Document
TC7SH07FS
TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic
TC7SH07FS
NON-Inverter (Open Drain)
Features
• High speed: tpZL = 3.7ns (typ.) at VCC = 5V, 15pF • Low power dissipation: ICC = 2μA (max) at Ta = 25°C • Wide operating voltage range: VCC = 2 to 5.5V • 5.5-V tolerant input • 5.5-V power down protection output
SON5-P-0.35
Weight : 0.001 g (Typ.)
(fSV)
Marking
HM
Product Name
Pin Assignment (top view)
IN A 1
5 VCC
GND 2
NC 3
4 OUT Y
Absolute Maximum Ratings ( Ta = 25°C)
Characteristics
Symbol
Rating
Unit
Supply voltage range DC input voltage DC output voltage Input diode current Output diode current DC output current DC VCC/ground current Power dissipation Storage temperature
VCC VIN VOUT IIK IOK IOUT ICC PD Tstg
− 0.5 to 7
V
− 0.5 to 7
V
− 0.5 to 7 (Note 1) V
− 20
mA
− 20 (Note 2) mA
25
mA
± 50
mA
50
mW
− 65 to 150
°C
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc).
Note 1: Do not exceed IOUT of absolute maximum ratings. Note 2: VOUT < GND
Start of commercial production
2008-02
1
2014-03-01
IEC Logic Symbol
IN A
1
Operating Ranges
Characteristics Supply voltage Input voltage Output voltage Operating temperature
Input rise and fall time
Truth Table
OUT Y
A
Y
L
L
H
Z
Z: High impedance
TC7SH07FS
Symbol
VCC VIN VOUT Topr
dt/dv
Rating
2 to 5.5 0 to 5.5 0 to VCC −40 to 85 0 to 100 (VCC = 3.3 ± 0.3 V) 0 to 20 (VCC = 5.0 ± 0.5 V)
Unit V V V °C
ns/V
2
2014-03-01
TC7SH07FS
Electrical Characteristics
DC Characteristics
Characteristics Symbol
Test Condition
High-level input voltage
VIH
⎯
Low-level input voltage
VIL
⎯
Low-level output voltage
Input leakage current Output Z level leakage current
Power-off leakage current Quiescent supply current
VOL
IIN ILKG IOFF ICC
VIN = VIL
IOL = 50 μA
IOL = 4 mA IOL = 8 mA
VIN = 5.5 V or GND
VIN = VIH VOUT = 0 to 5.5V
VIN = 5.5V or VOUT = 0 to 5.5V
VIN = VCC or GND
VCC (V) 2.0
3.0 to 5.5
2.0 3.0 to 5.5
2.0 3.0 4.5 3.0 4.5
Ta = 25°C
Ta = −40 to 85°C Unit
Min Typ. Max Min Max
1.5
⎯
⎯
1.5
⎯
VCC × 0.7
⎯
⎯
VCC × 0.7
⎯
V
⎯
⎯
0.5
⎯
0.5
⎯
⎯
VCC × 0.3
⎯
VCC
V
× 0.3
⎯
0
0.1
⎯
0.1
⎯
0
0.1
⎯
0.1
⎯
0
0.1
⎯
0.1
V
⎯
⎯ 0.36
⎯
0.44
⎯
⎯ 0.36
⎯
0.44
0 to 5.5
⎯
⎯ ±0.1
⎯
±1.0 μA
0 to 5.5
⎯
⎯ ±0.25 ⎯
±2.5 μA
0.0
⎯
⎯
1.0
⎯
10.0 μA
5.5
⎯
⎯
2.0
⎯
20 μA
3
2014-03-01
TC7SH07FS
AC Characteristics (unless otherwise specified, Input: tr = tf = 3 ns)
Characteristics Propagation delay time
Symbol
Test Condition VCC (V)
tpZL RL = 1kΩ
3.3 ± 0.3 5.0 ± 0.5
tpLZ RL = 1kΩ
3.3 ± 0.3 5.0 ± 0.5
CL (pF) 15 50 15 50 15 50 15 50
Ta = 25°C
Min Typ. Max
⎯
5.5 7.9
⎯
8.0 11.4
⎯
3.7 5.5
⎯
5.2 7.5
⎯
5.5 7.9
⎯
8.0 11.4
⎯
3.7 5.5
⎯
5.2 7.5
Ta = −40 to 85°C Unit
Min Max
1.0
9.5
1.0
13.0
1.0
6.5
1.0
8.5
ns
1.0
9.5
1.0
13.0
1.0
6.5
1.0
8.5
Input capacitance
Output capacitance
Power dissipation capacitance
CIN COUT CPD
⎯
⎯
4
10
⎯
10 pF
⎯
⎯
6
⎯
⎯
⎯
pF
(Note3) ⎯
14
⎯
⎯
⎯
pF
Note 3: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load.
Average operating current can be obtained by the equation:
ICC (opr.) = CPD・VCC・fIN + ICC
4
2014-03-01
Package Dimensions
SON5-P-0.35
TC7SH07FS
Unit: mm
Weight: 0.001 g (typ.)
5
2014-03-01
TC7SH07FS
RESTRICTIONS ON PRODUCT USE
• Toshiba Corporation, and its subsidiaries and affiliates (collectively "TOSHIBA"), reserve the right to make changes to the information in this document, and related hardware, software and systems (collectively "Product") without notice.
• This document and any information herein may not be reproduced without prior written permission from TOSHIBA. Even with TOSHIBA's written permission, reproduction is permissible only if reproduction is without alteration/omission.
• Though TOSHIBA works continually to improve Product's quality and reliability, Product can malfunction or fail. Customers are responsible for complying with safety standards and for providing adequate designs and safeguards for their hardware, software and systems which minimize risk and avoid situations in which a malfunction or failure of Product.