Analog Switch. HS9-390RH-T Datasheet

HS9-390RH-T Switch. Datasheet pdf. Equivalent

Part HS9-390RH-T
Description Radiation Hardened CMOS Dual SPDT Analog Switch
Feature HS-390RH-T Data Sheet July 1999 File Number 4604.1 Radiation Hardened CMOS Dual SPDT Analog Switch .
Manufacture Intersil Corporation
Datasheet
Download HS9-390RH-T Datasheet




HS9-390RH-T
Data Sheet
HS-390RH-T
July 1999 File Number 4604.1
Radiation Hardened
CMOS Dual SPDT Analog Switch
Intersil’s Satellite Applications FlowTM (SAF) devices are fully
tested and guaranteed to 100kRAD total dose. This QML
Class T device is processed to a standard flow intended to
meet the cost and shorter lead-time needs of large volume
satellite manufacturers, while maintaining a high level of
reliability.
The HS-390RH-T analog switch is a monolithic device
fabricated using Radiation Hardened CMOS technology and
the Intersil dielectric isolation process for latch-up free
operation. Improved total dose hardness is obtained by
layout (thin oxide tabs extending to a channel stop) and
processing (hardened gate oxide). These switches offer low-
resistance switching performance for analog voltages up to
the supply rails. “ON” resistance is low and stays reasonably
constant over the full range of operating voltage and current.
“ON” resistance also stays reasonably constant when
exposed to radiation, being typically 30pre-rad and 35
post 100kRAD(Si). Break-before-make switching is
controlled by 5V digital inputs.
Specifications
Specifications for Rad Hard QML devices are controlled by
the Defense Supply Center in Columbus (DSCC). The SMD
numbers listed below must be used when ordering.
Detailed Electrical Specifications for the HS-390RH-T
are contained in SMD 5962-95813. A “hot-link” is provided
from our website for downloading.
www.intersil.com/spacedefense/newsafclasst.asp
Intersil’s Quality Management Plan (QM Plan), listing all
Class T screening operations, is also available on our
website.
www.intersil.com/quality/manuals.asp
Ordering Information
ORDERING
NUMBER
PART
NUMBER
TEMP.
RANGE
(oC)
5962R9581303TEC
HS1-390RH-T
-55 to 125
5962R9581303TYC
HS9-390RH-T
-55 to 125
NOTE: Minimum order quantity for -T is 150 units through
distribution, or 450 units direct.
Features
• QML Class T, Per MIL-PRF-38535
• Radiation Performance
- Gamma Dose (γ) 1 x 105 RAD(Si)
- No Latch-Up, Dielectrically Isolated Device Islands
• Pin for Pin Compatible with Intersil HI-390 Series Analog
Switches
• Analog Signal Range 15V
• Low Leakage . . . . . . . . . . . . . . . . 100nA (Max, Post Rad)
• Low rON . . . . . . . . . . . . . . . . . . . . . . 60(Max, Post Rad)
• Low Operating Power . . . . . . . . . . 100µA (Max, Post Rad)
Pinouts
HS1-390RH (SBDIP), CDIP2-T16
TOP VIEW
D1 1
NC 2
D3 3
S3 4
S4 5
D4 6
NC 7
D2 8
16 S1
15 IN1
14 V-
13 GND
12 NC
11 V+
10 IN2
9 S2
HS9-390RH (FLATPACK), CDFP4-F16
TOP VIEW
1
D1
2
NC
3
D3
4
S3
5
S4
6
D4
7
NC
8
D2
16
S1
15
IN1
14
V-
13
GND
12
NC
11
V+
10
IN2
9
S2
Functional Diagram
IN N P
D
LOGIC
0
1
TRUTH TABLE
SW1 SW2
OFF
ON
SW3 SW4
ON
OFF
1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
www.intersil.com or 407-727-9207 | Copyright © Intersil Corporation 1999
Satellite Applications Flow™ (SAF) is a trademark of Intersil Corporation.



HS9-390RH-T
Die Characteristics
DIE DIMENSIONS:
(2130µm x 1930µm x 279µm ±25.4µm)
84 x 76 x 11mils ±1mil
METALLIZATION:
Type: Al
Thickness: 12.5kÅ ±2kÅ
SUBSTRATE POTENTIAL:
Unbiased (DI)
BACKSIDE FINISH:
Gold
Metallization Mask Layout
HS-390RH-T
PASSIVATION:
Type: Silox (SiO2)
Thickness: 8.0kÅ ±1.0kÅ
WORST CASE CURRENT DENSITY:
< 2.0e5 A/cm2
TRANSISTOR COUNT:
76
PROCESS:
Metal Gate CMOS, Dielectric Isolation
HS-390RH-T
S3 V-
GND
S4
V+
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site http://www.intersil.com
Sales Office Headquarters
NORTH AMERICA
Intersil Corporation
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (407) 724-7000
FAX: (407) 724-7240
EUROPE
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
ASIA
Intersil (Taiwan) Ltd.
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
2







@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)