DatasheetsPDF.com

HS1-302RH-T Dataheets PDF



Part Number HS1-302RH-T
Manufacturers Intersil Corporation
Logo Intersil Corporation
Description Radiation Hardened CMOS Dual DPST Analog Switch
Datasheet HS1-302RH-T DatasheetHS1-302RH-T Datasheet (PDF)

HS-302RH-T Data Sheet July 1999 File Number 4603.1 Radiation Hardened CMOS Dual DPST Analog Switch Intersil’s Satellite Applications FlowTM (SAF) devices are fully tested and guaranteed to 100kRAD Total Dose. These QML Class T devices are processed to a standard flow intended to meet the cost and shorter lead-time needs of large volume satellite manufacturers, while maintaining a high level of reliability. The HS-302RH-T analog switch is a monolithic device fabricated using Radiation Hardened CM.

  HS1-302RH-T   HS1-302RH-T



Document
HS-302RH-T Data Sheet July 1999 File Number 4603.1 Radiation Hardened CMOS Dual DPST Analog Switch Intersil’s Satellite Applications FlowTM (SAF) devices are fully tested and guaranteed to 100kRAD Total Dose. These QML Class T devices are processed to a standard flow intended to meet the cost and shorter lead-time needs of large volume satellite manufacturers, while maintaining a high level of reliability. The HS-302RH-T analog switch is a monolithic device fabricated using Radiation Hardened CMOS technology and the Intersil dielectric isolation process for latch-up free operation. Improved total dose hardness is obtained by layout (thin oxide tabs extending to a channel stop) and processing (hardened gate oxide). These switches offer lowresistance switching performance for analog voltages up to the supply rails. “ON” resistance is low and stays reasonably constant over the full range of operating voltage and current. “ON” resistance also stays reasonably constant when exposed to radiation, being typically 30Ω pre-rad and 35Ω post 100kRAD(Si). This device provide break-before-make switching. Features • QML Class T, Per MIL-PRF-38535 • Radiation Performance - Gamma Dose (γ) 1 x 105 RAD(Si) • No Latch-Up, Dielectrically Isolated Device Islands • Pin for Pin Compatible with Intersil HI-302 Series Analog Switches • Analog Signal Range 15V • Low Leakage . . . . . . . . . . . . . . . . 100nA (Max, Post Rad) • Low RON . . . . . . . . . . . . . . . . . . . . . 60Ω (Max, Post Rad) • Low Operating Power . . . . . . . . . . 100µA (Max, Post Rad) Pinouts HS1-302RH-T (SBDIP), CDIP2-T14 TOP VIEW NC 1 S3 2 D3 3 D1 4 S1 5 IN1 6 GND 7 14 V+ 13 S4 12 D4 11 D2 10 S2 9 IN2 8 V- Specifications Specifications for Rad Hard QML devices are controlled by the Defense Supply Center in Columbus (DSCC). The SMD numbers listed below must be used when ordering. Detailed Electrical Specifications for the HS-302RH-T are contained in SMD 5962-95812. A “hot-link” is provided from our website for downloading. www.intersil.com/spacedefense/newsafclasst.asp Intersil’s Quality Management Plan (QM Plan), listing all Class T screening operations, is also available on our website. www.intersil.com/spacedefense/newsafclasst.asp HS9-302RH-T (FLATPACK), CDFP3-F14 TOP VIEW 1 NC S3 D3 D1 S1 IN1 GND 2 3 4 5 6 7 14 13 12 11 10 9 8 V+ S4 D4 D2 S2 IN2 V- Ordering Information ORDERING NUMBER 5962R9581201TCC 5962R9581201TXC PART NUMBER HS1-302RH-T HS9-302RH-T TEMP. RANGE (oC) -55 to 125 -55 to 125 Functional Diagram N P D IN NOTE: Minimum order quantity for -T is 150 units through distribution, or 450 units direct. TRUTH TABLE LOGIC 0 1 ALL SWITCHES OFF ON 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999 Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation. HS-302RH-T Die Characteristics DIE DIMENSIONS: (2130µm x 1930µm x 279µm ±25.4µm) 84 x 7.


HS1-302RH HS1-302RH-T HS1-302RH883S


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)