DatasheetsPDF.com

HY29F002TC-70 Dataheets PDF



Part Number HY29F002TC-70
Manufacturers Hynix Semiconductor
Logo Hynix Semiconductor
Description 2 Megabit (256K x 8)/ 5 Volt-only/ Flash Memory
Datasheet HY29F002TC-70 DatasheetHY29F002TC-70 Datasheet (PDF)

HY29F002T 2 Megabit (256K x 8), 5 Volt-only, Flash Memory KEY FEATURES n 5 Volt Read, Program, and Erase – Minimizes system-level power requirements n High Performance – Access times as fast as 45 ns n Low Power Consumption – 20 mA typical active read current – 30 mA typical program/erase current – 1 µA typical CMOS standby current n Compatible with JEDEC Standards – Package, pinout and command-set compatible with the single-supply Flash device standard – Provides superior inadvertent write prot.

  HY29F002TC-70   HY29F002TC-70



Document
HY29F002T 2 Megabit (256K x 8), 5 Volt-only, Flash Memory KEY FEATURES n 5 Volt Read, Program, and Erase – Minimizes system-level power requirements n High Performance – Access times as fast as 45 ns n Low Power Consumption – 20 mA typical active read current – 30 mA typical program/erase current – 1 µA typical CMOS standby current n Compatible with JEDEC Standards – Package, pinout and command-set compatible with the single-supply Flash device standard – Provides superior inadvertent write protection n Sector Erase Architecture – Boot sector architecture with top boot block location – One 16 Kbyte, two 8 Kbyte, one 32 Kbyte and three 64K byte sectors – A command can erase any combination of sectors – Supports full chip erase n Erase Suspend/Resume – Temporarily suspends a sector erase operation to allow data to be read from, or programmed into, any sector not being erased GENERAL DESCRIPTION The HY29F002T is an 2 Megabit, 5 volt-only CMOS Flash memory organized as 262,144 (256K) bytes. The device is offered in industrystandard 32-pin TSOP and PLCC packages. The HY29F002T can be programmed and erased in-system with a single 5-volt VCC supply. Internally generated and regulated voltages are provided for program and erase operations, so that the device does not require a high voltage power supply to perform those functions. The device can also be programmed in standard EPROM programmers. Access times as fast as 55ns over the full operating voltage range of 5.0 volts ± 10% are offered for timing compatibility with the zero wait state requirements of high speed microprocessors. A 45ns version operating over 5.0 volts ± 5% is also available. To eliminate bus contention, the 18 A[17:0] RESET# CE# OE# WE# DQ[7:0] 8 n Sector Protection – Any combination of sectors may be locked to prevent program or erase operations within those sectors n Temporary Sector Unprotect – Allows changes in locked sectors (requires high voltage on RESET# pin) n Internal Erase Algorithm – Automatically erases a sector, any combination of sectors, or the entire chip n Internal Programming Algorithm – Automatically programs and verifies data at a specified address n Fast Program and Erase Times – Byte programming time: 7 µs typical – Sector erase time: 1.0 sec typical – Chip erase time: 7 sec typical n Data# Polling and Toggle Status Bits – Provide software confirmation of completion of program or erase operations n Minimum 100,000 Program/Erase Cycles n Space Efficient Packaging – Available in industry-standard 32-pin TSOP and PLCC packages LOGIC DIAGRAM Revision 4.1, May 2001 HY29F002T HY29F002T has separate chip enable (CE#), write enable (WE#) and output enable (OE#) controls. The device is compatible with the JEDEC single power-supply Flash command set standard. Commands are written to the command register using standard microprocessor write timings, from where they are routed to an internal state-machine that controls the erase and programming circuits. Device programmi.


HY29F002TC-55 HY29F002TC-70 HY29F002TC-90


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)