DatasheetsPDF.com

X24321 Dataheets PDF



Part Number X24321
Manufacturers Xicor
Logo Xicor
Description 400 KHz 2-Wire Serial E2PROM
Datasheet X24321 DatasheetX24321 Datasheet (PDF)

32K X24321 400 KHz 2-Wire Serial E2PROM 4K x 8 Bit FEATURES • • • • • • • • • • 1.8V to 3.6V, 2.5V to 5.5V and 4.5V to 5.5V Power Supply Operation Low Power CMOS —Active Read Current Less Than 1mA —Active Write Current Less Than 3mA —Standby Current Less Than 1µA 400KHz Fast Mode 2-Wire Serial Interface —Down to 1.8V —Schmitt Trigger Input Noise Suppression —Output Slope Control for Ground Bounce Noise Elimination Internally Organized 4K x 8 Bit 32 Byte Page Write Mode —Minimizes Total Wr.

  X24321   X24321



Document
32K X24321 400 KHz 2-Wire Serial E2PROM 4K x 8 Bit FEATURES • • • • • • • • • • 1.8V to 3.6V, 2.5V to 5.5V and 4.5V to 5.5V Power Supply Operation Low Power CMOS —Active Read Current Less Than 1mA —Active Write Current Less Than 3mA —Standby Current Less Than 1µA 400KHz Fast Mode 2-Wire Serial Interface —Down to 1.8V —Schmitt Trigger Input Noise Suppression —Output Slope Control for Ground Bounce Noise Elimination Internally Organized 4K x 8 Bit 32 Byte Page Write Mode —Minimizes Total Write Time Per Byte Hardware Write Protect Bidirectional Data Transfer Protocol Self-Timed Write Cycle —Typical Write Cycle Time of 5ms High Reliability —Endurance: 1,000,000 Cycles —Data Retention: 100 Years 8-Lead SOIC DESCRIPTION The X24321 is a CMOS Serial E2PROM Memory, internally organized 4K x 8. The device features a serial interface and software protocol allowing operation on a simple two wire bus. The bus operates at 400KHz all the way down to 1.8V. Three device select inputs (S0–S2) allow up to eight devices to share a common two wire bus. Hardware Write Protection is provided through a Write Protect (WP) input pin on the X24321. When the WP pin is HIGH, the upper quadrant of the Serial E2PROM array is protected against any nonvolatile write attempts. Xicor Serial E2PROM Memories are designed and tested for applications requiring extended endurance. Inherent data retention is greater than 100 years. FUNCTIONAL DIAGRAM SERIAL E2PROM DATA AND ADDRESS (SDA) DATA REGISTER Y DECODE LOGIC COMMAND DECODE AND CONTROL LOGIC SCL PAGE DECODE LOGIC S2 S1 S0 DEVICE SELECT LOGIC WRITE PROTECT LOGIC E2PROM ARRAY 4K x 8 WP WRITE VOLTAGE CONTROL 7040 FM 01 ©Xicor, 1995, 1996 Patents Pending 7040 3/27/97 T0/C0/D0 SH 1 Characteristics subject to change without notice X24321 PIN DESCRIPTIONS Serial Clock (SCL) The SCL input is used to clock all data into and out of the device. Serial Data (SDA) SDA is a bidirectional pin used to transfer data into and out of the device. It is an open drain output and may be wire-ORed with any number of open drain or open collector outputs. An open drain output requires the use of a pull-up resistor. For selecting typical values, refer to the Pullup resistor selection graph at the end of this data sheet. Device Select (S0, S1, S2) The device select inputs (S0, S1, S2) are used to set the first three bits of the 8-bit slave address. This allows up to eight devices to share a common bus. These inputs can be static or actively driven. If used statically they must be tied to VSS or VCC as appropriate. If actively driven, they must be driven with CMOS levels. Write Protect (WP) The Write Protect input controls the Hardware Write Protect feature. When held LOW, Hardware Write Protection is disabled and the device can be written normally. When this input is held HIGH, Write Protection is enabled, and nonvolatile writes are disabled to the upper quadrant of the E2PROM array. PIN NAMES Symbol S0, S1, S2 SDA SCL WP VSS VCC Descrip.


X24320 X24321 X24325


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)