DatasheetsPDF.com

AT16373G Dataheets PDF



Part Number AT16373G
Manufacturers ATMEL Corporation
Logo ATMEL Corporation
Description AT16373 Fast Logic 16-Bit Transparent Latch
Datasheet AT16373G DatasheetAT16373G Datasheet (PDF)

AT16373 Features • • • • • • • Fastest Propagation Speeds in the Industry TPD (F grade) = 2.5 ns, TPD (G grade) = 2.0 ns Maximum derating for capacitive loads 1.5ns/100 pF (F grade) and 1.1ns/100 pF (G grade) Very low ground bounce < 0.6V @ VCC =5.00V, Ta=25°C Excellent noise rejection Typical output skew ≤0.25ns Bus Hold circuitry to retain last active state during Tri-state™ Available in SSOP and TSSOP packages Description Atmel’s AT16373 devices provide maximum speed in temporary data stor.

  AT16373G   AT16373G



Document
AT16373 Features • • • • • • • Fastest Propagation Speeds in the Industry TPD (F grade) = 2.5 ns, TPD (G grade) = 2.0 ns Maximum derating for capacitive loads 1.5ns/100 pF (F grade) and 1.1ns/100 pF (G grade) Very low ground bounce < 0.6V @ VCC =5.00V, Ta=25°C Excellent noise rejection Typical output skew ≤0.25ns Bus Hold circuitry to retain last active state during Tri-state™ Available in SSOP and TSSOP packages Description Atmel’s AT16373 devices provide maximum speed in temporary data storage. They can be operated as either two separate 8 bit latches or as a single 16-bit latch by use of the output enable and the latch enable. The AT16373 has very low ground bounce and excellent input noise rejection, giving the user stable signals in a high speed environment. These devices can drive very large loads while operating in a high speed transparent mode. AT16373 Fast Logic™ 16-Bit Transparent Latch AT16373F AT16373G Functional Block Diagram (1) Note: 1. This 8-bit latch function is repeated a second time on each device. Pin Configurations Pin Names xOE xLE xDχ xOχ Descriptions Output Enable Input (Active Low) Latch Enable Inputs (Active High) Data Inputs Tri-State Outputs 1OE 1O2 1O3 VCC 1O6 1O7 2O1 GND 2O4 2O5 GND 2O8 1O1 GND 1O4 1O5 GND 1O8 2O2 2O3 VCC 2O6 2O7 2OE 1 3 5 7 9 11 13 15 17 19 21 23 SSOP/TSSOP 2 4 6 8 10 12 14 16 18 20 22 24 48 46 44 42 40 38 36 34 32 30 28 26 47 45 43 41 39 37 35 33 31 29 27 25 1D1 GND 1D4 1D5 GND 1D8 2D2 2D3 VCC 2D6 2D7 2LE 1LE 1D2 1D3 VCC 1D6 1D7 2D1 GND 2D4 2D5 GND 2D8 Top View 0756B 5-15 Function Table(1) Inputs xDχ H L X Note: 1. X = Don’t Care, Z = High Impedance Outputs xOE L L H xOχ H L Z xLE H H X Absolute Maximum Ratings* Operating Temperature........................ 0°C to +70°C Storage Temperature...................... -65°C to +150°C Voltage on any Pin with Respect to Ground .................. -2.0V to +7.0V(1) Maximum Operating Voltage ............................. 6.0V *NOTICE: Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. Notes: 1. Minimum voltage is -0.6V dc which may undershoot to -2.0V for pulses of less than 20 ns. Maximum output pin voltage is VCC +0.75V dc which may overshoot to +7.0V for pulses of less than 20 ns. 5.0 Volt DC Characteristics Applicable over recommended operating range from Ta = 0°C to +70°C, VCC = +5.0V +/- 5% (unless otherwise noted) Units Symbol ∆ ICC V IH VIL IIH IIL IOZ V OH(1) Parameter Quiescent Power Supply Current Input High Voltage Input Low Voltage Input High Current Input Low Current Output Leakage Current Output High Voltage F Grade only Output High Voltage G Grade only Output Low Voltage (F Grade) Output Low Voltage (G Grade) VCC = 4.75V IOH = -10 mA VCC = 4.75V IOH = -12 mA IOL = 10 mA IOL = 12 mA 2.7 2.7 0.55 0.55 VIN = VCC VIN = GND Test Conditions VCC = Max, VIN = 3.4V 2.0 0.8 ±15 ±15 ±10 Min Typ 0.8 Max 1.2 mA V V µA µA µA V V V V V OH(2) VOL VOL Note: 1. F grade: At VCC (max), the value of VOH(max) = 3.75V and at VCC(min), VOH(max) = 3.25V 2. G grade: At VCC (max), the value of VOH(max) = 3.75V and at VCC(min), VOH(max) = 3.35V 5-16 AT16373 AT16373 AC Characteristics AT16373F Applicable over recommended operating range from Ta = 0°C to +70°C, VCC = 5.0V +/- 5% (unless otherwise noted) Symbol tPHL tPLH tPHL tPLH tPZH tPZL tPHZ tPLZ tSK(2) ∆tPHL(2) ∆ tPLH tsu tH Parameter Propagation Delay xDχ to xOχ Propagation Delay xLE to xOχ Output Enable Output Disable Output Skew Propagation Delay vs Output Loading Set-up Time Hold Time CL = 50 pF CL = 50 pF 2.0 2.0 Test Conditions(1) CL = 50 pF CL = 50 pF CL = 50 pF CL = 50 pF CL = 50 pF 1.3 Min Typ Max 2.5 5.5 8.8 6.5 0.5 1.5 Units ns ns ns ns ns ns/100 pF ns ns Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not 100% tested. AT16373G Applicable over recommended operating range from Ta = 0°C to +70°C, VCC = 5.0V +/- 5% (unless otherwise noted) Symbol tPHL tPLH tPHL tPLH tPZH tPZL tPHZ tPLZ tSK(2) ∆tPHL(2) ∆tPLH tsu tH Parameter Propagation Delay xDχ to xOχ Propagation Delay xLE to xOχ Output Enable Output Disable Output Skew Propagation Delay vs Output Loading Set-up Time Hold Time CL = 50 pF CL = 50 pF 2.0 2.0 Test Conditions(1) CL = 50 pF CL = 50 pF CL = 50 pF CL = 50 pF CL = 50 pF 0.9 Min Typ Max 2.0 5.0 8.8 Units ns ns ns ns ns ns/100 pF ns ns 6.0 0.5 1.1 Note: 1. See test circuit and waveforms. 2. This parameter is guaranteed but not 100% tested. 5-17 Test Circuits(1,2) VCC 7.0V Switch Position Test Open Drain Disable Low Enable Low All Other Tests 50 pF 500Ω Switch Closed Open VIN Pulse Generator RT D.U.T. VOUT 500Ω CL Definitions: CL = Load capacitance; Includes jig and .


AT16373F AT16373G AT16646F


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)