DatasheetsPDF.com

AV9110-02CS14 Dataheets PDF



Part Number AV9110-02CS14
Manufacturers Integrated Circuit Systems
Logo Integrated Circuit Systems
Description Serially Programmable Frequency Generator
Datasheet AV9110-02CS14 DatasheetAV9110-02CS14 Datasheet (PDF)

Integrated Circuit Systems, Inc. AV9110 Serially Programmable Frequency Generator General Description The AV9110 generates user specified clock frequencies using an externally generated input reference, such as 14.318 MHz or 10.00 MHz crystal connected between pins 1 and 14. Alternately, a TTL input reference clock signal can be used. The output frequency is determined by a 24-bit digital word entered through the serial port. The serial port enables the user to change the output frequency on-t.

  AV9110-02CS14   AV9110-02CS14



Document
Integrated Circuit Systems, Inc. AV9110 Serially Programmable Frequency Generator General Description The AV9110 generates user specified clock frequencies using an externally generated input reference, such as 14.318 MHz or 10.00 MHz crystal connected between pins 1 and 14. Alternately, a TTL input reference clock signal can be used. The output frequency is determined by a 24-bit digital word entered through the serial port. The serial port enables the user to change the output frequency on-the-fly. The clock outputs utilize CMOS level output buffers that operate up to 130 MHz. Features • • • • • • • • • Complete user programmability of output frequency through serial input data port On-chip Phase-Locked Loop for clock generation Generates accurate frequencies up to 130 MHz Tristate CMOS outputs 5 volt power supply Low power CMOS technology 14-pin DIP or 150-mil SOIC Very low jitter Wide operating range VCO Applications Graphics: The AV9110 generates low jitter, high speed pixel (or dot) clocks. It can be used to replace multiple expensive high speed crystal oscillators. The flexibility of this device allows it to generate nonstandard graphics clocks, allowing the user to program frequencies on-the-fly. Block Diagram 9110 Rev F 5/30/00 ICS reserves the right to make changes in the device data identified in this publication without further notice. ICS advises its customers to obtain the latest version of all device data to verify that any information being relied upon by the customer is current and accurate. AV9110 Pin Configuration Clock Reference Implementations: AV9110-01 vs. AV9110-02 The AV9110 requires a stable reference clock (5 to 32 MHz) to generate a stable, low jitter output clock. The AV9 11 0 -01 is optimized to use an external quartz crystal as a frequency reference, without the need of additional external components. The AV9110-02 is optimized to accept an TTL clock reference. Either device can be used with an external crystal or accept a TTL clock reference, although extra components may be required. The various combinations implied are summarized in Figure 2 (see page 7). 14 Pin Dip, SOIC Pin Descriptions PIN NUMBER 1 2 3 4 5 6 7 8 9 10 11 12 13 14 P I N NA M E X1 AV D D AGND VDD GND DATA SCLK CE# CLK/X GND VDD CLK OE X2 PIN TYPE Input P ow e r P ow e r P ow e r P ow e r Input Input Input Output P ow e r Power Output Input Output DESCRIPTION Crystal input or TTL reference clock. ANALOG power supply. Connect to +5V. ANALOG GROUND. Digital power supply. Connect to +5V. Digital GROUND. Serial DATA pin. SERIAL CLOCK. Clocks shift register. CHIP ENABLE. Active low, controls data transfer. CMOS CLOCK divided by X output. Digital GROUND. Digital power supply. Connect to +5V. CMOS CLOCK output. OUTPUT ENABLE. Tristates both outputs when low. Crystal input or TTL reference clock. 2 AV9110 Absolute Maximum Ratings Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . 7.0 V Voltage on I/O pins referenced to GND . . . . . . GND –0.5 V to VDD +0.5 V Operating Temperature under bias . . . . . . . . . . 0°C to +70°C Power dissipation . . . . . . . . . . . . . . . . . . . . . . . . 0.8 Watts Storage Temperature . . . . . . . . . . . . . . . . . . . . . . –65°C to +150°C Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. These ratings are stress specifications only and functional operation of the device at these or any other conditions above those listed in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect product reliability. Electrical Characteristics VDD = +5V±10%, TA = 0 – 70° C unless otherwise stated DC/STATIC PARAMETER Input Low Voltage Input High Voltage Input Low Current Input High Current Output Low Voltage 1 1 1 SYMBOL VIL VIH IIL IIH VOL VOH IOH = 8Ma ICLKr ICLKf IDD fo tr tf dt TEST CONDITIONS VDD = 5V VDD = 5V VIN = OV VIN = VDD IOL = 8Ma MIN 2.0 2.4 - TYP 25 MAX 0.8 -5 5 0.4 20 20 - UNITS V V µA µA V V ns ns mA Output High Voltage Input Clock Rise Time Input Clock Fall Time Supply Current 1 No load AC/DYNAMIC - Output frequency range Rise time, 20-80% Fall time, 80-20% 1 1 0.78 25pF load 25pF load 25pF load 40 - ±40 ±125 14.318 14.318 400 130 3 3 60 32 32 32 - MHz ns ns % ps ps MHz MHz MHz ps 1 Duty cycle @ 50% Jitter, 1 sigma 1 1 1 1 Jitter, absolute Input reference freq.; AV9110-01 fREF fREF fDATA tskew Crystal input TTL input 5 0.6 - Input reference freq.; AV9110-02 Input DATA or SCLK frequency Skew, Output to Output/X1 1 Note 1: Parameter is guaranteed by design and characterization. Not 100% tested in production. 3 AV9110 Serial Programming The AV9110 is programmed to generate clock frequencies by entering data through the shift register. Figure 1 displays the proper timing sequence. On the negative going edge of CE#, the shift register is enabled and the data at the DATA pin is loaded into th.


AV9110-02CN14 AV9110-02CS14 AV9154A


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)