Document
CMOS Digital Integrated Circuits Silicon Monolithic
TC7SB3157DL6X
TC7SB3157DL6X
1. Functional Description
• Single 1-of-2 Multiplexer/Demultiplexer
2. General
The TC7SB3157DL6X is a high-speed CMOS single 1-of-2 multiplexer/demultiplexer. The low ON resistance of the switch allows connections to be made with minimal propagation delay time. This device is 1 to 2 multiplexer/demultiplexer controlled by the select input (S). The A input is connected to B1 or B2 output based on the selection of Control input (S). All inputs are equipped with protection circuits against static discharge.
3. Features
(1) Operating voltage: VCC = 1.65 to 5.5 V (2) ON capacitance: CI/O = 15 pF Switch On (typ.) @VCC = 5.0 V (3) ON resistance: RON = 4 Ω (typ.) @VCC = 4.5 V, VIS = 0 V (4) ESD performance: Machine model ≥ ±200 V, Human body model ≥ ±2000 V (5) Package: MP6D
4. Packaging
MP6D
©2017 Toshiba Corporation
1
Start of commercial production
2017-06
2017-06-05 Rev.2.0
5. Pin Assignment 6. Marking 7. Block Diagram
TC7SB3157DL6X
©2017 Toshiba Corporation
2
2017-06-05 Rev.2.0
8. Principle of Operation 8.1. Truth Table
TC7SB3157DL6X
Inputs S L H
9. Absolute Maximum Ratings (Note)
Function A port = B1 port A port = B2 port
Characteristics
Symbol Note
Rating
Unit
Supply voltage
VCC
-0.5 to 6.5
V
Input voltage (S)
VIN
-0.5 to 6.5
Switch I/O voltage
VS
-0.5 to VCC
Clamp diode current
IIK
-50
mA
Switch I/O current
IS
50
Power dissipation
PD (Note 1)
250
mW
VCC/ground current
ICC/IGND
±100
mA
Storage temperature
Tstg
-65 to 150
Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Note 1: Mounted on an FR4 board
10. Operating Ranges (Note)
Characteristics
Symbol Note
Rating
Unit
Supply voltage Input voltage(S) Switch I/O voltage Operating temperature Input rise time
VCC VIN VS Topr dt/dv
1.65 to 5.5 0 to 5.5 0 to VCC -40 to 85 0 to 10
V
ns/V
Input fall time
dt/dv
0 to 10
Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused control inputs must be tied to either VCC or GND.
©2017 Toshiba Corporation
3
2017-06-05 Rev.2.0
TC7SB3157DL6X
11. Electrical Characteristics 11.1. DC Characteristics (Unless otherwise specified, Ta = -40 to 85 )
Characteristics
Symbol Note
Test Condition
VCC (V)
Min Typ. Max Unit
High-level input voltage (S) VIH
Low-level input voltage (S) VIL
Input leakage current
IIN
Switch OFF-state leakage ISZ current
VIN = 0 to 5.5 V B1, B2 = 0 to VCC
1.65 to 1.95 0.8 × VCC
V
2.3 to 5.5 0.7 × VCC
1.65 to 1.95
0.2 × VCC
2.3 to 5.5
0.3 × VCC
1.65 to 5.5
±1.0 µA
1.65 to 5.5
±10
ON-resistance Quiescent supply current
RON
ICC ∆ICC
(Note 1), VIS = 0 V, IIS = 30 mA (Note 2) VIS = 2.4 V, IIS = 30 mA
VIS = 4.5 V, IIS = 30 mA VIS = 0 V, IIS = 24 mA VIS = 3.0 V, IIS = 24 mA VIS = 0 V, IIS = 8 mA VIS = 2.3 V, IIS = 8 mA VIS = 0 V, IIS = 4 mA VIS = 1.65 V, IIS = 4 mA VIN = VCC or GND, IOUT = 0 A VIN = VCC - 0.6 V
4.5 4.5 4.5 3.0 3.0 2.3 2.3 1.65 1.65 5.5 5.5
4
7
Ω
5
12
6
10
5
9
7
14
6
12
9
18
8
20
15
30
10
µA
50
µA
Note 1: All typical values are at Ta = 25 . Note 2: Measured by the voltage drop between A and B pins at the indicated current through the switch. On-resistance
is determined by the lower of the voltages on the two (A or B) pins.
11.2. AC Characteristics (Unless otherwise specified, Ta = -40 to 85 )
Characteristics 3-state output enable time
Symbol tPZL/tPZH
Note
Test Condition
See Fig. 11.2.1, 11.2.2, Table 11.2.1
3-state output disable time
tPLZ/tPHZ
See Fig. 11.2.1, 11.2.2, Table 11.2.1
VCC (V)
Min
Max Unit
5.0 ± 0.5
4
ns
3.3 ± 0.3
6
2.5 ± 0.2
8
1.8 ± 0.15
16
5.0 ± 0.5
4.5
3.3 ± 0.3
7
2.5 ± 0.2
9
1.8 ± 0.15
16
11.3. Capacitive Characteristics (Note) (Unless otherwise specified, Ta = 25 )
Characteristics
Input capacitance(S) Switch terminal OFF-capacitance Switch terminal ON-capacitance
Symbol
CIN CI/O CI/O
Note: Parameter guaranteed by design.
Note
Test Condition
VIN = 0 V B Port,VI/O = 0 V A Port,VI/O = 0 V B Port,VI/O = 0 V
VCC (V) Ty.