TQ2H-L-5V C RELAY Datasheet

TQ2H-L-5V Datasheet, PDF, Equivalent


Part Number

TQ2H-L-5V

Description

LOW PROFILE 2 FORM C RELAY

Manufacture

ETC

Total Page 7 Pages
Datasheet
Download TQ2H-L-5V Datasheet


TQ2H-L-5V
LOW PROFILE
2 FORM C RELAY
TESTING
TQ-RELAYS
FEATURES
9
.354
• High sensitivity:
26.7
1.051
5+0.4
–0.2
.197+–..001068
14
.551
9
.354
2 Form C: 140 mW power consumption (single side stable type)
4 Form C: 280 mW power consumption (single side stable type)
5+0.4
–0.2
.197+–..001068
• Surge voltage withstand: 1500 V FCC Part 68
• Sealed construction allows automatic washing
• Self-clinching terminal also available
• M.B.B. contact types available
mm inch
SPECIFICATIONS
Contact
Standard
(B.B.M) type
M.B.B.type
Arrangement
2 Form C 4 Form C 2 Form D
Initial contact resistance, max.
(By voltage drop 6 V DC 1A)
50 m
Contact material
Gold-clad silver
Nominal switching capacity
(resistive load)
1 A 30 V DC
0.5 A 125 V AC
1 A 30 V
DC
Rating
Max. switching power
(resistive load)
Max. switching voltage
30 W, 62.5 V A
110 V DC, 125 V AC
30 W
110 V DC
Max. switching current
Min. switching capacity f1
1A
10 µA 10 mV DC
Single side stable
Nominal
operating
power 1 coil latching
140 mW
(3 to 12 V DC)
200 mW
(24 V DC)
300 mW
(48 V DC)
280 mW
(3 to 24 V DC)
400 mW
(48 V DC)
100 mW
(3 to 12 V DC)
150 mW
(24 V DC)
200 mW
200 mW
2 coil latching
200 mW
(3 to 12 V DC)
300 mW
(24 V DC)
400 mW
Expected
life (min.
opera-
tions)
Mechanical (at 180 cpm)
Electrical
(at 20 cpm)
(1 A 30 V DC
resistive)
1 A 30 V DC
resistive
0.5 A 125 V AC
resistive
108
2×105
105
107
105
Note:
f1This value can change due to the switching frequency, environmental conditions,
and desired reliability level, therefore it is recommended to check this with the ac-
tual load.
Remarks
* Specifications will vary with foreign standards certification ratings.
*1 Measurement at same location as "Initial breakdown voltage" section.
*2 By resistive method, nominal voltage applied to the coil; contact carrying current:
1 A.
*3 Nominal voltage applied to the coil, excluding contact bounce time.
*4 Nominal voltage applied to the coil, excluding contact bounce time without diode.
*5 Half-wave pulse of sine wave: 11 ms; detection time: 10 µs.
*6 Half-wave pulse of sine wave: 6 ms.
*7 Detection time: 10 µs.
Characteristics
Standard
(B.B.M) type
M.B.B.type
Initial insulation resistance*1
Min. 1,000 M(at 500 V DC)
Initial
breakdown
voltage
Between open
contacts
Between contact
and coil
750 Vrms for 1 min. 300 Vrms for 1 min.
(Detection current: (Detection current:
10 mA)
10 mA)
1,000 Vrms for 1 min.
(Detection current: 10 mA)
Between contact
sets
1,000 Vrms for 1 min.
(Detection current: 10 mA)
FCC surge voltage between open
contacts
1,500 V
Operate time [Set time]*3
(at 20°C)
Max. 3 ms (Approx. 2 ms)
[Max. 3 ms (Approx. 2 ms)]
Release time [Reset time]*4
(at 20°C)
M.B.B. time*8
Temperature rise*2 (at 20°C)
Max. 3 ms (Approx. 1 ms)
[Max. 3 ms (Approx. 2 ms)]
— Min. 10 µs.
Max. 50°C
Functional*5
Shock resistance
Destructive*6
Min. 490 m/s2 {50G}
Min. 980 m/s2 {100G}
Vibration
resistance
Functional*7
Destructive
176.4 m/s2 {18G}, 10 to 55 Hz
at double amplitude of 3 mm
294 m/s2 {30G}, 10 to 55 Hz
at double amplitude of 5 mm
Conditions for
operation, trans-
port and storage*9
(Not freezing and
condensing at low
temperature)
Ambient
temperature
Humidity
–40°C to +70°C
–40°F to +158°F
–40°C to +50°C
–40°F to +122°F
5 to 85% R.H.
Unit weight
2 Form C:
4 Form C:
Approx. 1.5 g .053 oz
Approx. 3 g .106 oz.
*8 M.B.B. time:
Measuring
condition
Min. 10 µs
500
5 V DC
*9 Refer to 4. Conditions for operation, transport and storage mentioned in Cautions
for use (Page 178).
133

TQ2H-L-5V
TQ
ORDERING INFORMATION
EX. TQ 2
H L2 2M 3V
Contact arrangement
Terninal shape
Operating function MBB function Coil voltage (DC)
2: 2 Form C
4: 4 Form C
Nil: Standard PC board Nil: Single side stable Nil: Standard
terminal
L: 1 coil latching
(B.B.M.) type
H: Self-clinching terminal L2: 2 coil latching
2M: 2M.B.B. type
3, 4.5, 5, 6, 9,
12, 24, 48* V
*48 V coil type: Single side stable only
Notes: 1. AgPd stationary contact types available for high resistance against contact sticking.
When ordering, please add suffix “–3” like TQ2-12V-3.
2. M.B.B. contact types are available only for TQ2 type.
TYPES AND COIL DATA (at 20°C 68°F)
1. Standard (B.B.M.) type
2 Form C type
1. Single side stable
Part No.
Standard PC Self-clinching
board terminal
terminal
TQ2-3 V
TQ2-4.5 V
TQ2-5 V
TQ2-6 V
TQ2-9 V
TQ2-12 V
TQ2-24 V
TQ2-48 V
TQ2H-3 V
TQ2H-4.5 V
TQ2H-5 V
TQ2H-6 V
TQ2H-9 V
TQ2H-12 V
TQ2H-24 V
TQ2H-48 V
Nominal
voltage,
V DC
3
4.5
5
6
9
12
24
48
Pick-up
voltage,
V DC (max.)
2.25
3.38
3.75
4.5
6.75
9
18
36
Drop-out
voltage,
V DC (min.)
0.3
0.45
0.5
0.6
0.9
1.2
2.4
4.8
Nominal
operating
current,
mA (±10%)
46.7
31.1
28.1
23.3
15.5
11.7
8.3
6.25
Coil
resistance,
(±10%)
64.3
144.6
178
257
579
1,028
2,880
7,680
Nominal
operating
power,
mW
140
140
140
140
140
140
200
300
Max.
allowable
voltage,
V DC
4.5
6.7
7.5
9
13.5
18
36
57.6
2. 1 Coil latching
Part No.
Standard PC Self-clinching
board terminal
terminal
TQ2-L-3 V
TQ2-L-4.5 V
TQ2-L-5 V
TQ2-L-6 V
TQ2-L-9 V
TQ2-L-12 V
TQ2-L-24 V
TQ2H-L-3 V
TQ2H-L-4.5 V
TQ2H-L-5 V
TQ2H-L-6 V
TQ2H-L-9 V
TQ2H-L-12 V
TQ2H-L-24 V
Nominal
voltage,
V DC
3
4.5
5
6
9
12
24
Set voltage, Reset voltage,
V DC (max.) V DC (min.)
2.25 2.25
3.38 3.38
3.75 3.75
4.5 4.5
6.75 6.75
99
18 18
Nominal
operating
current,
mA (±10%)
33.3
22.2
20
16.7
11.1
8.3
6.3
Coil
resistance,
(±10%)
90
202.5
250
360
810
1,440
3,840
Nominal
operating
power,
mW
100
100
100
100
100
100
150
Max.
allowable
voltage,
V DC
4.5
6.7
7.5
9
13.5
18
36
3. 2 Coil latching
Part No.
Standard PC Self-clinching
board terminal
terminal
TQ2-L2-3 V
TQ2-L2-4.5 V
TQ2-L2-5 V
TQ2-L2-6 V
TQ2-L2-9 V
TQ2-L2-12 V
TQ2-L2-24 V
TQ2H-L2-3 V
TQ2H-L2-4.5 V
TQ2H-L2-5 V
TQ2H-L2-6 V
TQ2H-L2-9 V
TQ2H-L2-12 V
TQ2H-L2-24 V
Nominal
voltage,
V DC
3
4.5
5
6
9
12
24
Set voltage, Reset voltage,
V DC (max.) V DC (min.)
2.25 2.25
3.38 3.38
3.75 3.75
4.5 4.5
6.75 6.75
99
18 18
Nominal
operating
current,
mA (±10%)
66.7
44.4
40
33.3
22.2
16.7
12.5
Coil
resistance,
(±10%)
45
101.2
125
180
405
720
1,920
Nominal
operating
power,
mW
200
200
200
200
200
200
300
Max.
allowable
voltage,
V DC
4.5
6.7
7.5
9
13.5
18
28.8
Notes: 1. Specified value of the pick-up, drop-out, set and reset voltage is with the condition of square wave coil pulse.
2. Standard packing: Tube: 50 pcs.; Case: 1,000 pcs.
3. In case of 5 V transistor drive circuit, it is recommend to use 4.5 V type relay.
4. AgPd stationary contact types available for high resistance against contact sticking. When ordering, please add suffix "–3" like TQ2-12V-3.
134


Features TESTING LOW PROFILE 2 FORM C RELAY TQ- RELAYS FEATURES 9 .354 26.7 1.051 5+0. 4 –0.2 .197+.016 –.008 9 .354 5+0.4 –0.2 .197+.016 –.008 14 .551 • High sensitivity: 2 Form C: 140 mW powe r consumption (single side stable type) 4 Form C: 280 mW power consumption (si ngle side stable type) • Surge voltag e withstand: 1500 V FCC Part 68 • Sea led construction allows automatic washi ng • Self-clinching terminal also ava ilable • M.B.B. contact types availab le mm inch SPECIFICATIONS Contact Sta ndard (B.B.M) type 2 Form C 4 Form C 50 mΩ Gold-clad silver 1 A 30 V DC 1 A 30 V 0.5 A 125 V AC DC 30 W, 62.5 V A 3 0 W Initial breakdown voltage M.B.B.typ e 2 Form D Initial insulation resistanc e*1 Between open contacts Between conta ct and coil Between contact sets FCC su rge voltage between open contacts Opera te time [Set time]*3 (at 20°C) Release time [Reset time]*4 (at 20°C) M.B.B. time*8 Temperature rise*2 (at 20°C) Fu nctional*5 Shock resistance Destructive*6 Vibration resistance Functional*7 Destructiv.
Keywords TQ2H-L-5V, datasheet, pdf, ETC, LOW, PROFILE, 2, FORM, C, RELAY, Q2H-L-5V, 2H-L-5V, H-L-5V, TQ2H-L-5, TQ2H-L-, TQ2H-L, Equivalent, stock, pinout, distributor, price, schematic, inventory, databook, Electronic, Components, Parameters, parts, cross reference, chip, Semiconductor, circuit, Electric, manual, substitute




@ 2014 :: Datasheetspdf.com :: Semiconductors datasheet search & download site (Privacy Policy & Contact)