Document
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146..
www.vishay.com
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
DESCRIPTION
This IR receiver series is optimized for long burst remote control systems in different environments. The customer can chose between different IC settings (AGC variants), to find the optimum solution for his application. The higher the AGC, the better noise is suppressed, but the lower the code compatibility.
The devices contain a PIN diode and a preamplifier
assembled on a lead frame. The epoxy package contains an
IR filter. The demodulated output signal can be directly
connected to a microprocessor for decoding. These
23196
components have not been qualified to automotive
specifications.
LINKS TO ADDITIONAL RESOURCES
Product Page
Marking
Packages
Holders
Bends and Cuts
FEATURES • Individual IC settings to reach maximum
performance • Immunity against noise (lamps, LCD TV, Wi-Fi) • Low supply current • Photo detector and preamplifier in one package • Supply voltage: 2.0 V to 5.5 V • Material categorization:
for definitions of compliance please see www.vishay.com/doc?99912
APPLICATIONS • Infrared remote control systems
DESIGN SUPPORT TOOLS • 3D models • Window size calculator
BLOCK DIAGRAM
30 kΩ
Input
AGC
Band pass
Demodulator
PIN
16833-22
Control circuit
VS OUT GND
Rev. 2.0, 16-Aug-2022
1
Document Number: 82803
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146..
www.vishay.com
Vishay Semiconductors
MECHANICAL DATA Pinning for TSOP14...: 1 = OUT, 2 = GND, 3 = VS Pinning for TSOP12...: 1 = OUT, 2 = VS, 3 = GND
ORDERING CODE TSOP12..., TSOP14... - 2160 pieces in tubes
APPLICATION CIRCUIT
17170-14
Transmitter IR receiver
with TSALxxxx
VS
Circuit
OUT GND
R1
C1 VO
+ VS μC
GND
1 2 3
23198
R1 and C1 recommended in case there are strong ripple or spikes on the supply line.
PARTS TABLE
AGC
BASIC NOISE SUPPRESSION (AGC2)
ENHANCED NOISE SUPPRESSION (AGC4)
MAXIMIZED NOISE SUPPRESSION (AGC6)
30 kHz TSOP14230 TSOP12230
TSOP14430
TSOP12430
TSOP14630 TSOP12630
33 kHz TSOP14233 TSOP12233
TSOP14433
TSOP12433
TSOP14633 TSOP12633
Carrier
36 kHz TSOP14236
frequency 38 kHz TSOP14238
TSOP12236 TSOP12238
TSOP14436 (4)(6)
TSOP12436 (4)(6) TSOP14636 (5) TSOP12636 (5)
TSOP14438 (2)(3)(9)(10) TSOP12438 (2)(3)(9)(10) TSOP14638
TSOP12638
40 kHz TSOP14240 (11) TSOP12240 (11)
TSOP14440
TSOP12440
TSOP14640 TSOP12640
56 kHz TSOP14256 (1) TSOP12256 (1)
TSOP14456 (8)
TSOP12456 (8)
TSOP14656 (7) TSOP12656 (7)
Package
Mold
Pinning Dimensions (mm)
1 = OUT,
1 = OUT,
2 = GND, 3 = VS 2 = VS, 3 = GND
1 = OUT, 2 = GND, 3 = VS
1 = OUT, 2 = VS, 3 = GND
6.0 W x 6.95 H x 5.6 D
1 = OUT,
1 = OUT,
2 = GND, 3 = VS 2 = VS, 3 = GND
Mounting
Leaded
Application
Remote control
Best choice for
(1) Cisco (2) Mitsubishi (3) NEC (4) Panasonic (5) RC-5 (6) RC-6 (7) RCA (8) r-step (9) Sejin 4PPM (10) Sharp (11) Sony
Special options
• Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726
ABSOLUTE MAXIMUM RATINGS
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
Supply voltage Supply current Output voltage Output current Junction temperature Storage temperature range Operating temperature range Power consumption Soldering temperature
Tamb ≤ 85 °C t ≤ 10 s, 1 mm from case
VS
-0.3 to +6
V
IS
3
mA
VO
-0.3 to (VS + 0.3)
V
IO
5
mA
Tj
100
°C
Tstg
-25 to +85
°C
Tamb
-25 to +85
°C
Ptot
10
mW
Tsd
260
°C
Note
• Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability
Rev. 2.0, 16-Aug-2022
2
Document Number: 82803
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
Datasheet Values Refer to PCN-OPT-1224-2022
TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146..
www.vishay.com
Vishay Semiconductors
ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
Supply current Supply voltage Transmission distance Output voltage low
Ev = 0, VS = 3.3 V Ev = 40 klx, sunlight
Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see Fig. 1
ISD ISH VS d
VOSL.