5
2.7
3.5
V
VCC = MIN, IIN = – 18 mA
V
VCC = MIN, IOH = MAX, VIN = VIH
or VIL per Truth Table
VOL
Output LOW Voltage
0.25
0.4
0.35
0.5
V
IOL = 4.0 mA VCC = VCC MIN,
VIN = VIL or VIH
V
IOL = 8.0 mA per Truth Table
IIH
Input HIGH Current
IIL
Input LOW Current
IOS
Short Circuit Current (Note 1)
– 20
Power Supply Current
ICC
Total, Output HIGH
Total, Output LOW
20 0.1 – 0.4 –100
2.4 6.6
µA
VCC = MAX, VIN = 2.7 V
mA
VCC = MAX, VIN = 7.0 V
mA
VCC = MAX, VIN = 0.4 V
mA
VCC = MAX
mA
VCC = MAX
Note 1: Not more than one output should be shorted at a time, nor for more than 1 second.
AC CHARACTERISTICS (TA = 25°C)
Symbol tPLH tPHL
Parameter Turn–Off Delay, Input to Output Turn–On Delay, Input to Output
Limits
Min
Typ
Max
Unit
9.0
15
ns
10
15
ns
Test Conditions
VCC = 5.0 V CL = 15 pF
http://onsemi.com 2
14
1
A F
N
–T–
SEATING PLANE
H
G
SN74LS04
PACKAGE DIMENSIONS
N SUFFIX PLASTIC PACKAGE
CASE 646–06 ISSUE M
8
B
7
L C
K
J
D 14 PL
M
0.13 (0.005) M
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. DIMENSION L TO CENTER OF LEADS WHEN FORMED PARALLEL. 4. DIMENSION B DOES NOT INCLUDE MOLD FLASH. 5. ROUNDED CORNERS OPTIONAL.
INCHES
MILLIMETERS
DIM MIN MAX MIN MAX
A 0.715 0.770 18.16 18.80
B 0.240 0.260 6.10 6.60
C 0.145 0.185 3.69 4.69
D 0.015 0.021 0.38 0.53
F 0.040 0.070 1.02 1.78
G 0.100 BSC
2.54 BSC
H 0.052 0.095 1.32 2.41
J 0.008 0.015 0.20 0.38
K 0.115 0.135 2.92 3.43
L 0.290 0.310 7.37
M ––– 10_ –––
7.87
10_
N 0.015 0.039 0.38 1.01
–A–
14 1
D SUFFIX PLASTIC SOIC PACKAGE
CASE 751A–03 ISSUE F
8
–B– P 7 PL 0.25 (0.010) M B M
7
G
C
R X 45 _
F
–T–
SEATING PLANE
D 14 PL
K
M
J
0.25 (0.010) M T B S A S
NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION.
MILLIMETERS
INCHES
DIM MIN MAX MIN MAX
A 8.55 8.75 0.337 0.344
B 3.80 4.00 0.150 0.157
C 1.35 1.75 0.054 0.068
D 0.35 0.49 0.014 0.019
F 0.40 1.25 0.016 0.049
G
1.27 BSC
0.050 BSC
J 0.19 0.25 0.008 0.009
K 0.10 0.25 0.004 0.009
M 0_ 7_ 0_ 7_
P 5.80 6.20 0.228 0.244
R 0.25 0.50 0.010 0.019
http://onsemi.com 3
SN74LS04
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes
without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular
purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability,
including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be
validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others.
SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or
death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold
SCILLC and its officers, employees, subsidiaries, affiliates, .