DatasheetsPDF.com

TSOP1836YA1 Dataheets PDF



Part Number TSOP1836YA1
Manufacturers Vishay Telefunken
Logo Vishay Telefunken
Description Photo Modules
Datasheet TSOP1836YA1 DatasheetTSOP1836YA1 Datasheet (PDF)

TSOP18..YA1 Vishay Telefunken Photo Modules for PCM Remote Control Systems Available types for different carrier frequencies Type TSOP1830YA1 TSOP1836YA1 TSOP1838YA1 TSOP1856YA1 fo 30 kHz 36 kHz 38 kHz 56 kHz Type TSOP1833YA1 TSOP1837YA1 TSOP1840YA1 fo 33 kHz 36.7 kHz 40 kHz Description The TSOP18..YA1 – series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated outpu.

  TSOP1836YA1   TSOP1836YA1


Document
TSOP18..YA1 Vishay Telefunken Photo Modules for PCM Remote Control Systems Available types for different carrier frequencies Type TSOP1830YA1 TSOP1836YA1 TSOP1838YA1 TSOP1856YA1 fo 30 kHz 36 kHz 38 kHz 56 kHz Type TSOP1833YA1 TSOP1837YA1 TSOP1840YA1 fo 33 kHz 36.7 kHz 40 kHz Description The TSOP18..YA1 – series are miniaturized receivers for infrared remote control systems. PIN diode and preamplifier are assembled on lead frame, the epoxy package is designed as IR filter. The demodulated output signal can directly be decoded by a microprocessor. The main benefit is the reliable function even in disturbed ambient and the protection against uncontrolled output pulses. 16 083 Features D D D D D Photo detector and preamplifier in one package Internal filter for PCM frequency TTL and CMOS compatibility Output active low Improved shielding against electrical field disturbance Special Features D Small size package D Enhanced immunity against all kinds of disturbance light D No occurrence of disturbance pulses at the D Short settling time after power on (<200ms) output D Suitable burst length ≥6 cycles/burst Block Diagram 3 Input Control Circuit 30 kW 1 PIN AGC Band Pass Demodulator 2 9612226 VS OUT GND Document Number 82057 Rev. 4, 08-Jun-00 www.vishay.de • FaxBack +1-408-970-5600 1 (7) TSOP18..YA1 Vishay Telefunken Absolute Maximum Ratings Tamb = 25_C Parameter Supply Voltage Supply Current Output Voltage Output Current Junction Temperature Storage Temperature Range Operating Temperature Range Power Consumption Soldering Temperature Test Conditions (Pin 3) (Pin 3) (Pin 1) (Pin 1) Symbol VS IS VO IO Tj Tstg Tamb Ptot Tsd Value –0.3...6.0 5 –0.3...6.0 5 100 –25...+85 –25...+85 50 260 Unit V mA V mA °C °C °C mW °C (Tamb 85 °C) t 10 s, 1 mm from case x x Basic Characteristics Tamb = 25_C Parameter Supply y Current ( (Pin 3) ) Supply Voltage (Pin 3) Transmission Distance Output Voltage Low (Pin 1) Irradiance (30 – 40 kHz) Irradiance (56 kHz) Irradiance Directivity Test Conditions VS = 5 V, Ev = 0 VS = 5 V, Ev = 40 klx, sunlight Ev = 0, test signal see fig.6, IR diode TSAL6200, IF = 300 mA IOSL = 0.5 mA,Ee = 0.7 mW/m2, f = fo Pulse width tolerance: tpi – 4/fo < tpo < tpi + 6/fo, test signal see fig.6 Angle of half transmission distance Symbol ISD ISH VS d VOSL Ee min Ee min Ee max ϕ1/2 30 ±45 0.3 0.4 Min 0.9 4.5 35 250 0.5 0.7 Typ 1.2 1.3 Max 1.5 5.5 Unit mA mA V m mV mW/m2 mW/m2 W/m2 deg Application Circuit 100 W *) >10 k +5V 3 TSOP18.. TSAL62.. 4.7 F *) m optional 1 W mC 2 GND 15905 *) recommended to suppress power supply disturbances www.vishay.de • FaxBack +1-408-970-5600 2 (7) Document Number 82057 Rev. 4, 08-Jun-00 TSOP18..YA1 Vishay Telefunken Suitable Data Format The circuit of the TSOP18..YA1 is designed in that way that unexpected output pulses due to noise or disturbance signals are avoided. A bandpassfilter, an integrator stage and an automatic gain control are used to suppress such disturbances. The distinguishing mark between data signal ( not suppressed) and disturbance signal (supressed) are carrier frequency, burst length and Signal Gap Time (see diagram below). The data signal should fullfill the following condition: • Carrier frequency should be close to center frequency of the bandpass (e.g. 38kHz). • Burst length should be 6 cycles/burst or longer. • After each burst a gap time of at least 9 cycles is neccessary. • The data format should not make a continuous signal transmission. There must be a Signal Gap Time (longer than 15ms) at least each 90ms (see Figure A) Some examples for suitable data format are: NEC Code (repetitive pulse), NEC Code (repetitive data), Toshiba Micom Format, Sharp Code, RC5 Code, RECS–80 Code, R–2000 Code. When a disturbance signal is applied to the TSOP18..YA1 it can still receive the data signal. However the sensitivity is reduced to that level that no unexpected pulses will occure. Some examples for such disturbance signals which are suppressed by the TSOP18..YA1 are: • DC light (e.g. from tungsten bulb or sunlight), • Continuous signal at 38kHz or at any other frequency, • Signals from fluorescent lamps (see Figure B). • Continuous IR signal (e.g. 1ms burst, 2ms pause) Signal Gap Time 0 10 20 30 40 50 time [ms] 60 70 80 90 100 Figure A: Data Signal (Output of IR Receiver) with a Signal Gap Time of 20ms Signal Gap Time 0 2 4 6 8 10 time [ms] 12 14 16 18 20 Figure B: Disturbance Signal from Fluorescent Lamp with Signal Gap Time of 7ms (suppressed by TSOP18..) Document Number 82057 Rev. 4, 08-Jun-00 www.vishay.de • FaxBack +1-408-970-5600 3 (7) TSOP18..YA1 Vishay Telefunken Typical Characteristics (Tamb = 25_C unless otherwise specified) 1.0 0.8 E e min – Threshold Irradiance (mW/m2 ) /eE – Rel. Responsitivity 100.0 f = fo 10.0 10 kHz 1 kHz 1.0 0.6 0.4 0.2 0.0 0.7 0.8 0.9 1.0 1.1 1.2 1.3 Df ( 3 dB ) = f0 / 7 f / f0 – Relative Frequency f = f0 "5% eE min 100 Hz 0.1 0.1 1.0 10.0 100.0 1000.0 94 9102 96 122.


TSOP1836XG1 TSOP1836YA1 TSOP1836ZC1


@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site.
(Privacy Policy & Contact)