Analog Switch. HS1-390RH-T Datasheet
July 1999 File Number 4604.1
CMOS Dual SPDT Analog Switch
Intersil’s Satellite Applications FlowTM (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. This QML
Class T device is processed to a standard ﬂow intended to
meet the cost and shorter lead-time needs of large volume
satellite manufacturers, while maintaining a high level of
The HS-390RH-T analog switch is a monolithic device
fabricated using Radiation Hardened CMOS technology and
the Intersil dielectric isolation process for latch-up free
operation. Improved total dose hardness is obtained by
layout (thin oxide tabs extending to a channel stop) and
processing (hardened gate oxide). These switches offer low-
resistance switching performance for analog voltages up to
the supply rails. “ON” resistance is low and stays reasonably
constant over the full range of operating voltage and current.
“ON” resistance also stays reasonably constant when
exposed to radiation, being typically 30Ω pre-rad and 35Ω
post 100kRAD(Si). Break-before-make switching is
controlled by 5V digital inputs.
Speciﬁcations for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Speciﬁcations for the HS-390RH-T
are contained in SMD 5962-95813. A “hot-link” is provided
from our website for downloading.
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
-55 to 125
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 105 RAD(Si)
- No Latch-Up, Dielectrically Isolated Device Islands
• Pin for Pin Compatible with Intersil HI-390 Series Analog
• Analog Signal Range 15V
• Low Leakage . . . . . . . . . . . . . . . . 100nA (Max, Post Rad)
• Low rON . . . . . . . . . . . . . . . . . . . . . . 60Ω (Max, Post Rad)
• Low Operating Power . . . . . . . . . . 100µA (Max, Post Rad)
HS1-390RH (SBDIP), CDIP2-T16
HS9-390RH (FLATPACK), CDFP4-F16
IN N P
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.
(2130µm x 1930µm x 279µm ±25.4µm)
84 x 76 x 11mils ±1mil
Thickness: 12.5kÅ ±2kÅ
Metallization Mask Layout
Type: Silox (SiO2)
Thickness: 8.0kÅ ±1.0kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
Metal Gate CMOS, Dielectric Isolation
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certiﬁcation.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Ofﬁce Headquarters
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
Intersil (Taiwan) Ltd.
7F-6, No. 101 Fu Hsing North Road
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029