ISDN Equipment. HV9605 Datasheet

HV9605 Equipment. Datasheet pdf. Equivalent

Part HV9605
Description High Voltage Current Mode PWM Controller for ISDN Equipment
Feature HV9605 HV9605 Preliminary High Voltage Current Mode PWM Controller for ISDN Equipment Ordering Inf.
Manufacture Supertex Inc
Datasheet
Download HV9605 Datasheet




HV9605
HV9605
High Voltage Current Mode PWM
Controller for ISDN Equipment
Ordering Information
+VIN
Min Max
15V 250V
Feedback
Accuracy
< ± 1%
Max
Duty Cycle
49%
14 Pin
Plastic DIP
HV9605P
Package Options
14 Pin
Narrow Body SOIC
HV9605NG
Die
HV9605X
HV9605
Preliminary
Features
BiCMOS/DMOS technology
Current mode control
49% duty cycle operation
Programmable START/STOP capability
15V to 250V input range internal start-up regulator
6.0µA standby supply current for +VIN <20V
0.9mA operating supply current
5.0V VDD supply operation
30KHz to 300KHz internal oscillator
15KHz to 150KHz converter output frequency
1.0MHz low offset error amplifier
1.20V 2% band gap reference
Output driver optimized for under 10W applications
Low driver output impedance with VDD = 0V
Fast (90nsec) over current shutdown
All pins are ESD protected
General Description
The Supertex HV9605 is a BiCMOS/DMOS single-output,
current mode, pulse width modulator IC designed to meet
the requirements of ETR-060 for ISDN applications. In a 14
pin package, it provides all the necessary functions to imple-
ment a single-switch PWM with a minimum of external parts.
Utilizing Supertex’s proprietary BiCMOS/DMOS technology,
it requires less than one tenth of the operating power of
conventional bipolar PWM ICs. Dynamic range for regulation
is also increased to approximately 8 times that of similar
bipolar parts. It operates directly from any DC input voltage
between 15 and 250 VDC. The START and STOP input
voltage thresholds can be programmed within the operating
input voltage range by means of a resistor divider, provided
+VIN(START) > +VIN(STOP). The output stage is push-pull CMOS,
eliminating the need for external clamping diodes. The clock
frequency is set with a single external resistor.
Applications
ISDN network terminations
ISDN terminals
ISDN terminal adapters
Feature phones
SLIC circuits
PBX systems
Modems
Distributed power systems
DC/DC converters
Absolute Maximum Ratings*
+VIN, Input Voltage
-0.5V to +250V
Supply Voltage, VDD
Operating Temperature Range
-0.5V to +10V
-40°C to +85°C
Storage Temperature Range
-65°C to +150°C
Power Dissipation @ 25°C, SOIC
750mW
Power Dissipation @ 25°C, Plastic DIP
*All voltages referenced to GND
1000mW
11/30/98
Supertex Inc. does not recommend the use of its products in life support applications and will not knowingly sell its products for use in such applications unless it receives an adequate "products liability
indemnification insurance agreement." Supertex does not assume responsibility for use of devices described and limits its liability to the replacement of devices determined to be defective due to
workmanship. No responsibility is assumed for possible omissions or inaccuracies. Circuitry and specifications are subject to change without notice. For complete liability information11co/3ve0r/i9n8g
this and other Supertex products, refer to the Supertex 1998 Databook.
1



HV9605
Electrical Characteristics
Symbol
Parameters
Pre-Regulator/Start-Up
+VIN
+IIN
+IIN
+ISTART
Regulator input voltage
Input leakage current
Input leakage current
Pre-regulator start-up current
VDD
UVLO
HYST
Regulator output voltage
Under voltage lockout threshold
Under voltage hysteresis
Supply
VDD
IDD
Operating range
Supply current
Start/Stop Control
VSTART
ISTART
ISTOP
VCLAMP
Start threshold
Start input current
Stop input current
Zener clamp voltage on STOP Pin
MOSFET Driver Output
VOUT(HIGH)
VOUT(LOW)
tR
tF
Output high voltage
Output low voltage
Rise time
Fall time
Oscillator
fOUT Output converter frequency
TC Temperature coefficient
f/f Voltage stability
Min Typ Max Unit Conditions
HV9605
15 250 V
6.0 µA +VIN=20V, Start=0V, Stop=0V
50 µA +VIN = 250V, VDD = 4.7V
5.0 mA +VIN = 15V,
Start & Stop 10Mto + VIN
4.4 4.5 4.6 V
4.1 4.2 4.4 V VDD rising
0.1 0.3 0.4 V
4.7 8.0 V
0.9 1.3 mA OUT open,
fOUT = 20KHz to 150KHz,
VDD = 5V
6.72
20
7.30
7.88
0.05
0.05
V
µA +VIN = 18V
µA +VIN = 18V
V
4.85
4.90
0.05
30
20
0.15
50
50
V
V
nsec
nsec
IOUT = 10mA, VDD = 5.00V
IOUT = -10mA
CL = 250pf
CL = 250pf
150 KHz RT = 91K
45 50 55 KHz RT = 390K
31.5 35 38.5 KHz RT = 560K
18 20 22 KHz RT = 1.0M
100 300 PPM/°C fOUT = 50KHz
1 3 % fOUT = 50KHz, 4.5V< VDD<5.5V
11/30/98
2







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)